Minka Lavery 1137-84 Operating instructions

Brand: Minka Lavery

Model: 1137-84

Type: Operating instructions

Minka Lavery 1137-84 is a lighting fixture that can be used to illuminate various indoor spaces. It features a versatile design that allows for multiple hanging heights, making it suitable for rooms with different ceiling heights. The fixture includes a mounting plate, canopy, nipple, and threaded rods, providing flexibility in customizing the hanging length. The installation process involves connecting the electrical wires, securing the mounting plate to the junction box, and attaching the fixture body to the mounting plate.

INSTALLATION INSTRUCTIONS FOR 1137-84

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

READ AND SAVE THESE INSTRUCTIONS

Fig.1

PREPATION (Fig. 1)

1. Shut off the power at the fuse box or circuit breaker

box. If necessary, remove the old fixture including the

mounting hardware.

2. Carefully remove the new fixture from the carton and

check that all parts are included as shown in the

illustration.

ASSEMBLING THE FIXTURE(Fig.1)

3. Determine the desired hanging height and thread

rods (G, H, I, J) onto the nipple (K). Carefully pass

the wires through each rod as you assemble. Please

remove the nipple if installing with one 6” or 12” rod

only.

4. Loosen the screws (D) (Size: #5-32*0.4”L), and

remove the canopy (C).

5. Slip the canopy (C) over the last rod installed, and

thread the nipple (F) onto the top of the rod.

MOUNTING THE FIXTURE (Fig.1)

6. Raise the mounting plate (A) to the junction box (not

provided), then secure with the junction box screws

(B) (Size: #8-32*0.6”L). The side of the mounting plate

marked “GND” must face out.

7. Install the fixture body into the mounting plate (A) by

tilting at a slight angle so that the hanger ball (E)

slips into the mounting plate (A) as shown. Align the

notch in the hanger ball (E) to the tab on the

mounting plate (A) to prevent the fixture from turning.

CONNECTING THE WIRES (Fig.2)

8. At this point, connect the electrical wires as shown in

figure 2, making sure that all wire connectors are

secured. If your outlet has a ground wire (green or

bare copper), connect the ground wires from the

hanger ball and mounting plate to it. Otherwise,

connect the ground wire from the hanger ball directly

to the mounting plate ground wire and secure with

the wire connectors provided. After wires are

connected, tuck them carefully into the ceiling

junction box.

COMPLETING THE INSTALLATION (Fig. 1)

9. Raise the canopy (C) to the mounting plate (A) and

align the mounting screws (D) to the slots (L). Then

turn canopy (C) clockwise until mounting screws (D)

are in the narrow part of slots (L). Tighten mounting

screws (D) with a screwdriver.

10. Install the light bulbs (included) in accordance with

the fixture’s specifications. (DO NOT EXCEED THE

MAXIMUM WATTAGE!) (NE PAS DEPASSER LA

PUISSANCE NOMINALE MAXIMALE!)

Note: Press spring coupling (M) by hand and

adjust to the desired length of steel wire (N).

Your installation is now complete. Return power to the

junction box and test the fixture.

Fig.2

W30-1-84

W30-H-84

Set# LTG BKT 10

- Mounting strap

- Ground screw

- Mounting screws*2

- Junction box screws*2

Minka Lavery 1137-84 Operating instructions

Brand: Minka Lavery

Model: 1137-84

Type: Operating instructions

Download PDF

report

Minka Lavery 1137-84 Operating instructions

Minka Lavery 1137-84 Operating instructions

Related papers

Other documents