Cobra Electronics iRadar 500 User manual

Type
User manual
Quick Start Guide
Printed in China Part No. 480-667-P Version D
Thank you for purchasing Cobra iRadar
,
the world’s first connected radar/laser/red
light camera detector.
Cobra iRadar uses Bluetooth
®
wireless
technology to connect your iPhone
®
/iPod touch
®
to display radar alerts and change settings.
Follow these simple steps to get your
Cobra iRadar up and running.
Cobra iRadar is made for:
iPhone 4
iPhone 3GS
iPhone 3G
iPod touch (3rd Generation)
iPod touch (2nd Generation)
NOTE: *Location-based alerts and GPS
settings available only with iPhone.
Only radar/laser alerts and settings
will work with iPod touch.
Connecting with Cobra iRadar
Plug in your Cobra iRadar detector unit
using the included cigarette lighter
adapter.
Turn unit on. A red LED will light.
On your iPhone/iPod
touch, enter
the Settings menu.
Press General, then
Bluetooth. Make sure
Bluetooth is switched
to ON.
NOTE: This device complies with part 15 of FCC rules: Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received
including interference that may cause undesired operation.
CAUTION: Modifications or parts not approved by Cobra Electronics
Corporation may violate FCC Rules and void authority to operate this
equipment.
iRADR_QSG_vD.indd 1 9/28/10 12:21 PM
iRadar 100 should
appear under Devices.
Note: Your iPhone/iPod touch
may take 30 seconds to one
minute to recognize the device.
It will initially appear as
Headset” and will then
turn into iRADAR 100.
If you cannot see the device, try restarting
both iRadar and your iPhone/iPod touch and
re-do steps 1 through 5.
Press iRADAR 100,
then press Pair.
The LED on the detector unit will
flash blue. When pairing has
been completed, it will
turn solid blue.
Bluetooth Pairing Tips
If you are having trouble initializing or
maintaining your Bluetooth connection take
the following steps:
1) Turn off your Cobra iRadar detector device,
wait 30 seconds, and then turn it back on.
On your iPhone/iPod Touch, turn Bluetooth
Off and then On again.
2) If you are still not connected, go to the
Bluetooth Settings menu on your iPhone/
iPod Touch. Press the button to the
right of iRADAR 100 and then press
“Forget this Device”. Wait approximately
30 seconds for iRADAR 100 to appear
under Devices and then press iRADAR 100
to reinitialize pairing.
Cobra iRadar App
Dashboard
Display speedometer,
compass and car
battery voltage.
View Map
View user-marked locations,
red light camera locations
in your area and GPS-based
speed & direction of travel.
Settings
Configure your Cobra
iRadar settings.
Note: All radar/laser/red light
camera detector settings will
be inactive if you are not
paired with Cobra iRadar or
are out of range.
To download the App, enter the App Store on
your iPhone/iPod touch and search for Cobra
iRadar” and follow the onscreen instructions.
Now open the App and enjoy using iRadar!
For more information about
AURA
, please visit:
www.cobra.com/AURA.
For more information on iRadar accessories,
go to: www.cobrairadar.com.
3) If iRADAR 100 does not appear under
Devices or you experience an intermittent
Bluetooth connection, completely turn off
both your iPhone/iPod Touch and iRadar
detector unit, wait 30 seconds, and then
turn them back on.
iPod Touch. Press the button to the
iRADR_QSG_vD.indd 2 9/28/10 12:21 PM
  • Page 1 1
  • Page 2 2

Cobra Electronics iRadar 500 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI