Cobra Electronics 480-667-PVERSIOND User manual

Brand: Cobra Electronics

Model: 480-667-PVERSIOND

Type: User manual

Quick Start Guide

Printed in China Part No. 480-667-P Version D

Thank you for purchasing Cobra iRadar

™

the world’s ﬁrst connected radar/laser/red

light camera detector.

Cobra iRadar uses Bluetooth

wireless

technology to connect your iPhone

/iPod touch

to display radar alerts and change settings.

Follow these simple steps to get your

Cobra iRadar up and running.

Cobra iRadar is made for:

iPhone 4

iPhone 3GS

iPhone 3G

iPod touch (3rd Generation)

iPod touch (2nd Generation)

NOTE: *Location-based alerts and GPS

settings available only with iPhone.

Only radar/laser alerts and settings

will work with iPod touch.

Connecting with Cobra iRadar

Plug in your Cobra iRadar detector unit

using the included cigarette lighter

adapter.

Turn unit on. A red LED will light.

On your iPhone/iPod

touch, enter

the Settings menu.

Press General, then

Bluetooth. Make sure

Bluetooth is switched

to ON.

NOTE: This device complies with part 15 of FCC rules: Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received

including interference that may cause undesired operation.

CAUTION: Modiﬁcations or parts not approved by Cobra Electronics

Corporation may violate FCC Rules and void authority to operate this

equipment.

iRADR_QSG_vD.indd 1 9/28/10 12:21 PM

iRadar 100 should

appear under Devices.

Note: Your iPhone/iPod touch

may take 30 seconds to one

minute to recognize the device.

It will initially appear as

“Headset” and will then

turn into iRADAR 100.

If you cannot see the device, try restarting

both iRadar and your iPhone/iPod touch and

re-do steps 1 through 5.

Press iRADAR 100,

then press Pair.

The LED on the detector unit will

ﬂash blue. When pairing has

been completed, it will

turn solid blue.

Bluetooth Pairing Tips

If you are having trouble initializing or

maintaining your Bluetooth connection take

the following steps:

1) Turn off your Cobra iRadar detector device,

wait 30 seconds, and then turn it back on.

On your iPhone/iPod Touch, turn Bluetooth

Off and then On again.

2) If you are still not connected, go to the

Bluetooth Settings menu on your iPhone/

iPod Touch. Press the button to the

right of iRADAR 100 and then press

“Forget this Device”. Wait approximately

30 seconds for iRADAR 100 to appear

under Devices and then press iRADAR 100

to reinitialize pairing.

Cobra iRadar App

Dashboard

Display speedometer,

compass and car

battery voltage.

View Map

View user-marked locations,

red light camera locations

in your area and GPS-based

speed & direction of travel.

Settings

Conﬁgure your Cobra

iRadar settings.

Note: All radar/laser/red light

camera detector settings will

be inactive if you are not

paired with Cobra iRadar or

are out of range.

To download the App, enter the App Store on

your iPhone/iPod touch and search for “Cobra

iRadar” and follow the onscreen instructions.

Now open the App and enjoy using iRadar!

For more information about

AURA

™

, please visit:

www.cobra.com/AURA.

For more information on iRadar accessories,

go to: www.cobrairadar.com.

3) If iRADAR 100 does not appear under

Devices or you experience an intermittent

Bluetooth connection, completely turn off

both your iPhone/iPod Touch and iRadar

detector unit, wait 30 seconds, and then

turn them back on.

iPod Touch. Press the button to the

iRADR_QSG_vD.indd 2 9/28/10 12:21 PM

Cobra Electronics 480-667-PVERSIOND User manual

Cobra Electronics 480-667-PVERSIOND User manual

Cobra Electronics 480-667-PVERSIOND User manual

Related papers

Other documents