2. MIMAKI
  3. Tx3-1600

MIMAKI Tx3-1600 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the MIMAKI Tx3-1600 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I set the machine condition after plotting?
    How to select printing type?
    How to set heater temperature after plotting?
    How to set media retreat operation after plotting?
    What is the initial value of heater temperature and media retreat operation?
    What does the LCD display when the heater is set to OFF?
    What does the LCD display when either Leaf is selected or “TakeUp Dev” is set to OFF?
    How to return to the LOCAL mode?
    What does the LCD display when heater is ON and heater temperature after plotting is lower than setting value?
    What does the LCD display before plotting and before executing jog, in the case [Belt Wash] is set to [ON]?
Supplement for the Basic Operation manual
MIMAKI ENGINEERING CO., LTD.
D201507
This is the additional explanation of the
update functions on the Tx3-1600 opera-
tion manual.
Please read and fully understand this
manual before using the device.
Table Contents
For the users refer to English operation manual ................................ 4
Setting Printing Conditions............................................................................................... 4
- 4 -
For the users refer to English operation manual
Following functions are added after the Operation Manual P4-20.
Setting Printing Conditions
Set the machine condition of after plotting [EndOfPrint]
Set the heater temperature, and media retreat operation for after plotting.
STEP
1. Select a type. (Refer to Page 4.4)
Here, select [Type.1].
2. Press [ENTER] key.
3. Select [EndOf Print] by pressing the JOG
keys [ ] or [ ].
4. Press [ENTER] key.
5. Select the setting of heater after plotting by
pressing the JOG keys [ ] or [ ].
[OFF], [LOW], [MID], [HIGH]
• The initial value is a setting value of [Heater Temp].
(P.4-20)
• In the case heater is set to OFF (P.4-20), heater
temperature setting is disabled and following message
is displayed on the LCD.
6. Press [ENTER] key.
7. Select the media retreat operation of after
plotting by pressing the JOG keys [ ] or [ ].
[OFF], [ON]
• Initial value is[OFF].
• In the case of either Leaf is selected (P.2-23) or “Take-
Up Dev” is set to OFF (P.4-17), media retreat setting is
disabled and following message is displayed on the
LCD.
TYPE1
Heater Temp
: OFF
SETUP
Select.
: TYPE1
TYPE1
Media Comp. < ent >
TYPE1
MediaRetreat
: OFF
TYPE1
EndOf Print < ent >
TYPE1
Heater Temp
: MID
TYPE1
MediaRetreat
: ON
TYPE1
Heater Temp : N / A
TYPE1
MediaRetreat : N / A
- 5 -
<< LOCAL >>
width : 1620mm
TYPE1
EndOf Print < ent >
8. Press [ENTER] key.
9. Press [END] key twice, and the menu re-
turns to the LOCAL mode.
Following indications are added.
Indication of Heater temperture for REMOTE mode
Indicated in the case heater is set to ON and heater temperature after plotting is lower than setting value.
Indication of media retreat operation after plotting
Indicated when plotting complete, in the case [Media Retreat] is set to [ON] for the setting of after plotting.
Indication for Belt Wash Brush UP
Indicated before plotting and before executing jog, in the case [Belt Wash] is set to [ON](P4-19).
BeltWash BrushUP
Please Wait
Media Retreat
Please Wait
<REMOTE>
TYPE1 ∗∗ . ∗ m
<REMOTE> Heater
OFF->HIGH?[ > ] Key
Indicated alternately
Heater temperature while plotting.
Heater temperature while aidling
By pressing the key, re-
setting the value to the setting
value of heater temperature while
plotting.
/