Kohler K-2610-MU-NA Installation guide

Installation Guide

Self-Rimming/Undercounter Lavatories

M product numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

M corresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-2600 K-2602, K-2603

K-2605 K-2610

K-2611 K-2612

1018896-2-C

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

Observe all local plumbing and building codes.

Prior to installation, unpack the new lavatory and inspect it for

damage. Return the lavatory to its protective carton until you are

ready to install it.

Inspect the drain and supply tubing. Replace if necessary.

Do not substitute another sealant if one is supplied with this

lavatory.

Use the template supplied with the lavatory.

For replacement installations, make sure the existing cutout is the

same size or smaller than needed for the new lavatory.

Pencil

Drill

Screwdriver

Keyhole Saw

Template

(supplied)

Safety

Glasses

Adjustable

Wrench

Tape

Measure

Plus:

• 1/2" drill bit

• Ruler

• Hole Saw

• Gloves

1018896-2-C 2 Kohler Co.

1. Preparation

Install the water supplies and drain piping according to the

roughing-in information.

Determine the faucet centerline location. Consider the faucet and

handle escutcheon diameters, the length of the spout, and the

clearance between the spout and the lavatory rim.

Calculate the faucet centerline measurement by ﬁrst dividing the

escutcheon diameter by 2, and then adding 1/4″ (6 mm) to the

result. If necessary, round the calculation up to the nearest 1/16″

(2 mm).

Carefully draw the calculated faucet centerline on the cut-out

template. Choose the most suitable location based upon the

following factors:

•

compliance with all local plumbing codes

•

minimum 2″ (5.1 cm) distance from the water stream to the

lavatory rim edge. This is important to ensure adequate clearance

for hand washing

•

a minimum 1/4″ (6 mm) distance between the faucet spout and

the lavatory rim

Redraw the faucet centerline as needed to meet these

requirements.

Draw a line on the cut-out template a minimum of 2″ (5.1 cm)

behind the ﬁnal faucet centerline. This is the minimum

backsplash locator line.

Handle

Escutcheon

Calculated Faucet

Centerline Distance

2" (5.1 cm)

Min.

Backsplash

Countertop

Template

Rim Outline

Centerline

2" (5.1 cm) Min.

1/4" (6 mm) Min.

Kohler Co. 3 1018896-2-C

Preparation (cont.)

NOTE: Some Kohler faucets require a minimum of 2-1/2″ (6.4 cm)

behind the ﬁnal faucet centerline.

Cut along the backsplash locator line on the template.

Cut out the template along the inside of the template cutting line.

Position the template on the countertop to ensure clearance

between the lavatory, faucet, and backsplash.

Verify cabinet clearance beneath the countertop.

Use a pencil to trace the template on the countertop.

Mark the faucet and handle centerline on the countertop.

1018896-2-C 4 Kohler Co.

2. Self-Rimming Installation

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

Cut out the opening by carefully following the pencil line traced

from the template.

Temporarily position the lavatory in the countertop to check ﬁt.

Remove the lavatory.

Drill the faucet holes according to the faucet installation

instructions.

Install the faucet to the countertop according to the

manufacturer’s instructions.

Install the drain to the lavatory according to the drain

manufacturer’s instructions.

NOTE: When installing the K-7702 drain, use the tapered gasket

supplied with the lavatory instead of the gasket supplied with the

drain.

CAUTION: Risk of product damage. Overtightening the wing

nuts may cause irreparable damage to the lavatory.

Apply bead of sealant around entire underside of lavatory rim

between stud and rim edge.

Place the lavatory into the cut-out hole and position.

Self-Rimming Installation

Lavatory

Sealant

Stud

Kohler Co. 5 1018896-2-C

Self-Rimming Installation (cont.)

Assemble the clip and wing nut to the stud and carefully

ﬁnger-tighten to remove any gaps between the lavatory rim and

the countertop. Do not overtighten the wing nuts.

Remove any excess sealant using damp cloth.

Allow sealant to set for 30 minutes before proceeding.

Proceed to the Complete the Installation section.

1018896-2-C 6 Kohler Co.

3. Undercounter Installation

Cut-Out Dimensions

AB C

K-2610 Round Lav. 10-1/8″ (25.7

cm)

10-1/8″ (25.7 cm) N/A

K-2612 Round Lav. 13-1/2″ (34.3

cm)

13-1/2″ (34.3 cm) N/A

K-2611 Oval Lav. 9-3/4″ (24.8 cm) 11-3/4″ (29.8 cm) N/A

K-2602 Elliptical 13-3/4″ (34.3

cm)

12″ (30.5 cm) 23-5/8″

(60 cm)

Cut out the opening by carefully following the pencil line traced

from the template.

Install Wood Countertop

Mark and pre-drill the wood screw holes at the locations shown

on the previous table.

Waterproof any exposed areas of wood.

Install Marble/Stone Countertop

Position the countertop upside down on foam padding to protect

the surface.

Wood Countertop

Lavatory

Sealant

Undercounter Installation

Marble Slab / Solid Surface

Countertop

Lavatory

Insert

Sealant

Reference Hole

Location

A

C

B

Kohler Co. 7 1018896-2-C

Undercounter Installation (cont.)

Mark and drill 3/8″ holes 5/8″ (1.6 cm) deep at the locations

shown on the previous table.

Use a setting tool and hammer to secure the anchors.

For All Undercounter Installations

WARNING: Risk of personal injury. Metal surfaces are sharp

and can cause severe cuts. Use gloves and handle lavatory

edges carefully.

If the countertop has not been installed, install it at this time.

Drill the faucet holes according to the faucet installation

instructions.

Install the faucet to the countertop according to the faucet

manufacturer’s instructions.

Install the drain to the lavatory according to the drain

manufacturer’s instructions.

NOTE: When installing the K-7702 drain, use the tapered gasket

supplied with the lavatory instead of the gasket supplied with the

drain.

Apply a continuous bead of quality sealant to the top surface of

the lavatory rim where it will contact the countertop.

NOTE: The screws provided should be used on countertops with a

minimum 1″ (2.5 cm) thickness. For thinner countertops, use

appropriate anchors and fasteners (not provided).

For wood, wood composite, and marble countertops, install the

lavatory to the countertop with the clamps and screws provided.

For other countertop materials, refer to the countertop

manufacturer’s instructions for recommended fasteners.

CAUTION: Risk of product damage. Overtightening the nuts

may cause irreparable damage to the lavatory.

Position the lavatory squarely under the cutout before tightening

the clamps. Draw the lavatory rim up against the countertop until

it is snug. Do not overtighten.

Immediately wipe away any excess sealant, and ﬁll any voids as

needed.

Allow the sealant to set for 30 minutes before proceeding.

Proceed to the Complete the Installation section.

1018896-2-C 8 Kohler Co.

4. Complete the Installation

Assemble the adjustable drain pop-up linkage.

Apply plumbers putty to the underside of the drain ﬂange.

Insert the drain ﬂange into the drain hole of the lavatory.

From underneath the lavatory, apply plumbers putty to the

underside of the drain area.

Slide the gasket, tapered side down, followed by the chrome

plated brass tube on to the drain ﬂange.

Slide the other gasket, tapered side up, onto the drain ﬂange and

push the gaskets and tube up against the underside of the

lavatory.

Slide the ﬂat washer onto the drain ﬂange and up against the

bottom gasket.

Secure the assembly with the locknut.

Connect and tighten the trap to the drain, and complete the water

supply connections to the faucet according to the instructions

packed with the faucet.

Run water into the lavatory and check for leaks.

Clean up with a non-abrasive cleaner.

Turn the water supplies on and check for leaks.

Drain Flange

(Purchased)

Apply

plumbers

putty.

Tapered Gasket

Flat Washer

Locknut

Chrome Plated

Brass Tube

Kohler Co. 9 1018896-2-C

Page is loading ...

Kohler K-2610-MU-NA Installation guide

This manual is also suitable for

Kohler K-2610-MU-NA Installation guide

in other languages

Related papers

Other documents