Trendnet RB-TV-IP410WN Owner's manual

Category
WLAN access points
Type
Owner's manual

This manual is also suitable for

-1-
PREFACE
Thank you for purchasing the SecurView Wireless N Pan/Tilt Internet
Camera, a powerful wireless network camera that provides the high
qualityimageviatheInternetconnection. The camera’span/tilt functions
allowyoutocontrolthecameratomonitoreverywhereremotely.Through
the GPIO connectors, the camera can attach a variety of
external devices
for your specific purposes. The camera can be installed as a standalone
system within your application environment easily and quickly, and
supportsremotemanagementfunctionsothatyoucanaccessandcontrol
itusingaWebbrowseronyourPC.
This Advanced Installation Guide provides you with the
instructions and
illustrationsonhowtouseyourcamera,whichincludes:
Chapter1 Introduction to Your Camera describes the features of the
camera.Youwillalsoknowthecomponentsandfunctionsof
thecamera.
Chapter2 HardwareInstallationhelpsyouinstallthecameraaccording
toyourapplication environment. Youcan use
this camera at
home,atwork,atanywhereyouwant.
Chapter3 Accessing the Camera lets you start using your camera
without problem. The camera can be set up easily and work
withinyournetworkenvironmentinstantly.
Chapter4 ConfiguringtheCameraguidesyouthroughtheconfiguration
ofthe
camerausingtheWebbrowseronyourPC.
Chapter5 Appendixprovidesthespecificationofthecameraandsome
usefulinformationforusingyourcamera.
NOTE The illustrations and configuration values in this guide are for
reference only. The actual settings depend on your practical
applicationofthecamera.
-2-
Contents
PREFACE.........................................................................1
CHAPTER 1......................................................................4
INTRODUCTION T O YOUR C AMERA...........................................4
1.1 CHECKINGTHEPACKAGECONTENTS..............................................4
1.2 GETTINGTOKNOWYOURCAMERA...............................................5
1.3 FEATURESANDBENEFITS............................................................7
1.4 SYSTEMREQUIREMENT...............................................................9
CHAPTER 2....................................................................10
HARDWARE INSTALLATION..................................................10
2.1 INSTALLINGTHEWALLMOUNTKIT.............................................10
2.2 CONNECTINGTHECAMERATOLAN/WLAN................................11
2.3 APPLICATIONSOFTHECAMERA..................................................12
CHAPTER 3....................................................................13
ACCESSING THE C AMERA....................................................13
3.1 USINGIPSETUP.......................................................................13
3.2 ACCESSINGTOTHECAMERA......................................................14
3.3 CONFIGURINGTHEIPADDRESSOFTHEPC...................................18
CHAPTER 4....................................................................19
CONFIGURING T HE C AMERA ................................................19
4.1 USINGTHEWEBCONFIGURATION..............................................19
4.2 USINGSMARTWIZARD.............................................................20
4.3 BASICSETUP...........................................................................23
4.4 NETWORKSETTINGS................................................................28
4.5 PAN/TILTSETTINGS.................................................................37
4.6 SETTINGUPVIDEO...................................................................38
4.7 EVENTSERVERCONFIGURATION.................................................41
4.8 MOTIONDETECT.....................................................................44
4.9 EVENTCONFIG........................................................................45
4.10 TOOLS...................................................................................50
4.11 DEVICEINFO...........................................................................52
CHAPTER 5....................................................................53
-3-
SECURV IEW P RO S OFTWARE..............................................53
5.1 INSTALLATION.........................................................................54
5.2 USINGSECURVIEWPRO.........................................................57
5.2.4EMAPSETUP&CAMERASTATUS...............................................74
CHAPTER 6....................................................................88
How to access the camera behind a Router.....................88
APPENDIX.....................................................................94
A.1 SPECIFICATION........................................................................94
A.2 GPIOTERMINALAPPLICATION...................................................97
A.3 GLOSSARYOFTERMS................................................................98
-4-
CHAPTER1
INTRODUCTIONTOYOURCAMERA
1.1 CheckingthePackageContents
Check the items contained in the package carefully. You should have the
following:
5 OneTVIP410WN
5 OnePowerAdapter
5 OneExternalAntenna
5 OneCameraStand/MountingKit
5 OneGPIOConnector
5 OneNetworkCable
5 OneCDROM(Utility&User’sGuide)
5 OneMultiLanguageQuickInstallationGuide
NOTE Once any item contained is damaged or missing, contact the
authorizeddealerofyourlocale.
-5-
1.2 GettingtoKnowYourCamera
FrontView
Lens
Power LED
indicates the camera
is powered on with
the steady amber
light.
Link LED
indicates the camera’s
network connectivity
with the flashing green
light.
-6-
RearView
*FormoreinformationoftheWPSbutton,refertotheinstructionoftheWebConfiguration,
Network>>Wireless>>WPSSetting.
GPIO Connectors
is used to connect the
external devices.
Reset Button
will restart the camera when it is
pressed quickly; when it is
pressed and held for five
seconds, the camera will resume
the factory default settings.
DC Power Connector
connects the AC power
adapter, in order to
supply power to the
camera.
Ethernet Cable Connector
connects the network cable.
External Antenna
Connector connects the
external antenna.
WPS Button*
is used to protect your
wireless network and for
easy wireless connection
setup.
-7-
1.3 FeaturesandBenefits
MJPEGcodecSupported
The camera provides you with excellent images by the MJPEG codec
technology,allowingyoutoadjustimagesizeandquality,andbitrate
accordingtothenetworkingenvironment.
OptimalViewing
Withthepan/tilefunctions,youcaneasilymonitoreverywhereviathe
camera by moving the camera
lens to the left/right (310 degrees) or
up/down (105 degrees). In addition, you can assign up to eight
positionsforthecamera,enablingyoutomovethecameralenstothe
desiredpositionquickly.
I/OConnectorsProvided
The camera provides the I/O connectors on the rear panel (IN/OUT),
which
providethephysicalinterfacetosendandreceivedigitalsignals
to a variety of external alarm devices. You can connect a special
featured device, and then configure the settings and control the
devicefromtheGPIOTriggerwindowofWebConfiguration.
RemoteControlSupported
By using a standard Web browser
or the bundled SucurView™ Pro
software application, the administrator can easily change the
configuration of the camera via Intranet or Internet. In addition, the
cameracanbeupgradedremotelywhen a new firmware isavailable.
The users are also allowed to monitor the image and take snapshots
viathenetwork.
-8-
MultiplePlatformsSupported
The camera supports multiple network protocols, including TCP/IP,
SMTP email, HTTP, and other Internet related protocols. Therefore,
you can use the camera in a mixed operating system environment,
suchasWindowsVistaandWindows7.
MultipleApplicationsSupported
Through the remote access technology, you
can use the cameras to
monitorvariousobjectsandplacesforyourownpurposes.
For example, babies at home, patients in the hospital, offices and
banks,andmore.Thecameracancapturebothstillimagesandvideo
clips,sothatyoucankeepthearchivesandrestorethematany
time.
WPSSupported
WPS(WiFiProtectedSetup)standardisanewsolutionthatsimplifies
theprocessofconfiguringWiFisecuritysettings,allowingyouto
establishasecurewirelessnetworkbysimplypressingabutton.
-9-
1.4 SystemRequirement
Networking
LAN: 10BaseTEthernetor100BaseTXFastEthernet.
WLAN: IEEE802.11b/g,BasedonIEEE802.11nTechnology.
AccessingtheCamerausingWebBrowser
Platform: Microsoft®Windows®XP/Vista/Win7
CPU: IntelPentiumIII800MHzorabove
RAM: 512MB
Resolution: 800x600orabove
UserInterface: Microsoft®InternetExplorer6.0or
above
AppleSafari2orabove
MozillaFirefox2.00orabove
GoogleChrome
AccessingtheCamerausingSucurViewPro
Platform: Microsoft®Windows®XP/Vista/Win7
Resolution: 1024x768orabove
HardwareRequirement:
1~8cameras:IntelCore2Duo2GBRAM
9~32cameras:IntelCore2Quad4GBRAM
NOTE If you
connect multiple cameras to monitor various places
simultaneously, you are recommended to use a computer with
higherperformance.
-10-
CHAPTER2
HARDWAREINSTALLATION
2.1 InstallingtheWallMountKit
ThecameracomeswithaWall Mount Kit,whichallowsyoutoplaceyour
cameraanywherebymountingthecamerathroughthethreescrewholes
locatedinthebaseoftheWallMountKit.

Screw
Screw
Screw
-11-
2.2 ConnectingtheCameratoLAN/WLAN
Use the provided Ethernet cable to
connectthecameratoyourlocalarea
network(LAN).
When you connect the AC power
adapter, the camera is powered on
automatically. You can verify the
power status from the Power LED on
thefrontpanelofthecamera.
Once connected, the Link LED starts
flashinggreenlightand the camera is
onstandbyandreadyforusenow.
If you use a wireless network in your
application environment, you need to
attach the included external antenna
tothecamera.
Whenthe camera is powered on, the
camera will automatically search any
accesspointwith“default”SSID.
NOTE Ifthecameracannottoyourwireless network, you needto install
thecamerainLANandproceedwithWLANsettings.
Connecting the Ethernet Cable
Connecting the External Antenna
-12-
2.3 ApplicationsoftheCamera
Thecameracanbeappliedinmultipleapplications,including:
MonitorlocalandremoteplacesandobjectsviaInternetorIntranet.
Capturestillimagesandvideoclipsremotely.
Uploadimagesorsendemailmessageswiththestillimagesattached.
The following diagram explains one of the typical applications for
your
cameraandprovidesabasicexampleforinstallingthecamera.
HomeApplications
-13-
CHAPTER3
ACCESSINGTHECAMERA
3.1 UsingIPSetup
Thecameracomeswithaconvenientlyutility,IPSetup,whichisincludedin
the Installation CDROM, allowing you to search the camera on your
networkeasily.
1. InserttheInstallationCDROMintoyourcomputer’sCDROMdriveto
initiatetheAutoRunprogram.
2. Click the IPSetup item to launch
the utility. The control panel will
appearasbelow.
3. Onceyou get the IP addressof thecamera, launch the Web browser
orSucurViewProtoaccessyourcamera.
Displaytheconnected
camera(s).
Doubleclicktolinkthe
Camera.
ClickAbouttogettheVersioninformationofIPSetup
ClickLinktoconnecttheselectedcamera.
ClickChangeIPtomodifytheIPaddressoftheselectedcamera.
ClickSearchtofindtheIPaddressoftheconnectedcamera(s).
ClickExittoclosetheutility.
-14-
3.2 AccessingtotheCamera
Wheneveryouwanttoaccessthecamera:
1. SincethedefaultconfigurationofthecameraisDHCPmodeenabled,
youarerecommendedtolaunchIPSetuptosearchtheIPaddressthat
is assigned to the camera by the DHCP server, and then click Link to
accessthecameraviatheWeb
browser.
2. IfNetworkCameracan'tgetIPAddressunderDHCPmode,thedefault
IPAddresswillbe192.168.10.30.
3. Whentheloginwindowappears,enterthedefaultUsername(admin)
and password (admin) and press OK to access to the main screen of
thecamera’sWebConfiguration.
NOTE Ifyouareinitiallyaccessto thecamera,youwillbeask to install a
new plugin for the camera. Permission request depends on the
Internetsecuritysettingsofyourcomputer.ClickYestoproceed.
EntertheUsername
andPassword.
-15-
Afteryou login into the Web Configuration of the camera, the main page
willappearasbelow:
The main page of the Web Configuration provides you with many useful
informationandfunctions,including:
Camera Information
Displaysthecamera’slocationandthecurrent
date & time. The information can be modified in the Web
Configuration.
Live View Image
Displays the realtime image of the connected
camera.
Pan/Tilt Buttons
Live View/Setup Switch
Camera Information
Live View Ima
g
e
Zoom In Buttons Ni
g
htmode Button
Function Buttons
-16-
z Move your mouse to the Live View area and click on anywhere,
thecameralenswillthenmovetothepositionwhereyouclicked
todisplayitinthecentralpartofLiveViewarea.
z When you enlarge the Live View by clicking the Zoom In buttons
(2x
or 3x), you can move the displayed image by rightclicking
yourmouseontheLiveView area.Thepositionwhereyouright
clickedwillbedisplayedinthecentralpartofLiveViewarea.
ZoomInButtons
Clickthebuttonstozoomintheliveviewimageby
1x,2x,and3x.
NightmodeButton
Clickthebuttontoenablethe“nightshotmode”
to deliver clearer images in the dark environment. However, this will
reducetheframerateofvideosetting.
Live View/Setup Switch
Click Setup to configure the camera. For
details,seeChapter4andClicktheLive Viewbuttontoreturn tothe
Mainscreentoviewtheliveviewimage.
Pan/TiltButtons
Providesthebuttonstocontrolthecameralens:
z Left/Right/Up/Down/Home buttons allow you to move the
camera lens position. Clicking the Home button will move the
cameralenstotheassignedhomeposition.
z AutoPatrolbuttoncontrolsthecameratoautomaticallyscanthe
presetpositionsonce.ClickStopto
stoppatrolling.
z Click the Number button (1~8) to move the camera lens to the
presetpositionimmediately.
To set up the preset positions, move the camera lens by clicking
theLeft/Right/Up/Downbuttonstothedesiredpositionfirst,then
select the number (1~8) from the pulldown list and click the
Applybutton.You can entera descriptive name for the assigned
positioninthetextboxtoidentifyiteasily.
FunctionButtons
Usethesebuttonstocontrolthevideo,andtrigger
functions.
-17-
z ManualRecordallowsyoutorecordandsaveavideoclip.
z Snapshotallowsyoutocaptureandsaveastillimage.
z Browse allows you to assign the destination folder to store the
videoclipsandstillimages.
z TriggerOutallowsyou totriggeron/offtheGPIO
outputmanually.
NOTE IfyourPCuseMicrosoftVistaplatform.Maybeyoucan’tfindthese
recorded files what stored by Snapshot or Manual Record. That
you need to disable the protected mode of Security in the IE
Browser.PleasefollowasbelowSteps:
1. OpenIEBrowser
2. Select
ToolsÆInternetOptions
3. SelectSecurity
4. DisabletheEnableProtectedModethenpressOK
-18-
3.3 ConfiguringtheIPAddressofthePC
If you are failed to access to the camera, please check the IP address of
your computer. When you connect the camera to your computer directly
to proceed with configuration of the camera, you need to set up the IP
addressestobeinthesamesegmentforthetwodevices
tocommunicate.
1. On your computer, click Start > Control Panel to open the Control
Panelwindow.
2. Doubleclick Network Connection to open the Network Connection
window.
3. RightclickLocal Area Connection and then click Properties from the
shortcutmenu.
4. When the Local Area Connection Properties window
appears, select
theGeneraltab.
5. SelectInternetProtocol[TCP/IP]andthenclickPropertiestobringup
theInternetProtocol[TCP/IP]Propertieswindow.
6. To configure a fixed IP address that is within the segment of the
camera,selecttheUsethefollowingIPaddressoption.Then,enteran
IP address
into the empty field. The suggested IP address is
192.168.10.x(xis1~254except30),andthesuggestedSubnetmaskis
255.255.255.0.
7. Whenyouarefinished,clickOK.
-19-
CHAPTER4
CONFIGURINGTHECAMERA
4.1 UsingtheWebConfiguration
YoucanaccessandmanagethecamerathroughtheWebbrowserandthe
provided software application SucurView Pro. This chapter describes the
Web Configuration, and guides you through the configuration of the
camerabyusingtheWebbrowser.
To configure the camera, click Setup on the main page of Web
Configuration.
TheWebConfigurationwillstartfromtheBasicpage.
TheWebConfigurationcontainsthe
settingsthatarerequiredforthe
cameraintheleftmenubar,including
SmartWizard,Basic,Network,Video,
EventServer,Motiondetect,Event
Config,Tools,andInformation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Trendnet RB-TV-IP410WN Owner's manual

Category
WLAN access points
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI