Reznor XBWS Installation guide

Brand: Reznor

Model: XBWS

Category: Air filters

Type: Installation guide

INSTALLATION INSTRUCTIONS

EN ERGY RE COV ERY VEN TI LA TOR

Applies To Model XBWS When Used With Option AQ20

Side By Side Design

INSTALLATION INSTRUCTIONS FOR ROOFTOP STAND ALONE

ENERGY RECOVERY UNIT IN SIDE BY SIDE DESIGN

FORM RZ-NA-I-XBWS-AQ20

MAY 29, 2014

SUPERCEDES 09-27-13

SXX-2ZERV

PAGE 1

I - Ship ping and Pack ing List

Package contains:

1 — Energy Recovery Ventilator Assembly

I I - Ship ping Dam age

Check unit for shipping damage. Receiving party should

contact last carrier immediately if shipping damage is

found.

III - Gen eral

These instructions are intended as a general guide and do

not supersede local codes in any way. Authorities having

jurisdiction should be consulted before installation.

IV - Re quire ments

When installed, the unit must be electrically wired and

grounded in accordance with local codes or, in absence of

local codes, with the current National Electric Code,

ANSI/NFPA No. 70.

V - Ap pli ca tion

These Energy Recovery Ventilators (ERV) are used in a

down discharge manner equipped with field provided

balancing damper assembly through the roof. A roof

curb must be provided to Rooftop Systems specifications.

These wheels conserve energy by mixing warmer air with

cooler air in the following manner:

Re cov ery Wheel Mode

The Recovery Wheel mode is accomplished by two

blowers providing continuous exhaust of stale indoor air

and replacement by equal amount of outdoor air. Energy

recovery is achieved by slowly rotating the energy

recovery wheel within the cassette frame work. In winter,

the ERV adsorbs heat and moisture from the exhaust air

stream during one half of a complete rotation and gives

them back to the cold, drier intake air supply during the

other half rotation. In summer, the process is automatically

reversed. Heat and moisture are absorbed from incoming

fresh air supply and transferred to the exhaust air stream.

This process allows outdoor air ventilation rates to be

increased by factors of three or more without additional

energy penalty or increase in size of heating or air

conditioning systems.

VI - Rig ging Unit For Lift ing

1. Maximum weight of unit is — Varies per Series

{300-1200 Lbs.} (Crated)

2. Remove crating.

3. All panels must be in place for rigging.

4. Remove hood assemblies from door marked filter

access.

5. Place 2" filter in filter rack and replace filter access

door.

6. Roof curb gasket must be applied to all top surfaces of

the curb. (Refer to roof curb installation instruction.)

7. Forklift channels must be removed from the base of

ERV before setting unit on curb. See Figure 1.

8. Position unit on roof curb and provide service access

to ERV control access door and wheel.

CAUTION

Danger of sharp metallic edges. Can cause injury.

Take care when servicing unit to avoid accidental

contact with sharp edges.

WARNING

Electric shock hazard. Can cause injury

or death. Before attempting to perform

any service or maintenance, turn the

electrical power to unit OFF at

disconnect switch(es). Unit may have

multiple power supplies.

FIGURE 1

FORKLIFT CHANNELS

Energy recovery COMPONENT certified

to the AHRI Air-to-Air Energy Recovery

Ventilation Equipment Certification

Program in accordance with AHRI

Standard 1060-2000. Actual performance

in packaged equipment may vary.

ETL Certified per UL 1995

and CSA 22.2

VII - In stal la tion

Fresh Air Hood As sem bly (See Fig ure 2)

1. Secure hood sides (A and C) to Hood top (B) using the

supplied #10 x ½ screws.

2. Secure filter channels (F and D) to hood sides using

the supplied #10 x ½ screws.

3. Secure hood bottom (E) to the inside of the hood sides

using the supplied #10 x ½ screws.

4. Slide the fresh air filter (H) into the tracks created by

the front of the hood sides and the filter channels.

5. Secure the filter panel (G) to the hood sides. Slide the

filter panel under the front flange of the hood top.

6. Install fresh air hood on ERV.

7. Install barometric exhaust hood over exhaust blower

outlet.

8. Connect field duct connections to duct flanges on back

of ERV. Seal duct connections.

9. Remove ERV control access panel to connect field

wiring.

10. Route class II low voltage wire (3 conductor) from

thermostat or energy management through small

bushing in end panel of ERV. See wiring diagram.

a. Thermostat (dependent) - connect in parallel at

rooftop unit with “G”, “C” and “W”. Then connect

matching color at terminal 1, 2, and 3 respectively

on ERV circuit board.

b. Energy Management - provide +24 VAC to “1” and

common, 24 VAC to “2’ terminals on ERV circuit

board.

c. Thermostat (dedicated) - splice into +24 vac (blue

wire) at (control circuit board) transformer

connection run wire to "R" terminal. Then run

another wire from "G" terminal to ERV (control

circuit board) terminal block #1.

11. All electrical connections must conform to any local

codes and current National Electric Codes (NEC) and

Canadian Electric Codes (CEC). Refer closely to unit

wiring diagram in unit and/or in these instructions for

proper wiring connections.

12. Refer to the unit nameplate for minimum circuit

ampacity (MCA) and maximum overcurrent protection

size (fuse).

13. Electrical data is listed on unit rating plate and motor

name plates.

14. Connect line voltage power supply to ERV fuse block

in control box of unit from disconnect switch. See

wiring diagram.

15. Ground unit with a suitable ground connection either

through unit supply wiring or an earth ground.

Note: Unit voltage entries must be sealed weather

tight after wiring is complete.

16. Remove motor access panels. Locate belts fastened

to blower assembly. Install belt onto motor and blower

pulley. Adjust motor sheave to correct blower RPM for

CFM and external static pressure requirements. See

charts in this instruction. Multiple pulley arrangements

are available to meet the entire range.

PAGE 2

Caution: Blower speed must be adjusted for the given

external static pressure and airflow (CFM)

requirements. If blower speed is not adjusted

for conditions, possible motor over loading can

occur.

17. Replace access panel onto the ERV unit and secure.

18. Restore power to unit.

19. Cleanup once unit is operating properly, caulk any

open joints, holes or seams to make the units

completely air and water tight.

20-Leave this instruction manual with owner or in an

envelope to be kept near unit.

VIII - Op er a tion

How It Works

The unit contains an Energy Recovery Wheel (ERW) that

is a new concept in rotary air-to-air heat exchangers.

Designed as a packaged unit for ease of installation and

maintenance, only the connection of electrical power is

required to make the system operational.

When slowly rotating through counter flowing exhaust and

fresh air streams the ERW adsorbs sensible heat and

latent heat from the warmer air stream and transfer this

total energy to the cooler air stream during the second half

of its rotating cycle. Rotating at 50-60 revolutions per

minute, the wheel provides constant flow of energy from

warmer to cooler air stream. The large energy transfer

surface and laminar flow through the wheel causes this

constant flow of recovered energy to represent up to 85%

of the difference in total energy contained within the two air

streams.

Sensible and latent heat are the two components of total

heat. Sensible heat is energy contained in dry air and latent

heat is the energy contained within the moisture of the air.

The latent heat load from the outdoor fresh air on an air

conditioning system can often be two to three times that of

the sensible heat load and in the winter it is a significant

part of a humidification heat load.

During both the summer and winter, the ERW transfers

moisture entirely in the vapor phase. This eliminates wet

surfaces that retain dust and promote fungal growth as well

as the need for a condensate pan and drain to carry water.

(E)

(B)

(C)

(A)

(F)

(D)

(G)

(H)

FIGURE 2

ASSEMBLED FRESH AIR HOOD

PAGE 3

Because it is constantly rotating when in the air stream, the

ERV is always being cleaned by air, first in one direction

then the other. Because it is always dry, dust or other

particles impinging on the surface during one half cycle,

are readily removed during the next half cycle.

During the heating season, when outdoor air temperatures

are below 15

F, it is recommended to use the (optional)

low ambient kit (field installed).

Low Ambient Kit is appropriate for climates with limited

HVAC system operation when outdoor temperatures are

below 10

The frost threshold is the outdoor temperature at which

frost will begin to form on the ERV wheel. For Energy

Recovery Ventilators, the frost threshold is typically below

F. Frost threshold is dependent on indoor temperature

and humidify. The table shows how the frost threshold

temperatures vary depending on indoor conditions

FROST THRESH OLD TEM PER A TURE

IN DOOR RH AT 70

FROST THRESH OLD

TEM PER A TURE

20% 0

30% 5

40% 10

Because Energy Recovery Ventilators have a low frost

threshold, frost control options are not necessary in many

climates. Where outdoor temperatures may drop below

the frost threshold during the ERV operational hours,

exhaust only frost control option is available.

Low Am bi ent Kit (Op tional)

Low Ambient Kit turns off the supply blower when outdoor

temperatures fall below the frost threshold. The exhaust

only thermostat set points are field adjustable. Supply fan

operation is automatically restored when the exhaust air

temperature rises above the thermostat set point.

Provisions for introducing make-up air into the building

when the supply blower is off to avoid depressurization

should be considered.

Re cov ery Wheel Mode

On a thermostat call for blower operation in heating,

cooling or continuous blower, the ERW will rotate between

fresh air and exhaust air streams. Both the fresh air and

exhaust air blowers will also be operating to overcome the

air resistance of the ERV.

IX - Sys tem Check

1. Disconnect main power.

2. Turn to “Cont” for blower operation on thermostat

controlled models.

3. Restore power to unit. Observe ERV wheel rotation

and both fresh air and exhaust air blowers will

operating.

Note: If Low ambient kit is used the jumper between

TB37-5 & TB37-6 should be removed. Also if

system check out is being conducted at low

ambient temperatures, technician should be

aware that this kit can cause system not to

operate.

4. Verify that the ERV (3) three phase blower motors are

phased sequentially ensuring correct rotation and

operation.

a. Disconnect power.

b. Reverse any two field power leads to the ERV.

c. Reapply power.

5. Verify that both blower motors are operating under

their full load AMP rating (FLA). The FLA can be found

on each motor and the unit nameplate

A - Re turn Damper Set tings

Manually adjust position of field installed dampers to

balance air flow.

B - Air Flow / Blower Speed Ad just ment

Blower speed selection is accomplished by changing the

sheave setting on both fresh air and exhaust air blowers.

To set ERV for the required air flow (CFM), the external

static pressure applied to the ERV (duct static) must be

known. See the CFM vs External Static Pressure chart for

the appropriate unit to determine the correct blower RPM

for the specified CFM and External Static Pressure.

After blower speed adjustments have been made. Ensure

that when the belt is replaced it is tensioned correctly. The

motor mounting plate can be adjusted to tension the belt. If

using a belt tension checker, adjust the span to the

appropriate setting and check the belt defection force. The

belt deflection force should be between 5-8 lbs or the

lowest tension at which the belt will not slip under peak load

conditions.

5. Disconnect main power to unit before making

adjustment to economizer and/or ERV unit.

6. Replace ERV control access cover.

7. Set thermostat to normal operating position.

8. Restore power to unit.

X - Main te nance

1. All motors use prelubricated sealed bearings; no

further lubrication is necessary.

2. Make visual inspection of motors, belts and wheel

rotating bearings during routine maintenance.

3. Eight pie-shaped segments, are seated on stops

between the segment retainer which pivots on the

wheel rim and secured to the hub and rim of wheel.

Annual inspection of the self cleaning wheel is

recommended. With power disconnected, remove

ERV access panels (rear) and unplug [J150 & P150]

(Refer to wiring diagram in this instruction

manual). Remove segment and wash with water

and/or mild detergent.

4. To install wheel segments follow steps A through E .

See Figure 3. Reverse procedure for segment

removal.

a. Unlock two segment retainers (one on each side of

the selected segment opening.

b. With the embedded stiffener facing the motor side,

insert the nose of the segment between the hub

plates.

c. Holding segment by the two outer corners, press

the segment towards the center of the wheel and

inwards against the spoke flanges. If hand

pressure does not fully seat the segment, insert

the flat tip of a screw driver between the wheel rim

and outer corners of the segment and apply

downward force while guiding the segment into

place.

PAGE 4

d. Close and latch each segment retainer under

segment retaining catch.

e. Slowly rotate the wheel 180

. Install the second

segment opposite the first for counterbalance.

Rotate the two installed segments 90

to balance

the wheel while the third segment is installed.

Rotate the wheel 180

again to install the fourth

segment opposite the third. Repeat this sequence

with the remaining four segments.

XI - Pul ley Kit In stal la tion

The units are shipped from the factory at the low static

setting. Pulley kits are available for the medium and high

static settings. To install a pulley kit.

1. Check content of pulley kit, if pulley kit contains:

a. An adjustable sheave and a fixed pitch pulley then

remove belt and both motor and blower pulley

b. An adjustable sheave then remove the motor

pulley.

c. A fixed pitch pulley then remove the blower pulley.

2. Replace pulley(s) with the pulley(s) from pulley kit.

Make sure each pulley is installed with a key. Tighten

the set screw on the pulley(s) to 100 in.lb.

3. Install the belt that came with the pulley kit. Tension

belt as explained in the blower speed adjustment

section.

4. Check the speed of the blower. Adjust the motor

sheave to increase or decrease the speed of the

blower. See blower adjustment section.

HUB

SEGMENT

FIGURE 3

SPOKE

SEGMENT RETAINER CATCH

WHEEL RIM

SEGMENT RETAINER

PAGE 5

Stand Alone ERV’S For Side by Side Duct Arrangements

Fea tures and Notes

1. Stand alone design allows higher levels of outdoor

air to be introduced into the a/c space.

2. Static test ports provided to verify intake and

exhaust CFM.

3. Balancing damper(s) is field provided when connected

to ductwork. System will not operate properly without

balancing damper.

4. Roof curbs are available for the ERV’s.

5. See blower performance charts for airflow at various

E.S.P..

6. Filter rack with 2” pleated filters included.

SUPPLY DUCT FLANGE OPENING

EXHAUST DUCT FLANGE OPENING

ERV Data Di men sional Data

Size CFM Range A B C D E F G H I J K

11 300-1100 44.75 32.13 33.50 11.00 27.00 4.00 4.25 2.88 2.50 20.75 14.38

20 1200-2000 54.38 37.25 37.50 12.00 30.00 1.63 5.13 4.06 1.63 20.75 17.50

28 1200-2800 52.25 42.62 43.56 14.00 32.00 8.69 5.25 4.25 2.88 20.75 25.50

36 2000-3600 60.00 46.69 57.37 16.50 39.50 12.00 5.50 4.05 5.88 20.75 25.50

46 3000-4600 60.00 52.69 57.37 16.50 39.50 12.00 8.69 5.50 5.88 20.75 28.06

62 4600-6200 72.00 70.88 63.63 19.50 39.50 17.53 14.50 8.70 6.60 20.75 37.75

Roof Curbs (Op tion Codes)

Size 14" 24"

11 CJ51-11 CJ52-11

20 CJ51-20 CJ52-20

28 CJ51-28 CJ52-28

36 CJ51-36 CJ52-36

46 CJ51-46 CJ52-46

62 CJ51-62 CJ52-62

PAGE 6

Notes:

1. Re move jumper to in stall field op tional low am bi ent switch.

2. Se lec tive volt age ter mi nal for proper unit volt age

3. Op tional low am bi ent switch.

4. Op tional mo tor ized in take damper.

5. Op tional Stop, Start and Jog Con trol (Cli mate Smart).

6. For en ergy man age ment sys tems con nect +24v to "G"

and com mon 24v to "C".

7. Op tional mo tor ized ex haust damper.

8. Op tional wheel ro ta tion sen sor.

9. Op tional smoke de tec tor.

S11-21-2ZERV

COMPONENT CODE

A131 Fixed Re lay Board

B26 Mo tor, Ex haust Air

B27 Mo tor, In take Air

B28 Mo tor, Desiccant Wheel

B30 Mo tor, Damper In take (Op tional)

B31 Mo tor, Damper Ex haust (Op tional)

C23 Ca pac i tor, Wheel Mo tor

C25 Ca pac i tor, Ex haust Air

C26 Ca pac i tor, In take Air

F29 Fuse

J48 Jack, Con trol Box (In take Air)

J50 Jack, Con trol Box (Wheel)

J51 Jack, Con trol Box (Ex haust Air)

J56 Jack, Con trol Box (Damper)

J148 Jack, In take Air Mo tor Har ness

P161 Plug, Damper Ex haust Mo tor Har ness

RS-1 Ro ta tion Sen sor (Op tional)

S26 Switch, Low Am bi ent (Op tional)

S51 Switch, Door

S52 Switch, Damper In take

S53 Switch, Damper Ex haust

SD Smoke De tec tor (Op tional)

SSJ Cli mate Smart Board (Op tional)

T27 Trans former, Con trol

T28 Trans former, Step-down (Op tional)

TB37 Ter mi nal Block (Low Volt age)

TB39 Ter mi nal Block (Mon i tor ing)

WHL Re lay, Wheel Mo tor

J150 Jack, Wheel Mo tor Har ness

J151 Jack, Ex haust Air Mo tor Har ness

J160 Jack, Damper In take Mo tor Har ness

J161 Jack, Damper Ex haust Mo tor Har ness

K163 Contactor, Ex haust Air Mo tor

K164 Contactor, In take Air Mo tor

MPD-1 Miss ing Pulse De tec tor Board (Op tional)

P48 Plug, In take Air Mo tor Har ness

P50 Plug, Wheel Mo tor Har ness

P51 Plug, Ex haust Air Mo tor Har ness

P56 Plug, Damper Mo tor Har ness

P148 Plug, In take Air Mo tor

P150 Plug, Wheel Mo tor

P151 Plug, Ex haust Air Mo tor

P160 Plug, Damper In take Mo tor Har ness

WIRE COLOR

CODE

BK Black

BL Blue

GR Green

GY Gray

OR Orange

PK Pink

RD Red

WT White

YL Yel low

PAGE 7

Unit#: 01-S11-02XX-21

Des ic cant Wheel for Roof top Unit

208- 230V (1 PH)

ERV UNIT WIR ING DIAGRAM

:setoN

.1 .hctiws tn ei bma wol lanoi tpo dleif llat sni ot repmuj evo meR

.2 eg atlov tinu reporp rof la ni mret eg atlov evi tce leS

.3 .hctiws tn ei bma wol lanoi tpO

.4 .repmad eka tni dez iro tom lanoi tpO

.5 .)tramS eta milC( lor tnoC goJ dna tratS ,potS lanoi tpO

.6 "G" ot v42+ tce nnoc sme tsys tne meg anam ygr ene roF

."C" ot v42 no mmoc dna

.7 .repmad tsua hxe dez iro tom lanoi tpO

.8 .ro snes noi ta tor leehw lanoi tpO

.9 .ro tce ted ekoms lanoi tpO

PAGE 8

Notes:

1. Re move jumper to in stall field op tional low am bi ent switch.

2. Step-down trans former as sem bly for 460/575 volt units.

3. Se lec tive volt age ter mi nal for proper unit volt age

4. Op tional low am bi ent switch.

5. Op tional mo tor ized in take damper.

6. Op tional Stop, Start and Jog Con trol (Cli mate Smart).

7. For en ergy man age ment sys tems con nect +24v to "G" and com mon 24v to "C".

8. Op tional mo tor ized ex haust damper.

9. Op tional wheel ro ta tion sen sor.

10. Op tional smoke de tec tor.

S11-S62-2ZERV

COMPONENT CODE

A131 Fixed Re lay Board

B26 Mo tor, Ex haust Air

B27 Mo tor, In take Air

B28 Mo tor, Des ic cant Wheel

B30 Mo tor, Damper In take (Op tional)

B31 Mo tor, Damper Ex haust (Op tional)

C23 Ca paci tor, Wheel Mo tor

F29 Fuse

J48 Jack, Con trol Box (In take Air)

J50 Jack, Con trol Box (Wheel)

J51 Jack, Con trol Box (Ex haust Air)

J56 Jack, Con trol Box (Damper)

J148 Jack, In take Air Mo tor Har ness

J150 Jack, Wheel Mo tor Har ness

J151 Jack, Ex haust Air Mo tor Har ness

P161 Plug, Damper Ex haust Mo tor Harness

RS-1 Ro ta tion Sen sor (Op tional)

S26 Switch, Low Am bi ent (Op tional)

S51 Switch, Door

S52 Switch, Damper Intake

S53 Switch, Damper Exhaust

SD Smoke De tec tor (Op tional)

SSJ Cli mate Smart Board (Op tional)

T27 Trans former, Con trol

T28 Trans former, Step- down (Op tional)

TB37 Ter mi nal Block (Low Volt age)

TB39 Ter mi nal Block (Mon i tor ing)

WHL Re lay, Wheel Motor

J152 Jack, Trans former (High Volt age)

J160 Jack, Damper In take Mo tor Har ness

J161 Jack, Damper Ex haust Mo tor Har ness

K163 Contactor, Ex haust Air Mo tor

K164 Contactor, In take Air Mo tor

MPD-1 Miss ing Pulse De tec tor Board (Op tional)

P48

Plug, In take Air Mo tor Har ness

P50

Plug, Wheel Mo tor Har ness

P51 Plug, Ex haust Air Mo tor Har ness

P56 Plug, Damper Mo tor Har ness

P148 Plug, In take Air Mo tor

P150 Plug, Wheel Mo tor

P151 Plug, Ex haust Air Mo tor

P152 Plug, Trans former (High Volt age)

P160 Plug, Damper In take Mo tor Harness

WIRE COLOR

CODE

BK Black

BL Blue

GR Green

GY Gray

OR Orange

PK Pink

RD Red

WT White

YL Yel low

PAGE 9

Unit#: 01-S11-S62-02XX-23 thru -43

Des ic cant Wheel for Roof top Unit

208- 230/460/575V (3 PH)

ERV UNIT WIR ING DIAGRAM

:setoN

.1 .hctiws tn ei bma wol lanoi tpo dleif llat sni ot repmuj evo meR

.2 .stinu tlov 575/064 rof yl bme ssa remro fsnart nwod-petS

.3 eg atlov tinu reporp rof la ni mret eg atlov evi tce leS

.4 .hctiws tn ei bma wol lanoi tpO

.5 .repmad eka tni dez iro tom lanoi tpO

.6 .)tramS eta milC( lor tnoC goJ dna tratS ,potS lanoi tpO

.7 ."C" ot v42 no mmoc dna "G" ot v42+ tce nnoc sme tsys tne meg anam ygr ene roF

.8 .repmad tsua hxe dez iro tom lanoi tpO

.9 .ro snes noi ta tor leehw lanoi tpO

.01 .ro tce ted ekoms lanoi tpO

PAGE 10

Mist Elimi na tor Fil ter in In take Hood (2HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

1200 1065 1285 1375 1415 1495 1580 1685

1400 1140 1330 1410 1440 1555 1660 1760

1600 1290 1400 1480 1545 1670 1745 1835

1800 1395 1470 1540 1665 1735 1800 1880

2000 1460 1530 1650 1725 1795 1870 1960

Ba ro met ric Hood, 2" Pleated Fil ters (2HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

1200 1175 1290 1430 1520 1680 1765 1850

1400 1245 1425 1515 1675 1755 1830 1920

1600 1400 1505 1670 1750 1825 1910 1980

1800 1495 1660 1740 1820 1900 1975 2090

2000 1645 1730 1815 1895 1965 2080 2170

SUP PLY

Blower RPM for XBWS20-AQ20

EXHAUST

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

RPM Range

Low 1000- 1300 Stan dard Unit

Me dium 1300- 1750 Op tional Kit

High 1750- 2200 Op tional Kit

SUP PLY

Blower RPM for XBWS11-AQ20

EXHAUST

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

RPM Range

Low 1000- 1300 Stan dard Unit

Me dium 1300- 1700 Op tional Kit

High 1750-2200 Op tional Kit

Ba ro met ric Hood, 2" Pleated Fil ters (1.5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

300 N/A N/A 1150 1285 1415 1515 1640

500 N/A 1145 1275 1410 1510 1545 1720

700 1140 1270 1405 1505 1590 1715 1815

900 1320 1435 1585 1665 1705 1810 1930

1100 1495 1580 1660 1755 1880 N/A N/A

Mist Elimi na tor Fil ter in In take Hood (1.5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

300 N/A N/A 1020 1205 1365 1480 1590

500 N/A 1015 1200 1320 1460 1565 1670

700 990 1190 1315 1455 1560 1665 1715

900 1150 1310 1450 1555 1660 1680 1795

1100 1305 1440 1550 1655 1740 1815 1895

PAGE 11

Mist Elimi na tor Fil ter in In take Hood (3HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

2000 815 925 1020 1105 1155 1255 1325

2400 920 1060 1130 1215 1250 1355 1385

2800 1010 1140 1240 1285 1370 1425 1470

3200 1125 1235 1340 1385 1455 1465 N/A

3600 1225 1375 1440 1460 1500 N/A N/A

Ba ro met ric Hood, 2" Pleated Fil ters (3HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

2000 755 890 970 1060 1125 1215 1280

2400 985 1035 1085 1140 1240 1275 1325

2800 1020 1115 1175 1230 1270 1335 1370

3200 1105 1200 1225 1285 1300 1390 1430

3600 1155 1265 1295 1335 1385 N/A N/A

SUP PLY

Blower RPM for XBWS36-AQ20

EXHAUST

RPM Range

Low 700-1025 Stan dard Unit

Me dium 1030-1305 Op tional Kit

High 1325-1575 Op tional Kit

SUP PLY

Blower RPM for XBWS28-AQ20

EXHAUST

RPM Range

Low 950-1320 Stan dard Unit

Me dium 1325-1565 Op tional Kit

High 1570-1880 Op tional Kit

Mist Elimi na tor Fil ter in In take Hood (3HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

1200 N/A 955 1070 1210 1370 1465 1550

1600 N/A 1065 1205 1305 1460 1540 1595

2000 1060 1200 1290 1445 1530 1585 1680

2400 1190 1335 1440 1490 1575 1670 1755

2800 1300 1460 1550 1645 1705 1750 1800

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

Ba ro met ric Hood, 2" Pleated Fil ters (3HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

1200 N/A N/A 1025 1170 1270 1355 1400

1600 N/A 1020 1155 1240 1330 1390 1490

2000 1015 1150 1235 1325 1380 1475 1590

2400 1140 1285 1365 1420 1510 1595 1640

2800 1280 1345 1455 1540 1575 1670 1745

PAGE 12

Mist Elimi na tor Fil ter in In take Hood (5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

4600 795 900 1030 1075 1160 1220 1255

5000 855 920 1070 1130 1190 1250 1275

5400 880 950 1095 1155 1245 1270 1290

5800 915 1035 1115 1175 1255 1280 N/A

6200 985 1080 1135 1225 1265 N/A N/A

Ba ro met ric Hood, 2" Pleated Fil ters (5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

4600 705 885 985 1045 1100 1155 1215

5000 825 950 1025 1095 1150 1210 1245

5400 875 980 1080 1140 1190 1240 1275

5800 935 995 1130 1180 1230 N/A N/A

6200 985 1095 1165 N/A N/A N/A N/A

SUP PLY

Blower RPM for XBW62S-AQ20

EXHAUST

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

RPM Range

Low 700-900 Stan dard Unit

Me dium 900-1100 Op tional Kit

High 1100-1300 Op tional Kit

SUP PLY

Blower RPM for XBWS46-AQ20

EXHAUST

Notes:

1. Drive losses included in the above tables.

2. Performance can vary depending on ambient conditions

3. Blower RPMs are for reference only

RPM Range

Low 780- 1020 Stan dard Unit

Me dium 1000- 1315 Op tional Kit

High 1315- 1700 Op tional Kit

Mist Elimi na tor Fil ter in In take Hood (5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

3000 965 1085 1150 1230 1295 1345 1420

3400 1035 1145 1250 1290 1335 1415 1475

3800 1120 1245 1285 1315 1440 1470 1535

4200 1215 1305 1355 1430 1465 1530 1595

4600 1300 1375 1450 1460 1540 1590 1650

Ba ro met ric Hood, 2" Pleated Fil ters (5HP)

Ex ter nal Static Pres sure (in wa ter)

0 0.25 0.5 0.75 1 1.25 1.5

CFM

3000 1010 1105 1195 1255 1300 1375 1415

3400 1100 1190 1250 1320 1370 1410 1480

3800 1185 1245 1360 1410 1440 1475 1540

4200 1240 1355 1425 1465 1530 1590 1630

4600 1345 1410 1485 1520 1585 1650 1700

PAGE 13

Notes

PAGE 14

Notes

PAGE 15

Notes

START UP INFORMATION SHEET

VOLTAGE - ERV UNIT

In com ing Volt age L1-L2 L1-L3 L2-L3

Run ning Volt age L1-L2 L 1-L3 L2-L3

Sec ond ary Volt age C (black) to G (green) Volts*

C (black) to W (white) Volts*

* With ther mo stat call ing.

AM PER AGE - ERV MO TORS

In take Mo tor: Nom i nal HP Rated Amps Run ning Amps

Ex haust Mo tor: Nom i nal HP Rated Amps Run ning Amps

Wheel Mo tor: Nom i nal HP Rated Amps Run ning Amps

AIR FLOW

In take De sign CFM Pres sure Drop Cal cu lated CFM

Ex haust De sign CFM Pres sure Drop Cal cu lated CFM

Amb. db Temp Re turn Air db Temp* Tem pered Air db Temp*

Amb. wb Temp Re turn Air wb Temp* Tem pered Air wbTemp*

* Mea sure af ter 15 min utes of run time

IN STAL LA TION CHECK LIST

ERV Model # Se rial #

Owner Owner Phone #

Owner Ad dress

In stall ing Con trac tor Start Up Me chanic

q Inspect the unit for transit damage and report any damage on the carrier’s freight bill.

q Check model number to insure it matches the job requirements.

q Install field accessories and unit adapter panels as required. Follow accessory and unit installation manuals.

q Verify field wiring, including the wiring to any accessories.

q Check all multi-tap transformers, to insure they are set to the proper incoming voltage.

q Verify correct belt tension, as well as the belt/pulley alignment. Tighten if needed.

q Prior to energizing the unit, inspect all the electrical connections.

q Power the unit. Bump the motor contactor to check rotation. Three phase motors are synchronized at the

factory. If blower motor fans are running backwards, de-energize power to the unit, then swap two of the three

incoming electrical lines to obtain proper phasing. Re-check.

q Perform all start up procedures outlined in the installation manual shipped with the unit.

q Fill in the Start Up Information as outlined on the opposite side of this sheet.

q Provide owner with information packet. Explain the thermostat and unit operation.

1-800-695-1901; www.ReznorHVAC.com

Reznor® is registered in at least the United States.

All other marks are the property of their respective organizations.

Reznor XBWS Installation guide

Brand: Reznor

Model: XBWS

Category: Air filters

Type: Installation guide

Download PDF

report

Reznor XBWS Installation guide

Reznor XBWS Installation guide

Related papers

Other documents