Digimerge DND13TL2 User manual

www.digimerge.com

Instruction Manual

English Version 2.0

Syncro-V

Client Software for SyncroIP Series Cameras

www.flir.com/security

formerly

i

TABLE OF CONTENTS

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Adding IP cameras over the local area network (LAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Adding remote IP cameras to Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Using the System Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Display window controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Cycle List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Creating Cycle Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cycle List controls overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting up Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the camera date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Syncing camera time with an NTP server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Syncing the camera date and time to your computer clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Set the date and time manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Selecting recording storage locations for Syncro-V . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Configuring hard disk recording for Syncro-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Configuring NAS recording for Syncro-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configuring recording parameters and starting the recording service . . . . . . . . . . . . . 20

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Record Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Searching for video using Local Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Record Playback overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Adding/removing search directories for Local Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Remote Playback (playing back video from microSD or SD card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

FTP Record Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Searching for video using FTP Record Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Backing up video files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Backup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Changing the backup folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Alarm Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Searching for alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Alarm types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Device Manager (configuring cameras) . . . . . . . . . . . . . . . . . . . . . . 37

Device Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Deleting cameras from Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Device Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

ii

Changing the Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Login In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Configuring Stream settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Device Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Enabling Static IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Enabling DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Device Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Changing ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

BNC Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

External Device (not supported) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Alarm Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Motion Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Enabling Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Configuring Motion Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Disk Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Local Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Record Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Record Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Formatting the microSD/SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Configuring FTP storage locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Configuring NAS storage locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

CMS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

SMTP (Enabling Email Alerts) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Network Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Finding the camera’s IP address using UPnP in Windows® 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Bonjour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Finding the camera’s IP address using Bonjour® in Mac OS® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Privacy Masking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Creating privacy mask areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Deleting privacy mask areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Device Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Device Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

System Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Video Display and Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Adding User Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Deleting User Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

iii

Modifying User Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Adding user accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Deleting user accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Modifying user accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Unlocking user accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Configuring Camera Sensor Settings . . . . . . . . . . . . . . . . . . . . . . . . 75

Image Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Shutter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Gain Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

DayNightMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Gamma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

WDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

AE Meter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

WB Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Noise Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

iv

1

Getting Started

GETTING STARTED

System requirements

Before installation, make sure your system meets or exceeds the following requirements.

Please note that increasing the number of cameras increases the computing and bandwidth

requirements.

Minimum Specification

CPU Core 2 Quad 2.4 GHz or higher

RAM 4 GB or higher

Video Card

1

1. Make sure to install video card drivers provided by the manufacturer.

DirectX® 9.0 compatible video card

NVIDIA GeForce 9500GT or higher; 512 MB video memory or higher

Network

2

2. If using IPv6, Windows® 7 is recommended.

1 Gigabit internal network recommended (inc

luding NIC, router/switch, and Cat 5e or higher

RJ45 cabling)

512 MB or higher upload speed for remote connections

HDD 1 GB free, excluding space required for recording

E-IDE, PATA, SATA, SCSI, SAS (7200 RPM or faster). Separate Ph

ysical HDD for r

ecordings

using more than 8 cameras

3

3. If you have 16 or more cameras, it is recommended to balance recordings between separate hard

drives. RAID system recommended.

Operating

System

4

4. Software runs in 32-bit operation on 64-bit systems.

Windows® Vista Business, Enterprise, or Ultimate (32 bit or 64 bit)

W

indows® 7 Professional, Enterprise, or Ultimate (32 bit or 64 bit)

Windows® Server 2003 (32 bit or 64 bit), Windows® Server 2008 R1/R2 (32 bi

t or 64 bit)

Installation

Install Syncro-V software from the CD included with your IP camera or by downloading it from

www.digimerge.com. It is recommended to visit www.digimerge.com for the latest software

versions.

Before you begin:

Make sure your IP cameras are connected to the same local network as

the computer where you are installing the Syncro-V software.

2

Getting Started

Adding IP cameras over the local area network (LAN)

1. Double-click the Syncro-V icon ( ) on the Desktop. The log in screen appears.

2. Under User Name and Password, enter the default admin username (admin) and

password (admin). Click Login.

Enter Admin

Click Login

NOTE: If a user account other than admin enters the wrong password more than 3 times,

they are locked out. To unlock a user account, see “Unlocking user accounts” on page 74.

3. Syncro-V opens and scans the local area network for connected cameras. Detected

camera IP addresses (or Device Names) appear in the Device List on the left side of the

screen with a icon.

Found camera IP address

NOTE: The camera found icon ( ) and connected camera ( ) icons are only used for

cameras in the local area network (LAN). A icon is shown for all cameras outside of

the LAN. This does not affect your ab

ility to connect to the camera remotely.

4. Click on a camera IP address in Device List to

login.

3

Getting Started

5. Under User Name and Password, enter the User Name and Password for the

camera and click Continue.

NOTE: For SyncroIP Series cameras, the default User Name is admin and the default

password is admin.

Enter the User Name and

Password for the camera

Click Continue to login

• Check Use for default login config to allow Syncro-V to automatically enter this user

name and password when connecting to other cameras.

6. The camera appears under the camera IP address. Click and drag the camera to the

display grid to open it.

Click and drag the camera to the

display grid to open it

7. Repeat steps 4-6 for any additional cameras you would like to connect.

Adding remote IP cameras to Device List

You can add remote IP cameras to the Device List to connect over the Internet.

4

Getting Started

To add remote IP cameras to device list:

Before adding remote cameras, make sure you have performed the

following:

• Port forwarded the IP camera’s control port on your router.

• If you are adding multiple cameras from the same LAN, they cannot

share the same control port. Configure a different control port for each

camera and port forward the newly selected ports. To change camera

ports, see “Device Port” on page 43.

• Set up your IP cameras for FLIR’s free DDNS service. See the SyncroIP

Series Quick Start Guide for details.

1. Click Device Manager > Video Device Manager.

2. Click Manager. The Device Maintenance window opens.

Click Add Click Save

Enter the camera IP

or DDNS address

Enter a Device

Name

Enter the camera

control port

3. Under Device IP, enter the camera’s IP address or DDNS address. If using a DDNS

address, enter the Domain Name from the confirmation email. For example, if the

Domain Name is tomsmith.myddns-flir.com, enter tomsmith.myddns-flir.com.

4. Under Contro

l Port, enter the camera’s control port.

5. (Optional) Under Device Name, enter a name for the IP camera that will appear in Device

List.

6. Click Add to add the camera to the Device List.

7. Click Save to save changes. Click OK.

5

Getting Started

8. Close all windows to return to the Live Video screen. The newly added camera will appear

in Device List.

Added camera

NOTE: A icon is shown for all cameras outside of the LAN. This does not affect your

ability to connect to the camera re

motely.

9. Click on the camera in Device List to lo

gin. Enter the User Name and Password and click

Continue.

Enter the User Name and

Password for the camera

Click Continue to login

10.Click and drag the camera to a display grid screen to open it.

Click and drag the camera to

the display grid to open it

NOTE: It is recommended to select stream2 when remotely connecting to cameras. To

select stream2, click

, select stream2 under Stream, and click Apply then OK. Stream2

has a lower resolution for improved performance when less bandwidth is available.

6

Using the System Interface

USING THE SYSTEM INTERFACE

The system interface allows you to watch live video from your IP cameras, program your

camera settings, set up recording, and watch recorded video. By default, the system interface

opens in Live Video Mode.

Overview

1. Live Video: Watch live video from your IP cameras.

2. Playback: Search for and playback recorded video. See “Playback” on page 25.

3. Backup: Perform backup functions. See “Backup” on page 32.

4. Alarm Manager: Configure alarm settings. See “Alarm Manager” on page 35.

5. Device Manager: Configure settings for cameras in Device List. See “Device Manager

(configuring cameras)” on page 37.

6. System Manager: Configure settings for Syncr

o-V software. See “System Manager” on

page 65.

7. Lock : Click to Lock Syncro-V. Enter your password and click Unlock.

11

10

9

1 2 3

12

13

14

15

16

4

5 6

Tip: Hold the mouse over buttons to see their function.

7

8

7

Using the System Interface

8. Multi-monitor Controls: Requires multiple monitors. Click , , or to

create a new display screen. Click to move new display screen to a secondary

monitor, and click to return the display screen to the primary monitor. Click the X on

a display screen to close.

9. Select Device List/Cycle List :

• : Open Device List.

• : Open Cycle List. Cycle List allows you to configure custom camera cycles. See

“Cycle List” on page 9.

10.Device List: Select and organize cameras.

11.Voice Buttons:

• : Click to activate the intercom to the camera (speaker required).

• : Click to configure settings for computer microphone.

12.Display Area: Shows video from your IP cameras. For details, see “Display window

controls” on page 9.

13.Control Buttons : Controls for the selected camera.

• : Select a camera in Device List, then click to open in the selected window.

• : Click to disconnect from the camera in the selected window.

• : Select Single Snapshot to take a snapshot of live video from the selected camera.

Then click Save to save the snapshot to the Snapshot directory.

• Select Sequence Snapshot to save a series of snapshots to the Snapshot

directory.

• Select Snapshot Dire

ctory to open the Snapshot directory.

• Select Snapshot Settings to configure snapshot settings.

Select Snapshot directory

Set parameters for Sequence Snapshot:

Time: Total duration of Sequence

Period: Time between snapshots

Select file format for snapshots (.jpg or .bmp)

Click to Save

8

Using the System Interface

• : Click to select the video stream for the selected camera. You can configure the camera

streams using Device Manager.

• : Click to open the selected camera in full-screen. Press ESC to exit full-screen.

• : Click to hide/un-hide video info for selected camera.

14.Spilt-screen Selectors : Controls for the selected display screen.

• : Click to open selected camera in single-window view.

• : Click for 4-way-split.

• : Click for 8-way-split, with 1 large window and 7 small windows.

• : Click for 9-way-split.

• : Click for 16-way-split.

• : Click for 36-way-split.

• : Click to open display in full-screen. Press ESC to exit full-screen.

• : Click to hide/un-hide video info for all cameras.

15.Save/Resume Layout

: Select Save Layout to save the current screen layout.

Select Resume Layout to open the saved layout. Only 1 layout may be saved at a time.

16.Volume Controls:

Click to mute/

un-mute volume

Click to adjust volume

Select camera stream

Click to save

Stream information

9

Using the System Interface

Display window controls

Use the following controls

Right-click on video to

open sub-menu

PTZ Control

On/Off

Record On/Off

Audio On/Off

Close Video

Camera Device Name or IP Address

Video Information

while viewing live video:

• Double-click on window to open video in a single display area.

• Click inside window and use the scroll wheel to zoom in and out on the center of the image.

Right-click inside window and click Restore Panorama to return to default zoom.

• Click and drag inside video to zoom in on a specific area. Right-click inside window and

click Restore Panorama to return to default zoom.

• PTZ Control On/Off: Double-click to turn PTZ controls on/off. Icon is green ( ) when

PTZ controls are on; it is blue ( ) when PTZ controls are off.

• Record On/Off: Double-click to turn recording on/off. Recording icon is shown with a

green circle ( ) when recording is on; it is shown without the circle ( ) when recording

is off.

NOTE: Record

ing must be configured for Syncro-V and each camera before it can record.

To configure recording, see “Setting up Recording” on page 14.

• Audio On/Off: Double-click to turn listen-in audio on or off.

• Close Video: Click to Close Video in the selected display area.

Cycle List

The Cycle List allows you to create custom camera display cycles. Camera display cycles

automatically change the cameras displayed on screen.

To access Cycle List:

• Click to open Cycle List.

10

Using the System Interface

Creating Cycle Groups

Cycle Groups determine the order and arrangement of cameras shown in a cycle.

Cycle Groups are organized in screens. Cameras are assigned to screens, and each screen

is shown on screen for a predetermined interval before changing to the next screen. In the

example below, there are 5 screens shown in the Cycle Group and the Interval is set to 10

seconds.

In this example, when the cycle is run, the cameras in screen 1 will be shown for 10 seconds,

then the cameras in screen 2 will be shown for 10 seconds, etc.

11

Using the System Interface

To create a Cycle Group:

Right-click and select

Create Cycle Group

1. Right-click Cycle List and select Create

Cycle Group.

2. Enter a name for the Cycle Group and

click outside the Cycle Group name.

3. Right-click the new Cycle Group and

select Conf

ig Cycle Group.The Cycle

Configure menu opens.

4. Under Display, select the number of

cameras you would like to display in a

screen at one time. No

te that, after

adding cameras to a Cycle Group,

changing the Display value will remove all

cameras from the Cycle Group.

5. Under Interval, enter the number of

seconds that screens will be shown before changing.

6. Check cameras you want to add to the Cycle Group in Device List and click to add

them to the Cycle Group.

Check cameras to select

Click to add selected

cameras to Cycle Group

12

Using the System Interface

7. Arrange the cameras into screens as needed. Click + to add a new screen. Click and drag

cameras to move them between screens. Click a screen and click and to change

the order of screens shown.

Add screen

Delete screen

Move screen up

Move screen down

Click Save

8. Click Save to save the Cycle Group. To start a

cycle, click the Cycle Group in the Cycle List and

click .

Click the Cycle

Group

Click to Start

Cycle

13

Using the System Interface

Cycle List controls overview

Play/pause

selected cycle

Stop cycle

New Cycle

Group

Delete Cycle

Group

Configure

Cycle Group

Screens

Cameras

14

Setting up Recording

SETTING UP RECORDING

To set up recording for your IP cameras, you must do the following:

1. Set the camera date and time for each camera.

2. Select a storage location for recordings.

3. Configure recording parameters for each camera and start the recording service.

Setting the camera date and time

You can set the camera date and time the following ways:

• Sync the camera date and time to an NTP time server.

• Sync the camera date and time to your computer clock.

• Manually set the date and time.

Syncing camera time with an NTP server

The cameras are set to connect to an NTP server by default, but you must select your time

zone and enable Daylight Savings Time, if required, to ensure accurate time.

To configure the date and time using NTP:

1. Click Device Manager > Video Device Management. Then click the camera you wish

to configure in Device List.

2. Click Device Hardware > Date and Time.

3. Under Time Zone, select your time zone.

4. If your region observes Daylight Savings Time, check Adjust clock for daylight saving

changes. Adjust the Start and End times for Daylight Savings time as necessary.

It is highly recommended to set the date and time on each camera before

setting up recording. Recording time stamps are created based on the time set

on the camera, not the time shown in Syncro-V or your computer clock.

Page is loading ...

Digimerge DND13TL2 User manual

This manual is also suitable for

Digimerge DND13TL2 User manual

Related papers

Other documents