JVC DS-TP330 Owner's manual

Brand: JVC

Model: DS-TP330

Category: AV receivers

Type: Owner's manual

This manual is also suitable for

AUDIO/VIDEO CONTROL RECEIVER

RX-6000VBK / RX-6008VBK

3D-pJ.IONIC

DDF_-_

DIGITAL

SURROUND

AI_I'I'tlIIIDI I I IAliLr

i'IIW _vlrlkg B=llBVJfl

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

LVT0380-001A

[J]

RX-6000VBK/RX-6008VBK[J]/

RX-6500VBK[J]

Errata Sheet

Please notice the following modifications when reading Instructions.

Page 18.

Incorrect

Notes:

If "REAR SPK" and "CENTER SPK" are set to "NONE,"

-- you can select only "HEAD PHONE" or "OFF" for the DSP mode.

-- you cannot select Surround mode.

No sounds come out of the center speaker, even flit is connected.

Correct

Notes:

If"REAR SPK" and "CENTER SPK" aFe set to "NONE," VOUcannot

select Surround mode.

No sounds come out of the center speaker, even flit is connected.

When "REAR SPK" and "CENTER SPK" are set to "NONE," the

same effect as used for the 3D-PHONIC is applied to any DAP

mode to maintain the surround elements with only two front

speakers.

Page 20.

On page 20, in the DSP mode cycle it is written that "3D ACTION" will be selected after "HEAD PHONE,"

but the order has been changed so that "3D ACTION" wilI be selected before "HEAD PHONE."

Warnings, Cautions and Others

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol,

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

liaU'oin°:ec_-tPOWmEaiRsSpiltulghloshut the power off completely. The I

POWER switch in any position does not disconnect the mains line. I

The power can be remote controlled. |

For U.S.A.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules,

These limits are designed to provide reasonable protection against

harmful interference in a residential installation,

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

Caution: Proper Ventilation

To avoide risk of electric shock and fire and to protect from damage.

Locate the apparatus as follows:

Front: No obstructions open spacing.

Sides: No obstructions in 10 cm from the sides.

Top: No obstructions in 10 cm from the top.

Back: No obstructions in 15 cm from the back

Bottom: Place on the level surface.

In addition, maintain the best possible air circulation as illustrated.

,'///////////_

Wall orobstructions

Spacing 15cm or more

i I

Floor

Front

Stand height 15 cm or more

G-1

Table of Contents

Parts Identification ...................................... 2

Getting Started ........................................... :3

Before installation ...................................................................... 3

Checking the Supplied Accessories ........................................... 3

Connecting the FM and AM Antennas ....................................... 3

Connecting the Speakers ............................................................ 4

Connecting Audio/Video Components ....................................... 5

Connecting the Power Cord ....................................................... 7

Putting Batteries in the Remote Control .................................... 7

Basic Operations ......................................... 8

_l_rning the Power On and OFF(Standby) .................................. 8

Selecting the Source to Play ....................................................... 8

Adjusting the Volume ................................................................. 9

Selecting the Front Speakers ...................................................... 9

Muting the Sound ....................................................................... 9

Adjusting the Subwoofer Output Level .................................... 10

Attenuating the input Signal .................................................... 10

Reinforcing the Bass ................................................................ l0

Adjusting the 'lone ................................................................... 10

Basic Settings ........................................... 1 1

Recording a Source ....................................................................

Adjusting the Front Speaker Output Balance ........................... 11

Setting the Subwoofer information .......................................... 1l

Changing the Sot_rce Name ...................................................... I 1

Setting the Speakers for _he DSP Modes ................................. 12

Digital Input (DIGITAL IN) Terminal Setting ......................... 14

Selecting the Analog or Digital input Mode ............................ 14

Storing the Basic Settings and Adjustments

.............One 'l_t_ch Operation .................................................... 15

Using the Sleep Timer .............................................................. 15

Receiving Radio Broadcasts ........................ 1 6

_l_ning in Stations Manually .................................................... 16

Using Preset Tuning ................................................................. 16

Selecting the FM Reception Mode ........................................... 17

Using the DSP Modes ................................ 18

Available DSP Modes According to the Speaker Arrangement.. 20

Adjusting the 3D-PHONIC Modes .......................................... 21

Adjusting the DAP Modes and Headphones mode .................. 21

Adjusting the Stlrround Modes ................................................ 22

Activating the DSP Modes ....................................................... 25

COMPU LINK Remote Control System ......... 26

AV COMPU LINK Remote Control System .... 27

Operating JVC's Audio/Video Components ... 29

Troubleshooting ......................................... 31

Specifications ............................................ 32

l Parts Identification

Become familiar with the buttons and controls on the receiver before use.

Refer to the pages in parentheses for details.

½____J

t)I) t

.IVn

Front Panel Remote Control

POWER bullor_and STANDBY lamp (8) _ POWER buttons (8, 30)

SOURCE NAME (TV SOUNDiDBS) button TV, VCR, AUDIO

(1I) _ SLEEP button (I5)

O Display(8) O SURROUNDbuttor_(25)

O ONETOUCHOPER/krION/INPUTA'ET. O SURROUND MODE button (21)

buttor_(15) O SOUND button (21)

O DSP MODE button (21) O TViVIDEO button (30)

O SURROUNDbuttonandlamp(25) _ CD-DISCbuttor_(29)

Remote sensor (7) O Soulce selecfir_g bul{or_s(8)

O ADJUST button (10) * DVD, TV SOUN D!DBS, VCR, CD, 3APE/MD,

O SETIINGbullon(12 14)* PHONO, FM/AM

MASTER VOLUME controt (9) O TV VOL +¢ buttons (30)

MEMORY button (I6) _ TV CH +_ buttor_s(30)

MUEFICURSORbu_*or_s _ • 10keys for selectir_g preset charmel (17)

ANAEOG/D[GflAL buttor_ and DIGI'IS,kE • 10keys for adjusting sound (22 24, 29)

AUTO lamp (14) • 10keys foroperatingaudio/videocomponents

Soul_e selecting bullolts (8) (29, 30)

DVD, TV SOUND!DBS, VCR, CD,'IAPE!MD, _ ANALOG/DIGI'IAL bullolt (14)

PHONO, EMiAM * _ MUTING buttor_ (9)

SOURCE NAME (TAPE/MD) bullon _ VOLUME -_/ bullolts (9)

(8, 11, 14) _ Operating buttons for audio/video colr_ponents

SPEAKERS 1/2bullons (9) (29,30)

PHONES jack (9)

IMPORTANT:

'lb use the MULTI CURSOR buttons ('12) on the front panel:

What these buttons actually do depends on which function you are trying to adjust. Before using these buttons, select the function by

pressing one of the buttons marked with *.

l Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the

power supply.

I:]_It'rJ'_ II'i'g_i_ IffI!'t'_

General

• Be sure your hands are dry.

• Turn the power offto all components.

• Read the manuals supplied with the components you are going to

connect.

Locations

• Install the receiver in a location that is level and protected from

moisture.

• The temperature around the receiver must be between 5°C and

35°C (23°F and 95°F).

• Make sure there is good ventilation around the receiver. Poor

ventilation could cause overheating and damage the receiver.

Handling the receiver

• Do not insert any metal obiect into the receiver.

• Do not disassemble the receiver or remove screws, covers, or

cabinet.

• Do not expose the receiver to rain or moisture.

Check to be sure you have all of the following items, which are

supplied with the receiver.

The number in the parentheses indicates the quantity of the pieces

supplied.

• Remote Control (1)

• Batteries (2)

• AM Loop Antenna (1)

• FM Antenna (1)

If anything is missing, contact your dealer immediately.

FM Antenna Connections

A B

FM Antenna

Extend the supplied FM antenna horizontally.

Outdoor FM Antenna Cable

EXT

A. Using a Supplied FM Antenna

The FM antenna provided can be connected to the FM 75_

COAXIAL telTainal as tempora W measure.

B. Using a Standard Type Connector (Not Supplied)

A standard type connector should be connected to the FM 75f2

COAXIAL tenTainal.

Note:

If reception is poor, connect an outdoor antenna.

Before attaching a 75£2coaxial cable (the kind with a round wire going

to an outdoor antenna), disconnect the supplied FM antenna.

AM Antenna Connections

ANTENNA--

FM75Z2

Snap the tabs on the loop flame

into the slots of the base to

assemble the AM loop.

Basic connecting procedure

1 2 3

(not supplied)

Cut, twist and remove the insulation at the end of

each speaker signal cable (not supplied).

Open the terminal and then insert the speaker

signal cable.

Close the terminal.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT

SPEAKERS ,1) terminals, and another pair to the FRONT

SPEAKERS, : term nals).

Right speaker FRONT SPEAKERS (1) Left speaker

Turn the loop antenna until you have the best reception.

Notes:

• Make sure the antenna conductors do not touch any other

terminals, connecting cords and power cord. This could cause poor

reception.

• If reception is poor, connect an outdoor single vinyl-covered wire to

the AM EXT terminal. (Keep the AM loop antenna connected.)

You can connect the following speakers:

• Two pairs of fiont speakers to produce normal stereo sound.

• One pair of rear speakers to enjoy the surround effect.

• One center speaker to produce more effective surround effect (to

emphasize human voices).

• One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker

setting intbrmation properly to obtain the best possible DSP

effect. Vor details, see page 12.

For each speaker (except for a subwoofer), connect the () and (+)

terminals on the rear panel to the () and (+) terminals marked on

the speakers. For connecting a subwoofer, see page 5.

- FRONTSPEAKERS

Right speaker FRONTSPEAKERS, , Left speaker

Connecting the rear and center speakers

Connect real- speakers to the P,EAP, SPEAKERS terminals and a

center speaker to the CENTER SPEAKER terminals.

Center speaker

Left rear Right rear

speaker speaker

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the

speaker terminals.

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer.

Connect the input jack of a powered suhwoofer to the

SUBWOOFER OUT jack on the rear panel, using a cable with RCA

pin plugs (not supplied).

A •

Powered subwoofer

You can connect the following audio/video components to this

receiver. Refer also to the manuals supplied with your components.

Audio Components

• CD player*

• Turntable

• Cassette deck

or MD recorder*

Video Components

• DVD player*

• TV

• DBS tuner*

• VCR

* You can connect these components using the methods described

in "Analog connections" (below) or in "Digital connections" (see

page 7).

Analog connections

Audio component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the

audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer

between the source components and this receiver, the sound output

through this receiver may be distorted.

I Turntable ]

Turntable

If an earth cable is provided for

your turntable, connect the cable

to the terminal marked (r_) of the

ANTENNA terminals on the rear

panel.

Note:

Any turntables incorporating a small-output cartridge such as an MC

(moving-coil type) must be connected to this receiver through a

commercial head amplifier or step-up transformer. Direct connection

may result in insufficient volume.

Cassette deck or MD recorder

Cassette deck

To audio input

To audio output

CD player

To audio output

® ®,N

!pLAY)

I RIGHT LEFT

MD recorder

Note:

YOU can connect either a cassette deck or an MD recorder to the

TAPE/MD jac_s. When connecting an MD recorder to the TAPE/MD

jacks, change the source name, which wil! be shown on the display

when selected as the source, to "M D."See page 1! for details.

If your audio components have a COMPU LINK-3 terminal

See also page 26 for detailed information about the connection and

the COMI U LINK_3 remote control system.

Video component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the

audio right jack, and the yellow plug to the video jack.

IMPORTANT:

This receiver is equipped with both the composite video and S-video

input terminals for the DVD player connection.

You do not have to connect both the composite video and S-video

terminals.

However', remember that the video signals from the composite

video input terminal are output only through the composite

video output terminals, while the ones from the S-video input

terminal are output only through the S-video output terminal.

Therefore, if your" DVD player is connected to the receiver only

through the S-video input terminaI, you cannot record the picture

from the DVD player on the VCR.

In addition, if the TV and the DVD pIayer are connected to the

receiver through the different video terminals, you cannot view the

playback picture from the DVD player on the TV.

I DVDplayer

"IVand/or DBStuner

When connecting the TV to the TV SOUND/DBS jacks, DO NOT

connect the TV's v dee output to the vdee nput term na .

To S-video input (for better

Connect the TV to the MONITOR

OUT jack to view the playback

picture from the other connected

video components.

IA} To front left/right channel audio output (or to audio mixed

output if necessary)

To composite video output

To S-video output (for better playback picture quality)

VCR

[]

Inl IIIIII

IAI To left/right channel audio output

To left/right channel audio input

To composite video output

To composite video input

To audio

output

[]

DBS tuner

To composite video output

Note:

When connecting the DBS tuner to the TVSOUND/DBSjacks,

change the source name, which will be shown on the display when

selected as the source, to "DBS."See page ! 1fordetails.

If your audio components have an AV COMPU LINK terminal

See also page 27 for detailed information about the connection and

the AV COMPU LINK remote control system.

Digital connections

This receiver is equipped with two DIGITAL IN terminals one

digital coaxial tetTninal and one digital optical terminal.

You can connect any component to one of the digital terminals using

a digital coaxial cable (not supplied) or digital optical cable (not

supplied).

Before plugging the receiver into an AC outlet, make sure that all

connections have been made.

Plug the power cord into an AC outlet.

IMPORTANT:

• When connecting the DVD player or+the DBS tuner" using the digital

terminal, you also need to connect it to the video jack on the rear.

Without connecting itto the video jack, you can view no playback

picture.

• After connecting the components using the DIGITAL IN terminals,

set the following correctly if necessary.

- Set the digital input (DIGITAL IN) terminal setting correctly. For

details, see "Digital Input (DIGITAL IN) Terminal Setting" on page

14.

- Select the digital input mode correctly. For details, see "Selecting

the Analog or Digital Input Mode" on page 14.

DBS tuner DVD player

Keep the power cord away from the

connecting cables and the antenna. The

power cord may cause noise or screen interference. We recommend

that you use a coaxial cable to connect the antenna, since it is well+

shielded against interference.

Note:

The preset settings such as preset channels and sound adjustment

may be erased in a few days in the following cases:

- When you unplug the power cord.

- When a power failure occurs.

CAUTIONS:

• Do not touch the power cord with wet hands.

• Do not pull on the power cord to unplug the cord. When unplugging

the cord, always grasp the plug so as not to damage the cord.

Before using the remote control, put two supplied batteries first.

When using the remote control, aim the remote control directly at

the remote sensor on the receiver.

CD player MD recorder

DIGITAL 1 (DVD) terminal, using a

digital coaxial cable (not supplied).

When the component has a digital

optical output terminal, connect it to the

DIGITAL 2 (CD), using a digital optical

cable (not supplied).

Before connecting a digital _.

optical cable, unplug the L_'I

protective plug. [_ 4dP_

D_GffN

DIGITAL2{CD'

_DIGFTALN

Notes:

• When shipped from the factory, the DIGITAL IN terminals has been

set for use with the following components.

- DIGITAL ! (coaxial): For DVD player

- DIGITAL 2 (optical): For CD player

• When you want to operate the CD player or MD recorder using the

COMPU LINK remote control system, connect the target

component also as described in "Analog connections" (see page 5).

• When you want to operate the DVD player using the AV COMPU

LINK remote control system, connect the DVD player also as

described in "Analog connections" (see page 5).

1. On the back of the remote control, remove the

battery cover.

2, Insert batteries. Make sure to match the polarity:

(+) to (+) and (-) to (-).

3. Replace the cover.

ffthe range or effectiveness of the remote control decreases, replace

the batteries. Use two R6P(SUM-3)/AA(I 5F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

• Place batteries in the remote control so they match the polarity: (+)

to (+) and (-) to (-).

• Use the correct type of batteries. Batteries that look similar may

differ in voltage.

• Always replace both batteries at the same time.

• Do not expose batteries to heat or flame.

Basic Operations

The following operations are commonly used when you play any sound source.

i I ! litll i [.im i_ _.IIdl_ilJ tl_-I i [. [O]J |_ _. h I. I ._I |

On the front oaneh

'lb turn on the power, press POWER.

The STANDBY lamp goes ofl_ The name of the

current source (or station fi-equency) appears on

the display.

Current source name appears

Current volume level is shown here

'lb turn off the power (into standby mode), _*_=='_.......

press POWER again. _

The STANDBY lamp lights up. A small amount ]POWER]

of power is consumed in standby mode. 'lb turn

the power off completely, unplug the AC power

cord.

From the remote control:

To turn on the power, press AUDIO POWER. AUDIO

The STANDBY lamp goes ofl_ The name of the

current source (or station fi-equency) appears on

the display.

'lb turn off the power (into standby mode),

press AUDIO POWER again.

The STANDBY lamp lights up.

[,,."]'_F'_'_'!11_,j[q,'?:'J[,-"_ 1_ I']_

Press one of the source selecting buttons.

On the front panel:

Selected source name appears

,,iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii iiTiiiiiiiii iiiTi

CH- IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII IIIII I

nnpROLOG_TF._. F.F. _.T CNETOUCH_

I[_ _E a_lc _55555_ t_t_l

I E]_.....s E]_,-.E,=,:.,-_.E%_o=1_=&._SUEE,:'",,OW.sL_L_I

_,4E_ tJ','ECLgS _¢t_ln FL_LL P_LION

DVD Select the DVD player for viewing the stereo

digital video disc.

TV SOUND/DBS Select the TV sound (or the DBS tuner).

VCR Select the video component connected to the

VCR jacks.

CD * Select the CD player.

TAPE/MD * Select the cassette deck (or the MD recorder).

PHONO * Select the turntable.

FMIAM * Select an FM or AM broadcast.

• Each time you press the button, the band

alternates between FM and AM.

Notes:

• WhenconnectinganMDrecorder(totheTAPE/MDjac_s)oraDBS

tuner (to the TV SOUND/DBS jac_s), change the source name that

appears on the displa_ See page 11 for details.

• Whenyoupressoneofthesourceselectingbuttonsontheremote

control marked above with an asterisk (_), the receiver

automatically turns on.

Sianal and soeaker indicators on the disolay

• The signal indicators light up to indicate the incoming channel

signals.

......Only the indicators for the incoming signals light up. (When

analog input is selected, "L" and "R" always light up.)

• The fi-ame of the signal indicator (except for "LFE": See notes

below) lights up if the corresponding speaker is set to "LARGE"

or "SMALL" (for subwoofer, "YES").

TVSOO_S

CZ551

T_Et_ _ _H_NO FM_

CZ551gZSZl CZ551

From the remote control:

DVD TV SOUND/DBS VCR

Czl Cz1 CzI

CO TAPE/MD PHONO FMJAM

LFE

L: Light up when the left front channel signal comes in.

The frame of this signal indicator always lights up.

R: Light up when the right front channel signal comes in.

The frame of this signal indicator always lights up.

C: Light up when the center channel signal comes in.

LS: Light up when the left rear channel signal comes in.

RS: Light up when the right rear channel signal comes in.

S: Light up when the monaural rear channel signal comes in.

LFE: Light up when the LFE channel signal comes in.

Notes:

• WhentheLFE channelsignalcomesin, "LFE"lightsup.

• When "SUBWOOFER"issetto "YES,"(Seepage 15)

lights up.

Selectino different sources for Bicture and sound

You can watch picture from a video component while listening to

sound from another component. Press one of the audio source

selecting buttons (CD, TAPE/MD, PHONe, FM/AM, TV

SOUND*), while viewing the picture from a video component such

as the VCR or DVD player, etc.

On the front panel:

w so_Bs

From the remote control:

TV SOUND/DBS

CD TAPE/MD PHONO FM/AM

Notes:

• Onceyouhaveselectedavideosource, picturesofthese!ected

source are sent to the TV until you select another video source.

* Except when your TVis connected through the AV COMPU LINK

remote control system (see page 27).

On the front Daneh

'lb increase the volume, turn MASTER

VOLUME clockwise.

'lb decrease the volume, turn it

counterclockwise.

• When you turn MASTER VOLUME rapidly,

the volume level also changes rapidly.

• When you turn MASTER VOLUME slowly,

the volume level also changes slowly.

From the remote control:

'lh increase the volume, press VOLUME +.

'lb decrease the volume, press VOLUME

CAUTION:

Always set the volume to the minimum before starting any source. If

the volume is set at its high level, the sudden blast of sound energy

can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of "O"(minimum) to

"80" (maximum).

On the front panel ONLY:

When you have connected two pairs of the front

speakers, you can select which to use. Pressing

SPEAKERS 1 or SPEAKERS 2 activates the

respective set of speakers.

• To use the speakers connected to the FRONT SPEAKERS @

terminals, press SPEAKERS 1 to set it in the -- ON position, and

press SPEAKERS 2 to set it in the • OFF position.

• To use the speakers connected to the FRONT SPEAKERS @

terminals, press SPEAKERS 2 to set it in the -- ON position, and

press SPEAKERS 1 to set it in the • OFF position.

• To use both sets of the speakers, press SPEAKERS 1 and

SPEAKERS 2 to set them in the ! ON position.

• To use neither set of the speakers, press SPEAKERS 1 and

SPEAKERS 2 to set them in the • OFF position.

Note:

When only one set of the speakers is connected to either the FRONT

SPEAKERS _1 or2 terminals, do not activate both pairs of the

speakers. If you do, no sound comes out of the front speakers.

Listenina only with headBhones

1. Connect a pail- of headphones to the PHONES jack on the fi-ont

panel.

2. Press SPEAKERS 1 and SPEAKERS 2 to set them in the •

OFF position.

CAUTION:

Be sure to turn down the volume before connecting or putting on the

headphones, as high volume can damage both the headphones and

your hearing.

Note:

You cannot shut off the sound through the other speakers using the

SPEAKERS ! and 2 buttons.

From the remote control ONLY:

Press MUTING to mute the sound through all MUTING

speakers and headphones connected. I[ _l ..-x

"MUTING" appears on the display and the

volume turns off(the volume level indicator goes

off).

To restore the sound, press MUTING again so that "OFF" appears

on the display.

• Taming MASTER VOLUME or pressing VOLUME also

restores the sound.

You can adjust the subwoofer output level if you have selected

"YES" for the "SUBWOOFER" (see page 11).

Once it has been adjusted, the receiver memorizes the adjustment.

Befbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start fi-om step 1 again.

With this Bass Boost function, you can boost the bass level.

Befbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On the front panel ONLY:

On the front panel:

l, Press ADJUST repeatedly until ADJUST

"SUBWFR LEVEL" appears on _===_¢_

the display.

• Once you have pressed ADJUST, MULTI CURSOR A / V

can be also used for selecting "SUBWFR LEVEL."

• The display changes to show the current setting.

2. Press MULTI CURSOR <_/ _ to ...........

adjust the subwoofer output level [ IL I

From the remote control: SOUND

1. Press SOUND. ('_--_.

The 10 keys are activated for sound adjustments.

Press ADJUST repeatedly until ADJUST

"BASSBOOST" (with the current

setting) appears on the display.

• Once you have pressed ADJUST, MULTI CURSOR A / V

can be also used for selecting "BASSBOOSTY

. Press MULTI CURSOR <_ / E> to

switch this function "ON" or

"OFF."

• When this function is switched "ON," the

BASS BOOST indicator on the display

lights up.

Note:

TheBass Boost function affects the front speaker sounds only

2. Press SUBWOOFER-/+ to adjust - SUBWOOFER+

thesubwooferoutputlevel(-lOdB 0 0 '' ' " ' "

to +10 dg). _> Youcan adjust the trebleand bass sounds as you like,

When the input level of the playing source is too high, the sounds

will be distorted, if this happens, you need to attenuate the input

signal level to prevent the sound distortion.

On the front panel ONLY:

P d h ld INPUTAT'I: (ONE TOUCH

tess an 0 osE_oucHO_ER,_T_ONt

OPERRATION) so that the ATT indicator

lights up on the display.

• Each time you press and hold the button, the

Input Attenuator mode turns on ("INPUT AFT

ON") or off ("INPUT NORMAL").

Notes:

• This function is available only for the sources connected using the

analog terminals.

• Thisfunctiondoesnottakeeffectwhendigitalinputisselected.

Betbre you start, remember...

There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Press ADJUST repeatedly until

ADJUST

"BASS" or "TREBLE" appears on

the display.

• Once you have pressed ADJUST, MULTI CURSOR A / V

can be also used for selecting "BASS" or "TREBLE."

• Select "BASS" to adjust the bass sound level.

• Select "TREBLE" to adiust the treble sound level.

. Press MULTI CURSOL <3 / _ to

adjust the bass or treble sound

level within the range of-10 to

+10.

• Each time you press the button, the sound

_uL_lCU_OR

level changes by ± 2 steps.

l Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while

others will make operations easie_

You can record any source playing through the receiver to a cassette

deck (or an MD recorder) connected to the TAPE/MD jacks and the

VCR connected to the VCR jacks at the same time.

While recording, you can listen to the selected sound source at

whatever sound level you like, without affecting the sound levels of

the recording.

Note:

The output volume level, tone adjustment (see page 10), bass boost

(see page 10) and DSP modes (see page !8) cannot affect the

recording.

When you have connected the MD recorder to the TAPE/MD jacks

or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,

change the source name shown on the display when you select the

MD recorder or the DBS tuner as the source.

On the front panel ONLY:

When changing the source name from "TAPE" to "MD':

1. Press TAPE/MD. '......

• Make sure "TAPE" appears on the display.

%/"

2, Press and hold SOURCE NAME

(TAPE/MD) until "ASSGN. MD"

appears on the display-.

If the sounds you hear from the front right and left speakers are

unequal, you can adiust the speaker output balance.

Betbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start fi-om step 1 again.

On the front Banel ONLY:

1. Press ADJUST repeatedly until ADJUST

"L/R BALANCE" appears on the _====x-x'_W'x)

display.

%_/

• Once you have pressed ADJUS'I; MULTI CURSOR A / V can

be also used for selecting "L/R BALANCE."

'lb change the source name from "MD" to "TAPE," repeat

the same procedure above (in step 1, make sure "MD" appears

on the display).

When changing the source name from "TV SOUND" to "DBS':

1. Press TV SOUND/DBS.

• Make sure "TV SOUND" appears on the

display.

2. Press and hold SOURCE NAME

(TV SOUND/DBS) until "ASSGN.

DBS" appears on the display.

2. Press MULTI CURSOR <s / E> to ..........

adjust the balance. [I-_ I_ I_-]]

• Pressing <1decreases the right channel I "+1

output (from "L-2I to "1{-21 ) _:'-,ff._.N_-._

• Pressing t> decreases the left channel .';....-" _,...//

output (from "R-2 l" to "L-2 l').

k'_RN_I R,'_ b-am,'Ig/r/rll_11II;'I_

Betore you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start fi-om step 1 again.

'lb change the source name from "DBS" to "TV SOUND,"

repeat the same procedure above (in step 1, make sure "DBS"

appears on the display),

Note:

Without changing the source name, you can still use the connected

components. However, there may be some inconvenience.

- "TAPE" or "TV SOUND" will appear on the display when you select

the MD recorder or DBS tuner.

- You cannot select the digital input (see page 14) for the MD

recorder and the DBS tune_

- You cannot use the COMPU LINK remote control system (see page

26) to operate the MD recorder.

On the front Banel ONLY:

1. Press SETTING repeatedly until SETTING

"SUBWOOFER" appears on the _=====_'N>

display.

%/"

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "SUBWOOFER."

• The display changes to show the current setting.

multi cu_om

PressMULTICURSORto IIjI

YES: Select this when a subwoofer is used.

NO: Select this when no subwoofer is used.

_1_ obtain the best possible sun-ound sound of the DSP (Digital

Signal Processor) modes (see page 18), you have to register the

information about the speakers arrangement after all connections are

completed.

Befbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start fi-om step 1 again.

Front, Center, and Rear Speaker Setting

On the front panel ONLY:

1, Press SETTING repeatedly until

"FRONT SPK" (Front Speaker),

"CENTER SPK" (Center

Speaker), or "REAR SPK" (Rear

Speaker) appears on the display.

• Once youhave pressed SETTING, MULTI

CURSOR A / V canbe also used for

selecting the speakers.

SETTING

MULtiCW_

2. Press MULTI CURSOR <1/ E> to /[_I " " il

select the appropriate item about I<_ I_l c>

the speaker selected in the above _.'}."_";_x_

step. _,./ _,/

r LARGE'.._,. SMALL'.._. NONE q

LARGE: Select this when the speaker size is relatively large.

SMALL: Select this when the speaker size is relatively small

NONE: Select this when you have not connected a speakeE

(Not selectable for the fi-ont speakers)

3. Repeat steps 1 and 2 to select the appropriate

items lbr the other speakers.

Notes:

• Keep the following comment in mind as reference when adjusting.

- If the size of the cone speaker unit built in your speaker is greater

than 12 cm, select "LARGE," and if it is smaller than 12 cm,

select "SMALL."

• If you have selected "NO" for the subwoofer setting, you can only

select "LARGE" for the front speaker setting.

• Ifyouhaveselected"SMALL"forthefrontspeakersetting, you

cannnot select "LARGE" for the center and rear speaker settings.

• When you change your speakers, you need to register the

information about the speaker again.

Center Delay Time Setting

comparing that of the sound fi-om the front speakers.

If the distance fi-om your listening point to the center speaker is

equal to that to the front speakers, select 0 msec. As the distance to

the center speaker becomes shorter, increase the delay time.

• 1 msec increase (or decrease) in delay time corresponds to 30 cm

decrease (or increase) in distance.

• When shipped fi-om the tZactory, delay time is set to 0 msec.

On the front panel ONLY:

SETTING

1. Press SETTING repeatedly until _/.x

"CENTER DELAY" appears on

the display.

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "CENTER DELAY."

• The display changes to show the current setting.

. Press MULTI CURSOR <_ / E> to _ ...........

select the delay time of the center/L IIAII

speaker output. II L;YqLk

• Pressing t> increases the delay time from _-,_ ..'._x_" 2

0 msec ("C. DELAY: 0ms ) to 5 msec ("C. ": "_"

DELAY: 5ms').

• Pressing <1 decreases the delay time from

5 msec ("C. DELAY: 5ms') to 0 msec ("C.

DELAY: 0ms').

Rear Delay Time Setting

comparing that of the sound fi-om the front speakers.

If the distance fi-om your listening point to the rear speakers is equal

to that to the front speakers, select 0 msec. As the distance to the rear

speakers becomes shorter, increase the delay time.

• 1 msec increase (or decrease) in delay time corresponds to 30 cm

decrease (or increase) in distance.

• Rear delay time for Dolby Digital and DTS Digital Surround is to

be set to 5 msec.

• When shipped fi-om the tZJctory, delay time is set to 5 msec.

On the front oanel ONLY:

1. Press SETTING repeatedly until

SETTING

"REAR DELAY" appears on the

display.

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "REAR DELAY."

• The display changes to show the current setting.

Press MULTI CURSOR <_ / E> to r-_ ..........

selectt edelaytimeaft erear11<1 14

speaker output. [_...-.',_",_ [x%_

• Pressing t> increases the delay time from _'_.../._ _..

0 msec ("R. DELAY: 0ms') to 15 msec

("R. DELAY: 15ms').

• Pressing <1 decreases the delay time from

15 msec ("R. DELAY: 15ms") to 0 msec

("R. DELAY: 0ms').

Crossover Frequency Setting Low Frequency Effect Attenuator Setting

Small speaker cannot reproduce the bass sound very well. So, if you

have used a small speaker any for the front, center, or rear channels,

this receiver automatically reallocates the bass elements, originally

assigned to the channel for which you have connected the small

speaker, to another channel (for which you have connected the large

speaker).

If you have selected "LARGE" for all speakers (see page 12), this

function will not take effect. '1_ use this function properly, you need

to set this crossover frequency level according to the size of the

small speaker connected.

This function takes effect in the following cases:

- When playing a source using Dolby Pro Logic, Dolby Digital,

or DTS Digital Surround.

- When using the DAP modes.

On the front panel ONLY:

1. Press SETTING repeatedly until SETTING

"CROSSOVER FRQ" (Crossover _'x_" "_

Frequency) appears on the display.

<.M

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "CROSSOVER FRQ."

• The display changes to show the current setting.

ffthe bass sound is distorted while playing back a source using

Dolby Digital or DTS Digital Sun-ound, follow the procedure below.

• This function takes effect only when the subwoofer (LF'E) signals

come in. (with "SUBWOOF'ER" set to "Yes.")

On the front panel ONLY:

1. Press SETTING repeatedly until SETTING

"LFE ATT" (Low Frequency _===_" "_

Effect Attenuator) appears on the

display.

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "LFE ATTY

• The display changes to show the current setting.

Press MULTI CURSOR <_ / E>to _ "..........

select thelow frequency effect [[ IIAII

attenuatorlevel. I<l 1 'IL

• AS you press it, the display changes to _._<"")_

show the following: ':'.-/'_/

0dB _ 10dB

0riB: Normally select this.

2, Press MULTI CURSOR <a / E> to

select the crossover frequency level

according to the size of the small

speaker connected.

• As you press it, the display changes to show the following:

V-80.z.-.100.z--120.z

10dB: Select this when the bass sound is distorted.

__ DY_:2:cCm_22 tgh: dC)::miPf:::::2fi_'eentct_:_ween maximum

sound and minimum sound) of the reproduced sound. This is useful

when enjoying surround sound at night.

• This function takes effect only when playing back a source using

Dolby Digital.

• Use the following comments as reference when adjusting.

80Hz: Select this when the cone speaker unit built in the

speaker is about 12 cm.

100Hz: Select this when the cone speaker unit built in the

speaker is about 10 cm.

120Hz: Select this when the cone speaker unit built in the

speaker is about 8 cm.

On the front oanel ONLY:

1. Press SETTING repeatedly" until SETTING

"D. RANGE CAMP," (Dynamic _'_"_

Range Compression) appears on

L./

the display.

• Once you have pressed SETTING, MULTI CURSOR A / V

can be also used for selecting "D. RANGE COME"

• The display changes to show the current setting.

, Press MULTI CURSOR <1 / E>to

select the appropriate item about

the compression level.

• As you press it, the display changes to

show the following:

_L_URSOR

I_OFF _ MID _ MAX*--- I

OFF: Select this when you want to enjoy surround with its

full dynamic range. (No effect applied)

MID: Select this when you want to reduce the dynamic

range a little. (Factory setting)

MAX: Select this when you want to apply the compression

effect fully. (Useful at night)

When you use the digital input temainals, you have to register what

components are connected to which terminals (DIGITAL IN 1/2).

Belbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start fi-om step 1 again.

On the front panel ONLY:

1. Press SETTING repeatedly until

"DIGITAL IN" appears on the

display.

• Once you have pressed SETTING, MULTI

CURSOR A / V can be also used for

selecting "DIGYIAL IN?'

• The display changes to show the current setting.

SETTING

DIGITAL 2 terminal setting

DIGITAL 1terminal setting

i. Press MULTI CURSOR <a / _> to /_--,, .......... ,, ,_

select an appropriate setting. >

As you press it, the display changes to show IL

the following: _._f:"')_,_? "_

1 DVD2CD ._- 1 DVD2DBS _ IDVD2MD

ICD2DVD ._- ICD2DBS _._- ICD2MD

1 DBS2DVD._- 1 DBS2CD _ IDBS2MD

1 MD2DVD _ 1 MD2CD _ IMD2DBS

(back to the beginning)

Note:

When shipped from the factory, the DIGITAL IN terminals can be used

as the digital input for the following components.

• DIGITAL 1 (coaxial): For DVD player

• DIGITAL 2 (optical): For CD player

When you have connected some digital source components using the

digital terminals (see page 7), you need to change the input mode for

these components to the appropriate digital input mode correctly .............

AUTO/PCM, DOLBY DIGYIAL, or DTS.

Once the colrect mode is selected for each digital source

component, the mode is memorized until you change it.

1. Follow the steps in "Digital Input (DIGITAL IN)

Terminal Setting" to the left.

2. Press the source selecting button (CD, TAPE/MD,

TV SOUND/DBS, or DVD) lbr which you want to

change the input mode IYom analog input to

digital input.

Tv so_s

On the front panel

DVD TV SOUND/DBS

C51C51

CD TAPEIMD

C51C51

On the remote control

3. Press ANALOG/DIGITAL repeatedly until the

digital input mode you want appears on the

display.

A_LO_TAL

On the front panel

ANALOGtDIGffAL

On the remote control

Each time you press the button, the input mode changes as

follows:

--*ANALOG _ AUTO/PCM

(Digital) A

DTS _ DOLBY DIGITAL

(Digital) (Digital)

Normally select "AUTO/PCM," so the receiver automatically

detects the incoming digital signal. The DIGITAL AUTO

indicator lights up on the display. (The DIGITAL AUTO lamp

next to the ANALOG/DIGITAL button lights up.)

- When the receiver can recognize the digital signal coming

into the receiver, the frame of the digital signal indicator for

the detected signal lights up automatically.

- When the receiver cannot recognize the incoming signal

correctly, the frame of the digital signal indicator flashes.

If this happens, select the same digital input mode with the

incoming digital signal either "DOLBY DIGITAL" or

"DTS?'

Notes:

• Noise may come out of the speakers while searching or skipping a

multi-sound source encoded with Dolby Digital or DTS Digital

Surround. If this happens, select "DOLBY DIGITAL" or "DTS" for

digital input mode. (See above)

• When you change the source, the digital input mode will be

automatically reset to "AUTO/PCM."

JVC's One 'lBuch Operation function is used to assign and store

different sound settings for each different playing source. By using

this function, you do not have to change the settings every time you

change the source. The stored settings for the newly selected source

are automatically recalled,

The following can be stored for each source:

Volume level (see page 9)

Bass boost (see page 10)

]bne adiustment (see page 10)

Input attenuator mode (see page 10)

Subwoofer output level (see page 10)

Balance (see page 1l)

DSP modes

......3D-PHONIC mode settings (see page 21)

......DAP mode settings (see page 21)

......Surround mode settings (see page 22)

On the front oanel ONLY:

'lb store the sound settings

1. Press ONE TOUCH OPERATION ..................,_,_T,_

(INPUT ATT.) so that the ONE _,.<,.,

TOUCH OPERATION indicator

lights up on the display.

Using the Sleep Timer, you can t_all asleep to music and know the

receiver will turn off by itself rather than play all night.

From the remote control ONLY:

Press SLEEP repeatedly. SLEEP

The SLEEP indicator lights up on the display, [_ _

and the shut-off time changes as follows (in

minutes):

r 10 ..-_20 ..-,-30 ..-,-40 .._ 50 ..-_60 ..-,-70 ..-_80 ..-_90 q

O0 (Canceled) t n

When the shut-off time comes

The receiver turns off automatically.

"lb check or change the time remaining until the shut-off time

Press SLEEP once.

The remaining time until the shut-off'time appears in minutes,

• _1_change the shut-off time, press SLEEP repeatedly.

]b cancel the Sleep Timer

Press SLEEP repeatedly until "SLEEP 00min," appears on the

display. (The SLEEP indicator goes otiS)

• Turning off the power also cancels the Sleep Timer.

2. Adjust the sound using the functions listed above.

The newly adjusted settings are memorized,

'lb recall the sound settings

With the ONE TOUCH OPERATION lamp lit, the settings for the

currently selected source are recalled when the source is selected.

'lb cancel the One Touch Operation function

Press ONE TOUCH OPERATION (INPUT AT'E) so that the ONE

TOUCH OPERATION indicator goes off'.

(Even though the One Touch Operation function is canceled, the

recalled sound effects remain active.)

Note:

If the source is FM or AM, you can assign a different setting for each

band.

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.

i}j_j'j r_t._ Ls_Rrt_l l_j

On the front panel ONLY:

I. Press FM/AM to select the band. _....

The MULTI CURSOR A / V / <1 / t> _=======%_.<_

buttons can be now used for operating the

tuner.

• Each time you press the button, the band alternates between

FM and AM.

!... _ i..., .." h=. !'¢1 '_' .,,P

, i i ii i ,,

I I I ',,.' I :: ...........

lOP lk 1Qk VDI&ItE

2. Press MULTI CURSOR/x / v

repeatedly until "- TUNING +"

appears on the display.

- ru"" "''" ..i..

i,,i i i,,i i,.i

i i _1 i...i .

3. Press MULTI CURSOR <a / _>

until you find the frequency you

want.

• Pressing <1decreases the frequency.

• Pressing t> increases the fi-equency.

Notes:

• When you hold MULT! CURSOR <_/_> in step 3, the frequency

keeps changing until a station is tuned in.

• Whenastationofsufficientsignalstrengthistunedin, theTUNED

indicator lights up on the display

When an FM stereo program is received, the STEREO indicator

also lights up.

Once a station is assigned to a channel number, the station can be

quickly tuned. You can preset up to 30 FM and 15 AM stations.

To store the preset stations

Betbre you start, remember...

• There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step 1 again.

On the front panel ONLY:

1. Tune in the station you want to preset (see

"Tuning in Stations Manually").

If you want to store the FM reception mode for this station,

select the FM reception mode you want. See "Selecting the FM

Reception Mode" on page 17.

i i,,,i i i ,, k,, i,,,i i i

F ['[ 1--1 I :: ", i i i i "[ :Z:

lEO Ik lat_ "_LUUEL_ _

MEMORY

2. Press MEMORY.

IE3_ .._-,._ r,.= _":' _ "_"' '7

LINE_RFO_4 _+_=,,,,,,,_ i i "--" 11 I'IPI ....

,w Ik 1_- _JaE

"CH*' appears and the channel nt mber position stairs flashing

on the display for about 5 seconds.

Press MULTI CURSOR < / D to /_[_//

select a channel number while the I_ I_1 _ I

channel number position is IL2 qlCL

flashing. "_/_

I[_;N_ _,.., _...., _" _-_.,, ,

_ I P" Ill :'-: ." --'i Ill ["1 ":i"

_ _* _ " ®_i.' -

..............

I _ "_LUME

Note:

You can use the 10 keys on the remote control to select the preset

numbe_ When using the 10 keys, be sure that they are activated

for the tuner, not for the CD and others. (See page 29.)

Press MEMORY again while the MEMORY

selected channel number is _===_"5

flashing on the display.

The selected channel number stops flashing.

The station is assigned to the selected channel number.

5. Repeat steps 1 to 4 until you store all the stations you want.

To erase a stored preset station

Storing a new station on a used number erases the previously stored

one.

To tune in a preset station

On the front panel:

I. Press FM/AM to select the band.

• The MULTI CURSOR A / V / <1 / t>

buttons can be now used for operating the

tuner.

• Each time you press the button, the band

alternates between FM and AM.

.......

III _ ,,,i,

I" I'I .:: .. __ ..:..

lOO lk 1uk" YOURS

2. Press MULTI CURSOR/x / V _ ,

repeatedly until "- PRESET +"

appears on the display.

I I".l...=.Jl.... I

CX] [_ _ _ _

"1oo lk IO,_" You,re

3. Pr M LTI R R<O E>t ...........ess U CU SO / o_--

select a preset channel station. [ I[_]l II

. D-

• ) •

I ressmg<1decreasesthepresetchannel I<:a _l [:>L

number. _:¢:" _" N_

I ressmg t> increases the preset channel '-.....' _/"

number.

From the remote control:

I. Press FM/AM. FM/AM

• Each time you press the button, the band 11 _L_-<'-,

alternates between FM and AM.

....... _-l-I ....

,::.. .:_-

i'' i=i 1,,_?

I I I II I I I 1,1_,,

2. Press 10 keys to select a preset _¢_%_¢_ _7%

channel number.

• For channel number 5, press 5. @ @@_

• For channel number 15, press + 10 then 5. ...... ;';

•For channel number 20, press 10 then 10. @

• For channel number 30, press +10, +10, _70)/!ii_)- 1

then 10. _

Note:

When you use the 10 keys on the remote control be sure that they are

activated for the tuner, not for the CD and others. (See page 29.)

When an FM stereo broadcast is hard to

receive or noisy

You can change the FM reception mode while receiving an FM

broadcast.

On the front oanel ONLY:

If necessary, press FM/AM so that the /_

MULTI CURSOR A / V / <1 / _> buttons

can be now used tbr operating the tuner.

• Each time you press the button, the band

alternates between FM and AM.

, Press MULTI CURSOR/x / V

repeatedly until "FM MODE"

appears on the display.

I"" M I,,'I i"i I"_'. I_°

r" !'! !'! I_1L..'!-

Mut_ cu_so_

". ..-

u,35

Press MULTI CURSOR < / _> to ( -II II I/

switch the FM reception to l< F '- q m-H

"AUTO MUTING" or "MONO." L_.d[_

"t, .,,

AUT 0 H Eii ...../ v./

irm_m

l,,,h'=i I, I i"i

i'!! !i'.ii !

AUTO MUTING: When a program is broadcasted in stereo,

you will hear stereo sound; when in

monaural, you will hear monaural sounds.

This mode is also useful to suppress static

noise between stations. The AUTO

MUTING indicator lights up on the display.

MONO: Reception will be improved although you

will lose the stereo effect, in this mode, you

will hear noise while tuning into the

stations. The AUTO MUTING indicator

goes off on the display.

Page is loading ...

JVC DS-TP330 Owner's manual

Brand: JVC

Model: DS-TP330

Category: AV receivers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

JVC DS-TP330 Owner's manual

This manual is also suitable for

JVC DS-TP330 Owner's manual

Related papers

Other documents