Elite Screens ZSP-TR01-3.0 User manual

ZSP-TR01-3.0
Elite Screens
Brand
Elite Screens
Model
ZSP-TR01-3.0
Category
Flat panel accessories
Type
User manual

This manual is also suitable for

Elite Screens ZSP-TR01-3.0 is a wireless 5/12 Volt Projector Trigger designed for electric wall/ceiling projection screens. It has a control distance of up to 80 feet (25M) and supports trigger voltage from 3-15V. The device can be synchronized with the screen's drop/rise cycle via remote control. Once synchronized, the screen can be controlled with the projector's power cycle, allowing for automated screen operation.

Elite Screens ZSP-TR01-3.0 is a wireless 5/12 Volt Projector Trigger designed for electric wall/ceiling projection screens. It has a control distance of up to 80 feet (25M) and supports trigger voltage from 3-15V. The device can be synchronized with the screen's drop/rise cycle via remote control. Once synchronized, the screen can be controlled with the projector's power cycle, allowing for automated screen operation.

Rev. 11/13/2015 EA
www.elitescreens.com [email protected]
Wireless 5/12 Volt Projector Trigger for
Electric Wall/Ceiling Projection Screens (Roll Down/Up)
Part#ZSP-TR01-3.0
User Guide
SPECIFICATIONS
1. Size and Weight: W x H x D: 4.8”x2”x0.7”, Weight: 0.11LBS
2. Max. Control Distance: 80 feet (25M) Control Type: ASK / FSK
3. Projector Output Support Trigger Voltage: 3-15V
4. RF Spec. Frequency: 433Mhz, Power: Below 2milli-watts
5. Directions for user:
Watch our set up instructions video online at www.elitescreens.com/video/zsp-tr01-02-setup
Or Scan the QR Code:
a. Connect the wireless RF trigger controller and the projector as shown in Fig. 3.
b. Use the wireless RF trigger controller to synchronize the screen drop/rise with the projection’s
power cycle via remote control according to the version number on your screen.
Rev. 11/13/2015 EA
www.elitescreens.com [email protected]
ZSP-TR01 Synchronization Instructions
How to synchronize your 5-12V wireless trigger according to the version number?
Version 3.0
Step1: Make sure to unplug your screen from the power outlet
Step2: Hold the UP button on your 5-12V wireless trigger
Step3: While holding the UP button, plug the screen back to the power outlet
Step 4: Wait 5 seconds and then release the UP button
Step 5: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able
to control your screen with your projector’s power cycle.
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30
seconds for full off and on cycle each time)
Note: Once your RF remote has been activated, the synchronization will be saved even if the power is cut
off.
Fig. 3
Back of projector is shown for reference
only. 12-volt trigger output port will vary.
Rev. 11/13/2015 EA
www.elitescreens.com [email protected]
Troubleshooting steps for the Elite Screens ZSP-TR01
Wireless 5-12V Trigger Remote
Make sure the Wireless 5-12v trigger is properly synced to your Elite Electric
Screen before proceeding to the troubleshooting steps.
1. Before connection to the projector, press the Up and Down buttons on the
wireless 12V remote to confirm Up/Down screen control.
2. Check that the positive (+) and negative (-) wires match the pins in the 3.5mm
jack.
(Reversing the polarity will work in some cases)
3. Use a 9V battery to power the screen via the RJ-45 port with the provided
12-volt trigger (green=ground, red=positive), and check if it will operate the
screen Up/Down. If the 9V battery operates the screen, this indicates that the
projector is not sending a signal to the 5-12V wireless remote.
4. If these provided steps do not resolve the issue, then the wireless 12V trigger
remote must be replaced.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Elite Screens ZSP-TR01-3.0 User manual

ZSP-TR01-3.0
Elite Screens
Brand
Elite Screens
Model
ZSP-TR01-3.0
Category
Flat panel accessories
Type
User manual
This manual is also suitable for

Elite Screens ZSP-TR01-3.0 is a wireless 5/12 Volt Projector Trigger designed for electric wall/ceiling projection screens. It has a control distance of up to 80 feet (25M) and supports trigger voltage from 3-15V. The device can be synchronized with the screen's drop/rise cycle via remote control. Once synchronized, the screen can be controlled with the projector's power cycle, allowing for automated screen operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents