Elite Screens ZSP-TR01 User manual

Elite Screens
Brand
Elite Screens
Model
ZSP-TR01
Category
Data projectors
Type
User manual

Elite Screens ZSP-TR01 is a wireless RF projector trigger controller that allows you to synchronize your screen drop/rise with the projection’s power cycle via remote control. With a maximum control distance of 80 feet (25M), you can easily control your screen from anywhere in the room. The compact size and lightweight design make it easy to store and transport. The ZSP-TR01 supports trigger voltage from 3-15V, making it compatible with most projectors. The included user guide provides step-by-step instructions on how to synchronize your screen with the projector, making setup a breeze.

Elite Screens ZSP-TR01 is a wireless RF projector trigger controller that allows you to synchronize your screen drop/rise with the projection’s power cycle via remote control. With a maximum control distance of 80 feet (25M), you can easily control your screen from anywhere in the room. The compact size and lightweight design make it easy to store and transport. The ZSP-TR01 supports trigger voltage from 3-15V, making it compatible with most projectors. The included user guide provides step-by-step instructions on how to synchronize your screen with the projector, making setup a breeze.

Rev. 042710-JA
www.elitescreens.com [email protected]
Wireless RF Projector Trigger Controller
Part# ZSP-TR01
User Guide
Rev. 042710-JA
www.elitescreens.com [email protected]
SPECIFICATIONS
1. Size and Weight: W x H x D: 4.8”x2”x0.7”, Weight: 0.09LBS
2. Max. Control Distance: 80 feet (25M)
Control Type: ASK / FSK
3. Projector Output Support Trigger Voltage: 3－15V
4. RF Spec. Frequency: 315Mhz, Power：Below 2 milli-watts
5. Directions for user:
a. Connect the wireless RF trigger controller and the projector as shown below.
b. Use the wireless RF trigger controller to synchronize the screen drop/rise with the
projection’s power cycle via remote control according to the version number on
your screen. Version number can be located either on the screen’s end cap
sticker or on the outside sticker of the packaging box.
Location of version number
on end cap sticker.
Fig. 1
Location of version number
on packaging box sticker.
Fig. 2
Rev. 042710-JA
www.elitescreens.com [email protected]
Note: Directions for synchronizing your 5-12V wireless trigger according to the
version number.
Version 1.4 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Push the small button located on the circuit board on the left side of the projection screen
(please note: you may require a small sharp object to achieve this). After the LED light turns on,
press & hold the UP button on your Wireless RF Trigger Controller and make sure the LED light on
circuit board turns on.
Step 2: Continue to hold the up button for an additional 3-4 seconds. After 3-4seconds, your 5-12V
Wireless Trigger should be activated and you’ll be able to control your screen with your projector’s
power cycle.
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around
20-30 seconds for full off and on cycle each time)
Version 2.0 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Make sure to unplug your screen from the power outlet
Step 2: Hold the UP button on your 5-12V wireless trigger
Step 3: While holding the UP button, plug the screen back to the power outlet
Step 4: Wait 5 seconds and then release the UP button
Step 5: Your 5-12V wireless trigger should now be activated with your screen and ready to be used
and able to control your screen with your projector’s power cycle.
Repeat the steps again if not successful.
Note: Once your RF remote has been activated, the synchronization will be saved even if the power
is cut off.
Fig. 3
  • Page 1 1
  • Page 2 2
  • Page 3 3

Elite Screens ZSP-TR01 User manual

Elite Screens
Brand
Elite Screens
Model
ZSP-TR01
Category
Data projectors
Type
User manual

Elite Screens ZSP-TR01 is a wireless RF projector trigger controller that allows you to synchronize your screen drop/rise with the projection’s power cycle via remote control. With a maximum control distance of 80 feet (25M), you can easily control your screen from anywhere in the room. The compact size and lightweight design make it easy to store and transport. The ZSP-TR01 supports trigger voltage from 3-15V, making it compatible with most projectors. The included user guide provides step-by-step instructions on how to synchronize your screen with the projector, making setup a breeze.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents