Hayward Aqua Connect Quick start guide

Hayward
Brand
Hayward
Model
Aqua Connect
Type
Quick start guide

This manual is also suitable for

Step 1
The Aqua Connect Home Network is compatible with all Pro Logic and Aqua Plus
controls operating with software revision r4.20 or higher and Aqua Rite Pro con-
trols operating with software revision r1.20 or higher. To verify software revision,
refer to your installation manual. An AQL2-BASE-RF Base Station (sold sepa-
rately) must be installed on your Pro Logic, Aqua Rite Pro or Aqua Plus before
installing your Aqua Connect Home Network. For detailed installation instruc-
tions, refer to the AQL2-BASE-RF instruction manual.
Step 2
Settings
Menu
Teach Wireless:
+ to start
Press and hold
Wireless button
Teach Wireless:
Successful
Teach Wireless:
Successful
a. At the Pro Logic or Aqua Rite Pro, press the “Menu”
button (possibly multiple times) until “Settings
Menu” is displayed.
b. Press “<“ or “>” (again, possibly multiple times)
until “Teach Wireless” is displayed.
c. Press the “+” button. The pool controller should
now say "Press and hold Wireless button".
d. With the Aqua Connect Home Network close by
and powered up, depress the Teach button and con-
tinue to hold it down, until all 4 LEDs are on solid.
At this point you must release the Teach button.
e. The RF LED on the Aqua Connect Home Network
should be rapidly blinking. This indicates that Teach
Mode has been entered.
f. The pool controller should then report “Teach Wire-
less: Successful”. After this, the RF LED on the
Aqua Connect Home Network should always be
ON.
Step 3
Step 4
With the Aqua Connect Home Net-
work in the chosen location, plug in
the power cord. Plug the ethernet
cable into the Aqua Connect Home
Network and then into an open port
on the router. Wait for 30 seconds
and then look at the LEDs on the
front panel. What you should see is:
The RF LED should be on most or all of the time.
Step 5 Step 6
To control your Pro Logic, Aqua Rite Pro or Aqua
Plus remotely through the web, go to
www.aquaconnectweb.com where, after set-
ting up a new user account, you’ll be able to
enjoy a brief trial period. Call 1-800-HAYWARD
to subscribe for continuing web functionality. Be
sure to have your Aqua Connect Home
Network’s MAC address handy when you call.
Refer to Step 5 for the location of the Aqua Con-
nect Home Network’s MAC address. Once an
account has been setup, you should be able to
login and remotely monitor and control your pool
through an internet connection.
Find the last 3 characters of the Aqua
Connect Home Network’s MAC ad-
dress (on label beneath base) and
write them down. Now go to any PC
in your home network and open the
web browser. On your browser’s ad-
dress line, type “mypoolxyz” (where
x, y, and z are the last 3 characters
in the Aqua Connect Home
Network’s MAC address) and then press the Enter key (do not type “www” or
“.com”). The local server should start and your browser will display a page that
is similar to your pool controller. You should now be able to control your Pro
Logic, Aqua Rite Pro or Aqua Plus using this web page. If not, refer to the
manual for alternatives to this step.
Aqua Connect
Home Network
QUICK START GUIDE
Two LEDs or more must be lit for dependable operation. If this is not the case,
refer to your installation manual for more information.
Install AQL2-BASE-RF
(if not already present) Training the Device
Install
AQL2-BASE-RF
Base Station
Perform
Range
Test
Connect
to Home
Network
Setup Local
Control Setup Web
Control
Train Aqua
Connect Home
Network
Perform Range Test
Setup Local Control
Connect to Home Network Setup Web Control
6 easy
steps
AQL2-BASE-RF
Base Station
(sold separately)
Tighten nut
Main PCB
Connector for
Base Station
Press “Teach”
button
Press and hold the
“Teach” button. Continue to
hold the “Teach” button
WHILE plugging in the
power cord.
Keep pressing the
“Teach” button until
all four LEDs blink in
unison, then release
button.
Place the Aqua Connect Home Network
in a desirable location close to the home
network router.
5 ft
1
3
2
4
RF
Tx
Rx
Link
The Tx LED should be blinking.
The Rx LED should be on most of the time.
If the LEDs do not light up as described above, then disconnect and reconnect
the ethernet cable connection.
The LINK LED should be blinking on at least once a minute, usually 4
times per minute.
Bottom of Aqua
Connect Home Network
http://mypool319
092404A
  • Page 1 1

Hayward Aqua Connect Quick start guide

Hayward
Brand
Hayward
Model
Aqua Connect
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents