Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072 Installation guide

Lennox
Brand
Lennox
Model
Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072
Type
Installation guide

Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072

This replacement kit is designed for use with Lennox gas packaged units models KG/SG/ZG/LGH024-090. It includes a new combustion air inducer assembly, a gasket, and five #10 sheet metal screws. The kit is used to replace a faulty or damaged combustion air inducer, which is responsible for drawing air into the unit for combustion. Installing this kit can help to ensure that your unit is operating safely and efficiently.

Here are some of the features and benefits of the Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072:

Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072

This replacement kit is designed for use with Lennox gas packaged units models KG/SG/ZG/LGH024-090. It includes a new combustion air inducer assembly, a gasket, and five #10 sheet metal screws. The kit is used to replace a faulty or damaged combustion air inducer, which is responsible for drawing air into the unit for combustion. Installing this kit can help to ensure that your unit is operating safely and efficiently.

Here are some of the features and benefits of the Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072:

Page 1
INSTALLATION INSTRUCTIONS FOR COMBUSTION AIR INDUCER REPLACEMENT
KIT USED ON KG/SG/ZG/LGH024-090 GAS PACKAGED UNITS
Litho U.S.A.
506266-03
5/2016
Supersedes 506266-02
©2016
COMBUSTION AIR INDUCER
REPLACEMENT KIT
PACKAGED UNITS KITS
AND ACCESSORIES
Shipping and Packing List
Package 1 of 1 contains:
1- Combustion air inducer assembly
Bag assembly containing:
1-Gasket
5-#10 Sheet metal screws
Application
See table 1 for usage.
WARNING
Improper installation, adjustment, alteration, ser
vice or maintenance can cause property damage,
personal injury or loss of life. Installation and ser
vice must be performed by a qualified installer, ser
vice agency or the gas supplier
Installation
1- Disconnect all power and gas supply to unit.
2- Open the heat section access panel. See figure 1,
2, or 3.
CAUTION
As with any mechanical equipment, contact with
sharp sheet metal edges can result in personal in
jury. Take care while handling this equipment and
wear gloves and protective clothing.
FIGURE 1
COMPRESSOR
SECTION
MULLIONHEAT SECTION
TG/KG/LGH UNITS
FIGURE 2
OUTDOOR
SECTION
HEAT SECTION
SG UNITS
CONTROL
BOX
TABLE 1
Heating Input Speeds Kit
150, 105/108 Two-speed 44W30; 602107-02
65, 105/108, 150 Single-speed
- Units Built Through April 8, 2016. 19W04; LB-112090B
65, 105/108, 150
Single-speed
- Units Built April 11, 2016 Through July 8, 2016.
- P, Y, M, J-Volt Units Built After July 8, 2016.
13Y15*; LB-112090C
65, 105/108, 150 Single-speed
- G-Volt Units Built After July 8, 2016. 15F58; LB-112090D
*The 13Y15 kit can be used on units built before April 11, 2016 if a new flue tube (elbow) is ordered.
Page 2
FIGURE 3
HEAT SECTION
ZG UNITS
CONTROL
BOX
3- Disconnect jack/plug from harness routed to
combustion air inducer.
4- Remove screws securing combustion air inducer
to flue box. Remove combustion air inducer. See
figure 4.
5- Remove flue elbow from combustion air inducer and
set aside.
6- Fit flue elbow onto replacement combustion air
inducer.
7- Install replacement combustion air inducer and
gasket. See figure 5. Secure with screws provided
in kit.
8- Connect jack/plug to combustion air inducer.
9- Replace heat access panel and connect power
and gas. Start unit as shown in unit installation
instruction.
COMBUSTION AIR INDUCER
FIGURE 5
COMBUSTION
AIR INDUCER
GASKET
FLUE BOX
COMBUSTION AIR INDUCER
FLUE
BOX
COMBUSTION
AIR INDUCER
FIGURE 4
FLUE
ELBOW
  • Page 1 1
  • Page 2 2

Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072 Installation guide

Lennox
Brand
Lennox
Model
Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072
Type
Installation guide

Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072

This replacement kit is designed for use with Lennox gas packaged units models KG/SG/ZG/LGH024-090. It includes a new combustion air inducer assembly, a gasket, and five #10 sheet metal screws. The kit is used to replace a faulty or damaged combustion air inducer, which is responsible for drawing air into the unit for combustion. Installing this kit can help to ensure that your unit is operating safely and efficiently.

Here are some of the features and benefits of the Lennox Combustion Air Inducer Replacement Kit - LGH/SG/KG/ZG 024-072:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents