Lunos e2 mini Mounting instructions

Brand: Lunos

Model: e2 mini

Type: Mounting instructions

Mounting Instructions

Decentralized Ventilation System with Heat Recovery Type

e² mini

- Please pass on to User-

Contents Page:

About these instructions, Safety instructions, Technical data, Disposal 1

Dimension drawings, Mounting position 2

Scope of application, Shipping units 3

Assembly: Mounting tube, Outer grille 4

Assembly: Electrical installation and Electrical connection 5

Assembly: Heat exchanger unit and interior screen 6

Filter change, Cleaning, Additional and Spare parts 7

About these Instructions

 Read these instructions carefully and completely before executing assembly work! General safety

instructions and the safety symbols with respective notes in text form must be observed.

 These instructions are to be passed on to the user after completing assembly work (tenant, own-

er, building administration etc.).

Symbols in these instructions

This symbol warns of a risk of injury.

This symbol warns of a risk of injury from electricity

Safety Instructions

Caution! All terminals must be completely disconnected from the power supply before com-

mencing assembly work! The fan is insulated pursuant to Protection Class II, connection pro-

tection does not apply!

Attention! Electrical connections must be carried out by authorized qualified staff in accord-

ance with applicable VDE 0100!

Attention! This device must not be operated by children or persons (filter change/cleaning)

who are not able to operate it safely on account of their physical, sensory or mental capacity or

due to their inexperience or lack of skills. Children must be supervised to ensure they do not

play with the device.

Technical Data

Supply voltage: 230 VAC 50 Hz

Device voltage: 12 VDC SELV

Protection Class: IP 22

Flow rate: 5m³/h; 10m³/h; 20m³/h

Disposal

Dispose of packaging correctly sorted. If you wish to dispose of the device, observe applica-

ble conditions. Your local disposal center will provide relevant information.

Dimension drawing (all dimensions in mm)

Installation Position

Decentralized fans with heat recovery of the type e² mini only function in pairs in alternating operation.

One device operates for 50 s in supply air mode, the other for 50 s in exhaust air mode at the respec-

tive flow rate set. After this, the direction of air flow is changed. This ensures that the total flow rate

supplied is the same as the total air flow ejected. If a push-pull device pair is installed and operated in

two different rooms in the apartment, a sufficient volume of air must always be ensured between these

two rooms via adequately large dimensioned overflow air passages.

Minimum distance recommended when in-

stalling a device pair in one wall:

Minimum distance recommended when in-

stalling a device pair at a right angle:

□136 34 min. 167 14

15 133

Ø115

Assembly tube DI 100 mm,

DA 104 mm

Dimensions in mm

Do not position the device above sensitive furniture, surfaces or pictures, the wall beneath the device

should remain ‚unused‘.

Do not position the device above or near room thermostats.

Shipment units

Check the delivery with regard to completeness and perfect condition!

Assembly tube Outer grille

Insert e² mini Interior screen 2/IBM

Tube DI 100 mm

Plaster protective

Filter

Design screen

Cover

frame

Scope of application

Temperature range: - 15°C to + 40°C

Can be used at a relative humidity of up to 65% inside the apartment. Low condensate formation

may occur during the heating period. If limits are exceeded, switch off the device and close the interi-

or screen. Ensure supply of fresh air by opening the window.

Other outer grilles available on request!

Assembly—Assembly Tube and Outer Grille

Prepare wall cavities for the assem-

bly tube (via core bore hole, drill bit

Ø106 mm). If necessary, shorten the

tube to the required installation

length. Make sure there is a protru-

sion of the tube on both sides to

bridge the plaster thickness (after

plastering, the tube must be flush

with the plaster). Insert the tube and

seal it all round (Assembly adhesive

Order No. 038 733).

Apply the inside and outside plaster.

In the case of an outside closure to

be plastered, first replace the plaster

protective cover with the outside

closure.

Remove the outside plaster protec-

tive cover. Mount the outer grille

using the integrated claws (tighten

the screws). The solid plastic out-

side covers provided by Lunos en-

sure high resistance to driving rain

and can be used in the Stress

Group III pursuant to DIN 4108-3

(2012-04). Metal or metal-coated

covers can be used in Stress Group

I pursuant to DIN 4108-3 (2012-04).

In the case of buildings exposed to

wind or the risk of strong winds and

rain to the outside covers, further

measures of weather protection may

be required.

①

②

➂

inside

inside outside

outside

Plaster protective

Tighten the claws with screws

3 mm

Assembly – Electrical Installation and Electrical Connection

Caution! All assembly work on the fan must only be carried out when power has been disconnected from all

terminals!

Make sure all connection lines are de-energized before connecting the fan to the power supply !

(disconnection from power supply with at least 3 mm contact opening, e.g. all-pole circuit-breaker)

Each circuit connected to the ventilation system must be fitted with residual current protection (e.g. a RCD

switch)! Electrical connections must be carried out by qualified staff only!

Additional installations and electrical components in this ventilation system are not admissible!!

Triggering can be made via the

universal control 5/UNI and the

added feature control TAC. Re-

spective installation instructions

apply accordingly.

Select the position of the switch.

Slit the cable ducts (power cable +

cable to device pairs) and the

tubes (2 cm deep). Install the pow-

er cable (e.g. 3 x 1.5 mm² ) and

the cables to the device pairs (e.g.

3 x 0.75 mm² ). Prepare the cables

to the device pairs in the tube.

Circuit and switches are connected

in accordance with the wiring dia-

gram below.

➃

Power

Switch

Device 1

Out/In

Device 2

In/Out

horizontal

vertical

also slit tubes

for cables

only slit

tubes in

these four

sections

Joint box

Safety Instructions

Device cable pre-

pared in tube

I III II

Important! Set the

coding switches to

the functions re-

quired for e² mini

(refer to Installation

Instructions E 148).

Deviating coding

switch settings are

inadmissible and

result in malfunc-

tions!

Series switch 5/W2U

Front view

Universal

control

5/UNI

grey

red

black

W1 W2

+ 12V

rt bl li rt bl li

Device (e)1 Device (e)2

Out/In In/Out

Assembly – Heat exchanger unit and Interior screen

Remove the inside plaster protec-

tive cover and insert the heat ex-

changer unit into the assembly

tube, observe 15 mm distance.

Using the loop on the inside of the

heat exchanger unit, the unit can be

adjusted by pulling out, if required.

Connect the cable to the connector

and install into the tube in front of

the motor.

⑦

Cable Motor cable

red

blue

purple

⑧

Insert inside closure with filter, snap

the interior screen in in the Open

position!

Finished!

⑨

15 mm

„Open position“

„Closed position“

Catch lock

Fixing pin

Design screen

- Catch locks snapped in

- Fixing pins in front of

cover frame

- Design screen turned

180° compared to Open

position.

- Fixing pins sunk into the

bore holes of the cover

frame.

Filter change date planned filter change Filter type used

Please record the filter changes made below:

Filter Change

Cleaning

Wipe the interior screen and cover frame with a dry, soft cloth when required.

Filter change and cleaning must not be carried out by children and persons not able to execute

such work due to their physical, sensory or mental capacity, or due to their inexperience or lack of

skills.

Additional / Spare parts

The filter change display indicates

when a filter is dirty. In connection

with the universal control, a red

LED lights up continuously beneath

the switch.

Remove the design screen, re-

move the filter, install the new or

cleaned filter (cleaning of the filter

can be executed e.g. in the dish-

washer), put the design screen

back on.

The vents must not be obstructed

or covered.

Reset the filter change display by

rocking the rocker switch W1 once.

Functionality of the filter change

display in connection with the TAC

and LUNOS-KNX control is de-

scribed in the respective instruc-

tions.

I III II

LED lights up beneath switch

Design screen

Filter

Replacement filter Filter Class G3; pack of 3 Type 9/FB3R Order No.: 037 176

E 173/ 06.14

Deutschland

LUNOS Lüftungstechnik GmbH Tel.: 0 30 / 36 20 01 - 0

für Raumluftsysteme Fax: 0 30 / 36 20 01 - 89

Wilhelmstr. 31 email: [email protected]

13593 Berlin Internet: http://www.lunos.de

Notes

Lunos e2 mini Mounting instructions

Lunos e2 mini Mounting instructions

Lunos e2 mini Mounting instructions

Related papers

Other documents