Pluggit iconvent Operating instructions

www.pluggit.com

Operating and installation instructions

Pluggit iconVent

Decentralized residential ventilation with heat recovery

The technology makes the difference.

Innovations of Pluggit with an added value for the human being and environment.

The 2Q-ventilation typical for PLUGGIT room systems guarantees efficiency and

comfort for the distribution of supply air. The first Q - the displacement ventilation -

distributes the fresh air very slowly without any background noises and draughts in

the room. The second Q - the cross ventilation - causes a complete air flow of the

room. In this, the fresh air outlet in the outside wall area is positioned as far away as

possible from the door of the supply air room.

The special PLUGGIT iQoanda-air outlet is positioned above the access of the supply

air room, if possible. The Qoanda effect leads the air flow along the ceiling in the

furthest corner of the room. By means of this type of flow a comprehensive air quality

is ensured without any background noises and draughts.

The distribution systems of PLUGGIT allow an installation of pipe systems at all three

installation levels. For new buildings or renovation the ventilation ducts can be

assembled safely and easily: in the insulating layer of the floor, in the bare concrete

of the ceiling or below the ceiling.

The innovative and unique PLUGGIT ServoFlow-technology guarantees the supply of

utilization-oriented air volume for a building at any time. Above all, it ensures the

important balance of supply and exhaust air flows by means of an automatically

conducted calibration once a week and documents modifications, like the filter

contamination in the plant.

The energy efficiency of ventilation units is defined by two factors. The high heat

recovery of our ventilation units ensures low heat losses and comfortable supply air

temperatures. Decisive, however, is the power consumption. By means of highly

efficient direct current vans the operating costs are reduced to a minimum. Thus, the

ratio of heat recovery and power consumption, which means the efficiency, is the

most significant value and is defined as coefficient of performance. At the coefficients

of performance PLUGGIT ventilation units achieve maximum values of up to 26 and

thus guarantee an excellent energy efficiency.

CleanSafe stands for an easy cleaning. As a first company PLUGGIT had a cleaning

system certified which facilitates cost-effective cleaning and maintenance of all

system components, whether a round tube or a shallow duct distribution system is

installed.

Fresh air and heat supply in one system - faster, more flexible and more energy-

saving than common heating systems.

Perfect feel-good climate by means of optimal air humidity in the room air with the

air humidifier AeroFresh.

2Q

allfloor

ServoFlow

CleanSafe

1

BIA Single room ventilation unit iconVent Mono and iconVent Duo

1. General safety instructions ................................................................................................. 3

2. General notes ...................................................................................................................... 3

2.1. Appropriate use ................................................................................................................... 3

2.2. Non-appropriate use ........................................................................................................... 3

2.3. Warranty .............................................................................................................................. 3

3. Overview ............................................................................................................................. 4

3.1. Single-room ventilation unit iconVent Mono ...................................................................... 4

3.2. Single-room ventilation unit iconVent Duo ......................................................................... 5

4. Function/principle ............................................................................................................... 6

4.1. Single-room ventilation unit iconVent Duo ......................................................................... 6

4.2. Single-room ventilation unit iconVent Mono ...................................................................... 7

4.3. Cross ventilation .................................................................................................................. 8

4.4. Installation type single-room ventilation unit iconVent Duo .............................................. 9

4.5. Installation type single-room ventilation unit iconVent Mono and iconVent Duo ............ 10

4.6. Installation type single-room ventilation unit iconVent Duo and exhaust air van ........... 11

4.7. Installation type single-room ventilation unit iconVent Mono, iconVent Duo

and exhaust air van ........................................................................................................... 12

4.8. Regulation .......................................................................................................................... 13

4.8.1. Regulation schemes ................................................................................................ 14

4.9. Time-delay relay ................................................................................................................ 21

4.9.1. Connection diagram ................................................................................................ 21

4.9.2. Technical data .......................................................................................................... 21

4.9.3. Measurements ......................................................................................................... 21

5. Installation (qualified staff) ................................................................................................ 22

5.1. Notes for installation

......................................................................................................... 22

5.2. Assemble installation stone ICVS and installation sleeve ICVH

....................................... 23

5.2.1. Installation stone ICVS for single-room ventilation unit iconVent Mono ............... 23

5.2.2. Installation stone ICVS for single-room ventilation unit iconVent Duo .................. 23

5.2.3. Installation sleeve ICVH for single-room ventilation unit iconVent Mono ............. 24

5.2.4. Installation sleeve ICVH for single-room ventilation unit iconVent Duo ................ 24

5.3. Install single-room ventilation unit

.................................................................................. 25

5.4. Initial operation

................................................................................................................. 27

TABLE OF CONTENTS

2

BIA Single room ventilation unit iconVent Mono and iconVent Duo

5.5. Technical data .................................................................................................................... 28

5.5.1. Unit data ................................................................................................................... 28

5.5.2. Regulation ................................................................................................................ 28

5.5.3. Measurements ......................................................................................................... 28

5.5.4. Basic wiring diagram, electrical .............................................................................. 30

6. Operation (user) ................................................................................................................ 31

6.1. Overview regulation ........................................................................................................... 31

6.2. Increase/ reduce fan level ................................................................................................. 31

6.3. Reset filter alarm ............................................................................................................... 31

6.4. Error correction ................................................................................................................. 32

6.4.1. Disturbances ............................................................................................................ 32

7. Maintenance (user) ............................................................................................................ 33

7.1. Clean inside panel ............................................................................................................. 33

7.2. Clean ceramic heat exchanger .......................................................................................... 33

7.3. Clean/ change filter ........................................................................................................... 34

8. Decommissioning/disposal ................................................................................................ 35

8.1. Decommissioning at extension ......................................................................................... 35

8.2. Packaging ........................................................................................................................... 35

8.3. Old unit ............................................................................................................................... 35

3

BIA Single room ventilation unit iconVent Mono and iconVent Duo

2.1. APPROPRIATE USE

The decentralized single-room ventilation unit iconVent

Mono and iconVent Duo serve as regulated aeration and

ventilation of individual supply air rooms, for example, living

rooms and children's rooms as well as exhaust air rooms,

for example, kitchen and bathroom with window in accord-

ance with DIBt-approval.

2.2. NON-APPROPRIATE USE

Other uses of the decentralized single-room ventilation unit

than those described under "appropriate use" are inadmis-

sible.

The decentralized single-room ventilation unit shall not be

applied

for construction drying.

2.3. WARRANTY

For a full legal warranty claim the technical standards of

these operating and installation instructions shall be ob-

served.

1. GENERAL SAFETY INSTRUCTIONS

Warning:

The following safety instructions shall be noted, other-

wise injuries or damages can be implied:

z Before you begin with the installation and operation

of the decentralized single-room ventilation unit,

carefully read these operation and installation in-

structions.

z The installation and all electrical works shall only

be carried out by qualified staff.

z Consider all necessary legal and national standards

(accident prevention regulations and acknowl-

edged rules of technology) for the installation and

initial operation of t

he decentralized single-room

ventilation unit and observe them.

z Damages which occur due to product-inappropriate

storage, improper operation and installation or

non-appropriate use are excluded from each kind

of liability.

z Subject to technical changes.

2. GENERAL NOTES

4

BIA Single room ventilation unit iconVent Mono and iconVent Duo

3.1. SINGLE-ROOM VENTILATION UNIT

ICONVENT

MONO

1 Pluggit iconVent inside panel Mono ICVM-B

2 Base plate, inside

3 Plugg

it iconVent functional unit ICVF

4.1 Plugg

it iconVent installation stone ICVS

4.2 Plugg

it iconVent installation sleeve ICVH

5 Base plate, outsid

e

6 Ins

ulation mat

7 Plugg

it iconVent weather protection grid

Mono ICVM-WSG

3. OVERVIEW

unten

oben

unten

1

2

5

6

7

4.1

4.2

3

M+P-26A-1204

Note:

Depending on the construction plan the Pluggit iconVent

installation sleeve ICVH (4.2) can also be used instead of

the Pluggit iconVent installation stone ICVS (4.1).

This is designed as round EPP sleeve 198

mm.

5

BIA Single room ventilation unit iconVent Mono and iconVent Duo

3.2. SINGLE-ROOM VENTILATION UNIT

ICONVENT DUO

1 Pluggit iconVent inside panel Duo ICVD-B

2 Base plate, insid

e

3 Pluggit iconVent

functional unit ICVF

4.1 Pluggit

iconVent installation stone ICVS

4.2 Pluggit

iconVent installation sleeve ICVH

5 Base plate, outside

6 Ins

ulation mat

7 Pluggit iconVent

weather protection grid

Duo ICVD-WSG

unten

oben

unten

oben

unten

1

2

5

6

7

4.1

4.2

3

M+P-26A-1205

Note:

Depending on the construction plan the Pluggit iconVent

installation sleeve ICVH (4.2) can also be used instead of

the Pluggit iconVent installation stone ICVS (4.1).

This is designed as round EPP sleeve 198

mm.

6

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.1. SINGLE-ROOM VENTILATION UNIT ICONVENT DUO

Rotation direction A

1 Single-roo

m ventilation unit iconVent Duo

2 Functional

unit supply air operation

3 Supp

ly air

4 Functional

unit exhaust air operation

5 Exhaust air

Rotation direction B

1 Single-roo

m ventilation unit iconVent Duo

2 Function

al unit supply air operation

3 Supply air

4 Function

al unit exhaust air operation

5 Exhaust air

For the hygienically necessary exchange of air outside air is

fed into the fun

ctional unit (2) of the single-room ventilation

unit (1) and transported in the living room as supply air (3).

Humid and used exhaust air (5) is discharged through the

functional unit (4) out of

the building.

Approximately each 80 seconds the rotation direction of the

fans in the functional units (2) and

(4) is changed. This way,

also the direction of supply air (3) and exhaust air (5) is

changed.

The ceramic heat exchanger of the functional unit (4) is

heated by

the inside room temperature. This heat is sup-

plied at the change of rotation direction of the supply air (3).

Due to this operation a permanent heat recovery is

ac

hieved.

4. FUNCTION/PRINCIPLE

obenoben

unten

oben

unten

oben

unten

1

2

4

5

3

Outside wall

Inside wall

M+P-26A-1305

up

down

obenoben

unten

oben

unten

oben

unten

1

2

4

5

3

Outside wall

Inside wall

M+P-26A-1306

up

down

7

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.2. SINGLE-ROOM VENTILATION UNIT ICONVENT MONO

Rotation direction A

1 Single-room ventilation unit

iconVent Mono

2 Functional unit su

pply air operation

3 Supply air

Rotation direction B

1 Single-room ventilation unit

iconVent Mono

2 Functional unit exh

aust air operation

3 Exhaust air

The change of rotation direction of the fan in the single-

room ventilation unit icon

Vent Mono (1) is carried out corre-

spondingly as in the single-room ventilation unit

iconVent Duo.

The single-room ventilation units iconVent Mono (1) shall be

operated in

pairs for a regulation. This means one unit runs

in supply air operation whereas the second unit simultane-

ously runs in exhaust air operation. The change of rotation

dire

ction is also conducted simultaneously in pairs.

Only this way the balance between supply and exhaust air

volume stream required

according to DIN 1946-6 and

DIBt-approval can be guaranteed.

obenoben

unten

oben

unten

1 2

3

Outside wall

Inside wall

M+P-26A-1307

up

down

obenoben

unten

oben

unten

1 2

3

Outside wall

Inside wall

M+P-26A-1308

up

down

8

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.3. CROSS VENTILATION

Sample installation

1 Single-roo

m ventilation units

2 Regulation

3 Cross ventilation

4 Suppl

y air room, for example, living room and

dining room

5 Supp

ly air room, for example, bedroom

6 Suppl

y air room, for example, guest room

7 Suppl

y air room, for example, bathroom with window

8 Exhaust air room,

for example, kitchen with window

9 Overflow area, f

or example, corridor or hall

Thus the single-room ventilation units (1) can be controlled

b

y the regulation (2), so that a sufficient cross ventilation (3)

of the entire utilization unit is guaranteed.

For the realisation of cross ventilation (3)

the supply air

volume flows in this sample installation, for example, in the

living room and dining room (4), must be increased by +5 %.

In the opposite rooms, for example, in the bedroom (5) and

guest rooms (6), the exhaust air volume flows must by

higher by +5 %. Additionally suitable overflow openings, for

example, do

or undercuts are necessary.

In exhaust air rooms with windows, for example,

bathroom (7) and kitchen (8), no cross ventilation is neces-

sary. Here the single-room ventilation units (1) must be op-

erated in balance according to the DIBt-

approval. This

means they run independently with regard to air tech-

nology, independent from the settings of the supply air

rooms. In such a case either

two single-room ventilation

units iconVent Mono or one single-room ventilation unit

iconVent Duo must be installed.

In the overflow sector, for example, corridor or hall (9), an

own sin

gle-room ventilation unit can be renounced, be-

cause, as a rule, the cross ventilation

(3) is sufficient, in

order to achieve a sufficient air exchange in these rooms.

1

6

2

4 5

22

3

1 1

7

+5%+/-0% +/-0%

+5%

98

1

M+P-26A-1105

9

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.4. INSTALLATION TYPE SINGLE-ROOM

VENTILATION UNIT ICONVENT DUO

Sample installation

1 Single-room ventilation unit

iconVent Duo

2 Regulatio

n

3 Cross ventilation

4 Supply

air room, for example, living and dining room

5 Sup

ply air room, for example, bedroom

6 Supply

air room, for example, guest room or

children's room

7 Exhaust air

room, for example, bathroom with window

8 Exhaust air

room, for example, kitchen with window

9 Overflow are

a, for example, corridor or hall

Note:

The described installation type is valid for bathrooms

with integrated window.

1

6

2

4 5

22

3

1 1

7

+5%+/-0% +/-0%

+5%

98

1

M+P-26A-1105

10

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.5. INSTALLATION TYPE SINGLE-ROOM

VENTILATION UNIT ICONVENT MONO AND

ICONVENT DUO

Sample installation

1 Single-roo

m ventilation unit iconVent Mono

2 Single-roo

m ventilation unit iconVent Duo

3 Regulation

4 Supp

ly air room, for example, living and dining room

5 Supp

ly air room, for example, bedroom

6 Suppl

y air room, for example guest room or

children's room

7 Exhaust air room,

for example, bathroom with window

8 Exhaust air room,

for example, kitchen with window

9 Overflow area, f

or example, corridor or hall

Note:

The described installation type is valid for bathrooms

with integrated window.

1

6

4 5

3

2 2

7

+/-0%

98

1

M+P-26A-1106

11

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.6. INSTALLATION TYPE SINGLE-ROOM VENTILATION

UNIT ICONVENT DUO AND EXHAUST AIR VAN

Sample installation

1 Single-room ventilation unit

iconVent Duo

2 Exhaust

air fan according to DIN 18017-3

3 Regulatio

n

4 Supply

air room, for example, living and dining room

5 Sup

ply air room, for example, bedroom

6 Supply

air room, for example, guest room or

children's room

7 Exh

aust air room, for example, bathroom without window

8 Exhaust air

room, for example, kitchen with window

9 Overflow are

a, for example, corridor or hall

In flats with an inside bathroom without

window (7) an ex-

haust air fan (2) must be installed acc

ording to DIN 18017-3.

This has to generate an exhaust air volume flow

of 60 m³/h (V

AB

).

To realize a balanced air exchange additional volume flows

must

be generated in the supply air rooms, which balance

the air volume flow of the exhaust air fan. Only this way it

can be ensured that there is no vacuum in the utilization unit

and the single-room ventilation units (1) which are in ex-

haust air operation can continue to generate heat recovery.

Example:

The exhaust air fan (2) is connected with

two regulations (3)

of supply air rooms, as it is described here. The supply air

volume flow of the single-room ventilation units (1) must be

adjusted respectively +15 m³/h higher in the supply air op-

eration. By this, in total the 60 m³/h exhaust air volume flow

of

the exhaust air fan (2) is compensated.

The single-room ventilation unit (1) in the kitchen (8) con-

tinues to run in balance.

Note:

The described installation type is valid for inside bath-

rooms without window according to DIN 18017-3.

1

3

6

4 5

33

1

7 2

+/-0%

98

1

VAB = 60m /h

+15m /h

+15m /h+15m /h

+15m /h

3

33

3

M+P-26A-1107

12

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.7. INSTALLATION TYPE SINGLE-ROOM

VENTILATION UNIT ICONVENT MONO,

ICONVENT

DUO AND EXHAUST AIR VAN

Sample installation

1 Single-roo

m ventilation unit iconVent Mono

2 Single-roo

m ventilation unit iconVent Duo

3 Exhaust air fan according

to DIN 18017-3

4 Regulation

5 Supp

ly air room, for example, living and dining room

6 Supp

ly air room, for example, bedroom

7 Suppl

y air room, for example, guest room or

children's room

8 Exhaust

air room, for example, bathroom without window

9 Exhaust air room,

for example kitchen with window

10 Overflow area, f

or example, corridor or hall

The installation type with single

-room ventilation unit

iconVent Mono (1), iconVent Duo (2) and exhaust air fan (3)

is carried out correspondingly.

Example:

The exhaust air fan (3) is also connected with the

re

gulation (4), which also controls the single-room ventila-

tion units (1) for the cross ventilation. The supply air volume

f

low of the single-room ventilation units (1) must be adjusted

respectively +30 m³/h higher, as soon as and as long as the

e

xhaust air fan (3) is in operation.

Thus, in total the 60 m³/h (V

AB

) exhaust air volume flow of the

exhaust air fan (3) is compensates and hear recovery is guar-

anteed.

The single-room ventilation units iconVent Mono (1) and

i

conVent Duo (2) can be adjusted to various additional volume

flows depending on the number of installed units.

The single-room ventilation unit iconVent Duo (2) in the

ki

tchen (9) continues to run in balance.

Note:

The described installation type is valid for inside bath-

rooms without window according to DIN

18017-3.

1

4

7

5 6

2

8 3

V

AB

3

= 60m /h

+/-0%

109

1

3

+30m /h

3

+30m /h

M+P-26A-1108

13

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.8. REGULATION

1 Plug connector functional unit 1 (exhaust air)

2 Plug conn

ector functional unit 2 (supply air)

3 Plug conn

ector functional unit 3 (exhaust air)

4 Plug conn

ector functional unit 4 (supply air)

5 Plug conn

ector functional unit 5 (exhaust air)

6 Plug conn

ector functional unit 6 (supply air)

7 External entry, potential-

free 0/10 V

Plug the time-delay relay at the connection E1 (arrow).

8 Regulatio

n

The single-room ventilation units iconVent Mono and

iconVent

Duo as well as the exhaust air fan are controlled by

a regulation ICVC (8).

This has six plug connectors (1-6) for the connection of the

single-roo

m ventilation units as well as one plug

connector (7) for the connection of the exhaust air fan.

The connection of two single-room units iconVent Mono or

on

e iconVent Duo always shall be carried out at the horizon-

tally opposite plug connectors.

For the single-room ventilation units, which are always in-

stalled in pairs in the exhaust air rooms, for example,

kitchen,

bathroom and toilet with window, always both

upper plug connectors (1) and (2) shall be used.

As supply line for the supply voltage of the regulation (8) an

insulated cable 3 x 1.5 m

m² shall be applied.

Depending on the cable length the following insulated

c

ables are applied as control wire for the single-room

ventilation units:

• Cable length 0-12 m: 3 x 0.25 mm²

• Cable length 12-20 m: 3 x 0.6 mm²

• Cable length 20-25 m: 3 x 0.8 mm²

The regulation is carried out by the rotary switch (10).

Depending on the required air volume flow various oper-

ating modes can be adjusted, see from page 14 onwards.

2

7

4

6

E1 E2

1

3

5

3x1,5mm

2

8

M+P-26A-1210

Note:

Level C-F are without function assignment.

0

F

E

D

C

B

A

9

8

7

6

5

4

3

2

1

10

M+P-26A-1111

14

BIA Single room ventilation unit iconVent Mono and iconVent Duo

4.8.1. Regulation schemes

Legend

1 icon

Vent regulation

2 Additional volume

flow supply air

3 Additional volume

flow exhaust air

Example connection level 2

1 Conne

ction insulated cable

• Cable length 0-12 m: 3 x 0.25 mm²

• Cable length 12-20 m: 3 x 0.6 mm²

• Cable length 20-25 m: 3 x 0.8 mm²

Analogous to the below described example of level 2 the

conne

ction of all levels is carried out.

531

642

+ 0

- 0

1

2

3

M+P-26A-1180

531

642

+ 0

- 0

+ 0

- 0

+10m³/h

- 0

+10m³/h

- 0

+ 0

- 0

+ 0

- 0

Example:

children’s room

3 x 1,5mm² /

230V /

50Hz

Example:

Living room +10m

3

/h

additional volume flow

Example:

bedroom

Example:

Dining room +10m

3

/h

additional volume flow

Example:

kitchen

L

PE

N

1

M+P-26A-1309

15

BIA Single room ventilation unit iconVent Mono and iconVent Duo

Level 0

Level 1

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 0 Balance Balance Balance Balance Balance Balance

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 0 Balance Balance Balance Balance Balance Balance

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 1 Balance Balance +5 % +/- 0 % +/- 0 % +5 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 1 Balance Balance +/- 0 % +5 % +5 % +/- 0 %

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 5%

- 0

+ 0

- 0

+ 0

- 0

+ 5%

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 5%

- 0

+ 5%

+ 0

- 0

16

BIA Single room ventilation unit iconVent Mono and iconVent Duo

Level 2

Level 3

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 2 Balance Balance +10 m³/h +/- 0 % +10 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 2 Balance Balance +/- 0 % +10 m³/h +/- 0 % +10 m³/h

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 3 Balance Balance +12.5 m³/h +/- 0 % +12.5 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 3 Balance Balance +/- 0 % +12.5 m³/h +/- 0 % +12.5 m³/h

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 12,5m³/h

- 0

+ 0

- 0

+ 12,5m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 12,5m³/h

- 0

+ 0

- 0

+ 12,5m³/h

- 0

17

BIA Single room ventilation unit iconVent Mono and iconVent Duo

Level 4

Level 5

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 4 Balance Balance +15 m³/h +/- 0 % +15 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 4 Balance Balance +/- 0 % +15 m³/h +/- 0 % +15 m³/h

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 15m³/h

- 0

+ 0

- 0

+ 15m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 15m³/h

- 0

+ 0

- 0

+ 15m³/h

- 0

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 5 Balance Balance +20 m³/h +/- 0 % +20 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 5 Balance Balance +/- 0 % +20 m³/h +/- 0 % +20 m³/h

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 20m³/h

- 0

+ 0

- 0

+ 20m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 20m³/h

- 0

+ 0

- 0

+ 20m³/h

- 0

18

BIA Single room ventilation unit iconVent Mono and iconVent Duo

Level 6

Level 7

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 6 Balance Balance +30 m³/h +/- 0 % +30 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 6 Balance Balance +/- 0 % +30 m³/h +/- 0 % +30 m³/h

A

B

531

642

531

642

+ 0

- 0

+ 0

- 0

+ 30m³/h

- 0

+ 0

- 0

+ 30m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 0

- 0

+ 30m³/h

- 0

+ 0

- 0

+ 30m³/h

- 0

Rotation direction A Rotation direction A Rotation direction A

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Supply air Exhaust air Supply air Exhaust air Supply air Exhaust air

Level 7 +10 m³/h +/- 0 % +10 m³/h +/- 0 % +10 m³/h +/- 0 %

Rotation direction B Rotation direction B Rotation direction B

Plug

connector

Functional level

1

Functional level

2

Functional level

3

Functional level

4

Functional level

5

Functional level

6

Position Exhaust air Supply air Exhaust air Supply air Exhaust air Supply air

Level 7 +/- 0 % +10 m³/h +/- 0 % +10 m³/h +/- 0 % +10 m³/h

A

B

531

642

531

642

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

+ 0

- 0

+ 10m³/h

- 0

Page is loading ...

Pluggit iconvent Operating instructions

Pluggit iconvent Operating instructions

Other documents