2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. American Standard
  6. 256.1XX

American Standard 256.1XX User manual

  • Hello! I am an AI chatbot trained to assist you with the American Standard 256.1XX User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
Roughing-in Dimensions
10'
INSTALLATION
2
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
4
5b. AC Power Supply (for 2506.165/162 series)
5c. 10 ft. Extension Wire (for 2506.175/172 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 2506.155/153 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
114mm
(4-1/2)
500mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
32mm (1-1/4)
55.5mm
(2-3/16)
125mm
(4-7/8)
81mm
(3-3/16)
49mm
(2)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction single post mounting. Operates on
DC (battery) or AC permanent power. Water pressure range
from 20 to 125 psi. In-line strainer for solenoid is integral.
Single inlet 3/8 compression, built-in checks, and flexible
stainless steel 15" reach inlet hose for spout connection.
159mm
(6-1/4)
126mm
(5)
154mm
(6-1/16)
Fig. 1a
Fig. 1b
1
4
6
5
3
2
INSTALL SPOUT ASSEMBLY;
Fig. 1
CAUTION
Turn off hot and cold water
supplies before beginning
1
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT
SHANK (3) through center hole of mounting surface.
Fig. 1a.
2. Assemble "C" WASHER (4), STAR WASHER (5)
and LOCKNUT (6) onto threads of SPOUT SHANK (7)
from underside of mounting surface. Fig. 1b.
3. Align FAUCET and tighten LOCKNUT (6). Fig. 1b.
7
CODES AND STANDARDS:
These products meet or exceed the following coded
standards:
ANSI A117.1
ASME A112.18.1
CSA B 125
NSF 61/Section 9
ADA Compliant
MODEL NUMBER:
DC POWERED; single inlet
2506.155 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.153 with cast spout, 2.2 GPM vandal
resistant aerator.
AC POWERED; single inlet
2506.165 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.162 with cast spout, 2.2 GPM vandal
resistant aerator.
MULTI AC POWERED; single inlet
2506.175 single inlet operates up to 15 units in series
from one AC power supply, 0.5 GPM vandal
resistant aerator.
2506.172 single inlet operates up to 15 units in series
from one AC power supply, 2.2 GPM vandal
resistant aerator.
Fig. 4a
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968xxx
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
Installation Instructions
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968506
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
2506.1XX
OPTIONAL Mixing Valve
605XTMV Thermostatic mixing valve, flex hoses
3/8" compression 20" hose length.
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
Roughing-in Dimensions
10'
INSTALLATION
2
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
4
5b. AC Power Supply (for 2506.165/162 series)
5c. 10 ft. Extension Wire (for 2506.175/172 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 2506.155/153 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
114mm
(4-1/2)
500mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
32mm (1-1/4)
55.5mm
(2-3/16)
125mm
(4-7/8)
81mm
(3-3/16)
49mm
(2)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction single post mounting. Operates on
DC (battery) or AC permanent power. Water pressure range
from 20 to 125 psi. In-line strainer for solenoid is integral.
Single inlet 3/8 compression, built-in checks, and flexible
stainless steel 15" reach inlet hose for spout connection.
159mm
(6-1/4)
126mm
(5)
154mm
(6-1/16)
Fig. 1a
Fig. 1b
1
4
6
5
3
2
INSTALL SPOUT ASSEMBLY;
Fig. 1
CAUTION
Turn off hot and cold water
supplies before beginning
1
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT
SHANK (3) through center hole of mounting surface.
Fig. 1a.
2. Assemble "C" WASHER (4), STAR WASHER (5)
and LOCKNUT (6) onto threads of SPOUT SHANK (7)
from underside of mounting surface. Fig. 1b.
3. Align FAUCET and tighten LOCKNUT (6). Fig. 1b.
7
CODES AND STANDARDS:
These products meet or exceed the following coded
standards:
ANSI A117.1
ASME A112.18.1
CSA B 125
NSF 61/Section 9
ADA Compliant
MODEL NUMBER:
DC POWERED; single inlet
2506.155 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.153 with cast spout, 2.2 GPM vandal
resistant aerator.
AC POWERED; single inlet
2506.165 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.162 with cast spout, 2.2 GPM vandal
resistant aerator.
MULTI AC POWERED; single inlet
2506.175 single inlet operates up to 15 units in series
from one AC power supply, 0.5 GPM vandal
resistant aerator.
2506.172 single inlet operates up to 15 units in series
from one AC power supply, 2.2 GPM vandal
resistant aerator.
Fig. 4a
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968xxx
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
Installation Instructions
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968506
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
2506.1XX
OPTIONAL Mixing Valve
605XTMV Thermostatic mixing valve, flex hoses
3/8" compression 20" hose length.
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
Roughing-in Dimensions
10'
INSTALLATION
2
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
4
5b. AC Power Supply (for 2506.165/162 series)
5c. 10 ft. Extension Wire (for 2506.175/172 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 2506.155/153 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
114mm
(4-1/2)
500mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
32mm (1-1/4)
55.5mm
(2-3/16)
125mm
(4-7/8)
81mm
(3-3/16)
49mm
(2)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction single post mounting. Operates on
DC (battery) or AC permanent power. Water pressure range
from 20 to 125 psi. In-line strainer for solenoid is integral.
Single inlet 3/8 compression, built-in checks, and flexible
stainless steel 15" reach inlet hose for spout connection.
159mm
(6-1/4)
126mm
(5)
154mm
(6-1/16)
Fig. 1a
Fig. 1b
1
4
6
5
3
2
INSTALL SPOUT ASSEMBLY;
Fig. 1
CAUTION
Turn off hot and cold water
supplies before beginning
1
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT
SHANK (3) through center hole of mounting surface.
Fig. 1a.
2. Assemble "C" WASHER (4), STAR WASHER (5)
and LOCKNUT (6) onto threads of SPOUT SHANK (7)
from underside of mounting surface. Fig. 1b.
3. Align FAUCET and tighten LOCKNUT (6). Fig. 1b.
7
CODES AND STANDARDS:
These products meet or exceed the following coded
standards:
ANSI A117.1
ASME A112.18.1
CSA B 125
NSF 61/Section 9
ADA Compliant
MODEL NUMBER:
DC POWERED; single inlet
2506.155 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.153 with cast spout, 2.2 GPM vandal
resistant aerator.
AC POWERED; single inlet
2506.165 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.162 with cast spout, 2.2 GPM vandal
resistant aerator.
MULTI AC POWERED; single inlet
2506.175 single inlet operates up to 15 units in series
from one AC power supply, 0.5 GPM vandal
resistant aerator.
2506.172 single inlet operates up to 15 units in series
from one AC power supply, 2.2 GPM vandal
resistant aerator.
Fig. 4a
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968xxx
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
Installation Instructions
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968506
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
2506.1XX
OPTIONAL Mixing Valve
605XTMV Thermostatic mixing valve, flex hoses
3/8" compression 20" hose length.
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
1
1
8
3
2
7
4
Mixing ValveB a s e P r o d u c t
How to order the Selectronic Product
1. Choose Power Supply
2. Choose Desired Spout
• Single Hole Sink
• Single Inlet
• 1 and 3 Hole Sinks
• Hot and Cold Inlets
Base Product Mixing Valve (optional)
Installation Instructions
TOOLS REQUIRED; Fig. 2
Fig. 2
Fig. 1
1 Channel Locks
2 Adjustable Wrench
3 Plumbers' Putty or Caulking
4 Phillips Screwdriver
5 Flat Blade Screwdriver
6 Electric Drill & 1/4" Drill Bit
7 Tape Measure
1
2
3
4
5
6
7
Roughing-in Dimensions
10'
INSTALLATION
2
Fig. 2
1. Determine location of ENCLOSURE (1). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 2 in order for electrical
connections from the spout assembly to be made.
NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance
between wall supply and ENCLOSURE (1) must be
taken into consideration.
2. Remove 4 screws from COVER (2) and pull off
COVER (2). Hold the ENCLOSURE (1) in desired
location and mark the four mounting hole locations as
shown. Fig. 2.
3. The ENCLOSURE (1) works best if secured to a wall
stud or cross brace within the wall, using the SCREWS
(3) supplied. If the ENCLOSURE (1) is to be installed on
a tile or plaster wall the ANCHORS (4) and SCREWS
(3) should be used.
4. For installations on drywall or tiled walls; use
ANCHORS (4) and SCREWS (3) for securing
ENCLOSURE (1) to finished wall. Drill four 1/4" dia.
holes a minimum of 1-3/4" deep. Insert the four
ANCHORS (4) flush with face of the finished wall.
Align the ENCLOSURE (1) and Install the MOUNTING
SCREWS (3). Tighten to secure ENCLOSURE (1) to
mounting surface.
1524mm
(60)
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
2
4
3
1
1
1
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
3
NOTE: If using Mixing Valve (optional) See Sheet
#M968808 for installation instructions.
MOUNT ENCLOSURE; Fig. 2
2
1. Connect SUPPLY NUT (1) from spout assembly to
nipple on top of ENCLOSURE (2). Tighten with
adjustable wrench to make a water tight connection.
Fig. 3.
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
CONNECT SPOUT HOSE TO
ENCLOSURE; Fig. 3
CONNECT WATER SUPPLY TO
ENCLOSURE AND WALL SUPPLY;
Fig. 4
3
Fig. 3
4
1
2
1
3
3
Fig. 4
2
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on
ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to
FLEXIBLE SUPPLY HOSE (3). Tighten to make a
water tight connection. Use two wrenches to tighten if
necessary. Fig. 4.
3. Connect FLEXIBLE SUPPLY (3) directly to wall
supply. Connection on FLEXIBLE SUPPLY (3) is 3/8"
compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 4a.
Note: FLEXIBLE SUPPLY (3) measures 20" from the
bottom of the ENCLOSURE (1) base. If additional
supply length is required, installer must purchase parts
separately.
Important: If FLEXIBLE SUPPLY (3) is too long, loop to
avoid kinking.
COLD WATER OR
TEMPERED
WALL SUPPLY
4
5b. AC Power Supply (for 2506.165/162 series)
5c. 10 ft. Extension Wire (for 2506.175/172 series)
6. Circuit board
7. Mixing Valve ( optional must be ordered separately)
8. Key for vandal resistant aerator
1. Selectronic Spout Assembly
2. Mounting Kit
3. Electrical Enclosure
4. Supply Hose
5a. DC Power Supply (for 2506.155/153 series)
All American Standard Faucets Are Water Tested At Our Factory.
Some Residual Water May Remain In The Faucet During Shipping.
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To
ensure that your installation proceeds smoothly--please read these instructions carefully before you
begin.
UNPACKING
1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items
after they have been removed from the carton. Some items may be packaged partially assembled to other items.
5a
5b
6
5c
114mm
(4-1/2)
500mm
(20)
1524mm
(60)
381mm
(15)
3/8" COMP.
32mm (1-1/4)
55.5mm
(2-3/16)
125mm
(4-7/8)
81mm
(3-3/16)
49mm
(2)
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant
solid brass construction single post mounting. Operates on
DC (battery) or AC permanent power. Water pressure range
from 20 to 125 psi. In-line strainer for solenoid is integral.
Single inlet 3/8 compression, built-in checks, and flexible
stainless steel 15" reach inlet hose for spout connection.
159mm
(6-1/4)
126mm
(5)
154mm
(6-1/16)
Fig. 1a
Fig. 1b
1
4
6
5
3
2
INSTALL SPOUT ASSEMBLY;
Fig. 1
CAUTION
Turn off hot and cold water
supplies before beginning
1
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT
SHANK (3) through center hole of mounting surface.
Fig. 1a.
2. Assemble "C" WASHER (4), STAR WASHER (5)
and LOCKNUT (6) onto threads of SPOUT SHANK (7)
from underside of mounting surface. Fig. 1b.
3. Align FAUCET and tighten LOCKNUT (6). Fig. 1b.
7
CODES AND STANDARDS:
These products meet or exceed the following coded
standards:
ANSI A117.1
ASME A112.18.1
CSA B 125
NSF 61/Section 9
ADA Compliant
MODEL NUMBER:
DC POWERED; single inlet
2506.155 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.153 with cast spout, 2.2 GPM vandal
resistant aerator.
AC POWERED; single inlet
2506.165 with cast spout, 0.5 GPM vandal
resistant aerator.
2506.162 with cast spout, 2.2 GPM vandal
resistant aerator.
MULTI AC POWERED; single inlet
2506.175 single inlet operates up to 15 units in series
from one AC power supply, 0.5 GPM vandal
resistant aerator.
2506.172 single inlet operates up to 15 units in series
from one AC power supply, 2.2 GPM vandal
resistant aerator.
Fig. 4a
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968xxx
(In Toronto Area only: 1-905-3061093)
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.
customer's e-mail us at: faucetsupport@amstd.com
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
Installation Instructions
© 2007 American Standard
Certified to comply with ASME A112.18.1M
M968506
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
Moments Lavatory Faucet
with SELECTRONIC™ Technology
2506.1XX
OPTIONAL Mixing Valve
605XTMV Thermostatic mixing valve, flex hoses
3/8" compression 20" hose length.
'JHB
'JHC
3FNPWF&/$-0463&$07&3'JH
'FFEUIF8*3&$0//&$5034UISPVHIUIFUPQ
PG&/$-0463&'JHB
3FNPWF(30..&5GSPN&/$-0463'JH
'FFEUIFHSBZ4&/4038*3&UISPVHI
(30..&5GSPN$0//&$503'JHCE
*OTFSUHSBZ4&/4038*3&JOUP41-*51-6(
1VTI41-*51-6(JOUP(30..&5UPTFBM
'JHE
*OTFSU(30..&5CBDLJOUP&/$-0463&
'JHD
*OTUBMM#"55&3:POUP%$DJSDVJUCPBSE'JHF
/PUF'PS#"55&3:1"$,JOTUBMMBUJPOTFF*OTUBMM
#BUUFSZQBHF
*OTUBMM$*3$6*5#0"3%JOUP&/$-0463&
XJUI4&/4038*3&VOEFS#0"3%'JHD
*OTFSU4&/4038*3&$0//&$503JOUP
$*3$6*5#0"3%3&$&1503'JHF
$POOFDUXJSFTGSPN4&/403UP40-&/0*%7"-7&
3FEUP#MBDLUP'JHD
3FQMBDF&/$-0463&$07&35JHIUFODPWFS
TDSFXTGJSNMZ
%$7&34*0/#"55&3:'JH
#-"$,
3&%
&-&$53*$"-*/45"--"5*0/
'JHD
'JHE


'JHF
'JH

'JH
'JHC
3FNPWF&/$-0463&$07&3'JH
'FFEUIF8*3&$0//&$5034UISPVHIUIFUPQ
PG&/$-0463&'JHB
3FNPWF(30..&5GSPN&/$-0463'JH
'FFEUIFHSBZ4&/4038*3&UISPVHI
(30..&5GSPN$0//&$503'JHC*OTFSU
HSBZ4&/4038*3&JOUP41-*51-6(1VTI
41-*51-6(JOUP(30..&5UPTFBM'JHF
*OTFSU(30..&5CBDLJOUP&/$-0463&
'JHE
3FNPWF41-*51-6(GSPN108&34611-:
(30..&5*OTFSU108&3$03%$0//&$503
UISPVHI108&34611-:(30..&5*OTFSU
108&3$03%JOUP41-*51-6(1VTI
41-*51-6(JOUP108&34611-:(30..&5
UPTFBM'JHH
*OTFSU108&34611-:$0//&$503JOUP
3&$&1503POUIF$*3$6*5#0"3%'JHD
*OTUBMM$*3$6*5#0"3%JOUP&/$-0463&
XJUI4&/4038*3&VOEFS#0"3%'JHE
*OTFSU4&/4038*3&$0//&$503JOUP
$*3$6*5#0"3%3&$&1503TMPU'JHG
$POOFDUXJSFTGSPN4&/403UP40-&/0*%
7"-7&3FEUP#MBDLUP'JHE
3FQMBDF&/$-0463&$07&35JHIUFODPWFS
TDSFXTGJSNMZ
"$7&34*0/'JH
108&3
4611-:
$03%
3&%
'JHE
'JHF

'JHG
'JHD

$"65*0/
#FGPSFPQFOJOH&/$-0463&
EJTDPOOFDU"$QPXFSTVQQMZ





'JHH

#-"$,
'JHB
'03"$7&34*0/
.6-5*)00,61'JH
6OJU 6OJU 6OJU
4FF"$7FSTJPO&MFDUSJDBM)PPLVQGPSGJSTUVOJUPG
UIF.VMUJIPPLVQ
3FNPWF&/$-0463&$07&34GSPNBMM
&/$-0463&4
3FNPWF40-*%#-"$,*/4&35GSPNSJHIUTJEF
PG&/$-0463&BOESFQMBDFXJUIHSBZ1*&$&
(30..&53FQMBDFTPMJECMBDLJOTFSUTPO6OJU
XJUIHSBZ1*&$&(30..&5
5BLFUIFGU&95&/4*0/GSPN6OJUBOE
JOTUBMMJOUPSJHIUTJEFPG6OJUBOE-FGUTJEFPG6OJU
JOTFBMJOHXJSFJOUP41-*51-6(BTTIPXOJO'JHB
1VTI41-*51-6(JOUP(30..&5
*OTFSU$0//&$503GSPNGU&95&/4*0/
JOUP$*3$6*5#0"3%3&$&1503UPQPG6OJU
BTTIPXOJO'JH
*OTFSUPUIFSFOEPGGU&95&/4*0/JOUP-08&3
6(30..&5PG6OJUBQQSPYJNBUFMZGSPN
DPOOFDUPS'JH1VTI41-*51-6(JOUP
(30..&5UPTFBM
*OTFSUDPOOFDUPSPGGU&95&/4*0/JOUPMPXFS
SFDFQUPSBTTIPXOJOGJHPO$*3$6*5#0"3%PG
6OJU
'FFEHSBZTFOTPSXJSFGSPN6OJUUISPVHIVQQFS
6(30..&5PG6OJU&/$-0463&GSPN
DPOOFDUPS'JH*OTFSUXJSFJOUP41-*51-6(
1VTI41-*51-6(JOUP(30..&5UPTFBM'JHB
*OTFSU(30..&5CBDLJOUP&/$-0463&'JHC
3FJOTUBMM$JSDVJU#PBSEJOUP&ODMPTVSFXJUIBMM
XJSFTVOEFS#PBSE'JHC
$POOFDU6OJU3FEBOE#MBDL4FOTPSXJSFT5P
TPMFOPJEWBMWF3FEUP#MBDLUP'JHC
3FQFBU4UFQTUISPVHIGPSSFNBJOJOH6OJUTJO
.VMUJ)PPLVQ
'JH
'JHB
5801*&$&
(30..&5
5801*&$&
(30..&5

'FFEUIFHSBZGU&95&/4*0/UISPVHI306/%
(30..&54BOE6(30..&54BTJMMVTUSBUFEBCPWF
3&%
#-"$,
'JHC

."*/5&/"/$&
8IFOUIF4FOTPSEFUFDUTBVTFSUIFXBUFS
JNNFEJBUFMZTUBSUTUPGMPX8BUFSGMPXXJMMTUPQ5XP
TFDPOETBGUFSVTFSJTPVUPGTFOTPSSBOHF5IFPGG
EFMBZBMMPXTUIFVTFSUPDPNGPSUBCMZNPWFIJTIBOET
XJUIPVUUIFGMPXDZDMJOHPOUPPGG"TBQSFDBVUJPOB
TBGFUZUJNFSXJMMUVSOPGGUIFXBUFSBGUFSUIFTFOTPSIBT
CFFOCMPDLFEGPSTFDPOET5IFXBUFSXJMMTUBZPGG
VOUJMUIFCMPDLBHFJTSFNPWFEGSPNUIFEFUFDUJPO[POF
%FUFDUJPO;POFNNNN
%FGBVMU4FUBU'BDUPSZNN
)"/%8"4)4&/40301&3"5*0/
'JH
5PJOTUBMM/FX#"55&3:BMJHOBOEQSFTTEPXO
#"55&3:DPOUBDUTGBDJOHEPXOXBSEJOUPQPTJUJPO
VOUJMUBCTMPDLJOUPQMBDF
5PSFNPWFUIF#"55&3:TQSFBEUIFUXPUBCTPO
UIF)0-%&3XJUIZPVSUIVNCT5IF#"55&3:
XJMMSFMFBTF
3FNPWFUIF0-%#"55&3:
*OTUBMM/&8#"55&3:DPOUBDUTGBDJOH
EPXOXBSEJOUP)0-%&3BOEQSFTTEPXOJOUP
QPTJUJPOVOUJMUBCTMPDLJOUPQMBDF
'JH
)0850*/45"--"/%$)"/(&
#"55&3:'JH
#"55&3:)0-%&3
-0$,*/(5"#4
4FUUJOHUIF%FUFDUJPO;POF%JTUBODF
3FNPWFDPWFSGSPN&/$-0463&%JTDPOOFDU(3":
4&/4038*3&GSPNDJSDVJUCPBSEUIFOSFDPOOFDU
8IJMFUIF4&/403$0/530--&%JTCMJOLJOH
TMPXMZQMBDFZPVSIBOEJONNJOGSPOUPG
UIFTFOTPS'JHB
8IFOUIF-&%TUPQTCMJOLJOHBOETUBZT0/NPWF
ZPVSIBOEUPUIFEFTJSFEQPTJUJPOBOEIPMEJOQMBDF
VOUJMUIF-&%CFHJOTUPCMJOLBHBJO'JHB
0ODFUIF4&/403$0/530--&%CFHJOTUP
CMJOLBHBJOSFNPWFZPVSIBOEGSPNUIFEFUFDUJPO[POF
8IFOUIFGMBTIJOHTUPQTUIFEFUFDUJPOEJTUBODFJTTFU
)0850$)"/(&4&/403
3"/(&'BDUPSZTFUBU'JH
'JH
'JHB
'JH
%&5&$5*0/
;0/&
'JH
NNNN
#-*/,*/(-&%
'JHB
'JHB
#-*/,*/(-&%
6150
NN
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
M 968 5 0 6
MOMMENTS with
SELECTRONIC
LAVATORY FAUCETS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o duct nam e s li s ted here i n a r e tr a dem a rks o f A m e ric a n St a nda r d In c .
IN MEXICO 01-800-839-12-00
10
M 9 6 8 5 0 6
CHROME 002
Replace the "YYY" with
appropriate finish code
A923672-0070A
FAUCET SUPPLY
HOSE
M962411-0070A
MOUNTING KIT
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
M962388-0070A
SENSOR KIT
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
A950223-007L0A
SENSOR
DC POWERED; single inlet
2506.155
2506.153
AC POWERED; single inlet
2506.165
2506.162
MULTI AC POWERED; single inlet
2506.175
2506.172
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
M 9 6 8 5 0 6
MOMMENTS with
SELECTRONIC
LAVATORY FAUCETS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o duct nam e s li s ted here i n a r e tr a dem a rks o f A m e ric a n St a nda r d In c .
IN MEXICO 01-800-839-12-00
10
M 9 6 8 5 0 6
CHROME 002
Replace the "YYY" with
appropriate finish code
A923672-0070A
FAUCET SUPPLY
HOSE
M962411-0070A
MOUNTING KIT
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
M962388-0070A
SENSOR KIT
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
A950223-007L0A
SENSOR
DC POWERED; single inlet
2506.155
2506.153
AC POWERED; single inlet
2506.165
2506.162
MULTI AC POWERED; single inlet
2506.175
2506.172
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
M 9 6 8 5 0 6
MOMMENTS with
SELECTRONIC
LAVATORY FAUCETS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o duct nam e s li s ted here i n a r e tr a dem a rks o f A m e ric a n St a nda r d In c .
IN MEXICO 01-800-839-12-00
10
M 9 6 8 5 0 6
CHROME 002
Replace the "YYY" with
appropriate finish code
A923672-0070A
FAUCET SUPPLY
HOSE
M962411-0070A
MOUNTING KIT
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
M962388-0070A
SENSOR KIT
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
A950223-007L0A
SENSOR
DC POWERED; single inlet
2506.155
2506.153
AC POWERED; single inlet
2506.165
2506.162
MULTI AC POWERED; single inlet
2506.175
2506.172
FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
CAUTION
GENERAL CLEANING; Fig. 6
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
1
5
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
6
Fig.4
2
3
8
CAUTION
Before opening ENCLOSURE
disconnect AC power supply.
1
Fig.5
9
M 9 6 8 5 0 6
MOMMENTS with
SELECTRONIC
LAVATORY FAUCETS
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr o duct nam e s li s ted here i n a r e tr a dem a rks o f A m e ric a n St a nda r d In c .
IN MEXICO 01-800-839-12-00
10
M 9 6 8 5 0 6
CHROME 002
Replace the "YYY" with
appropriate finish code
A923672-0070A
FAUCET SUPPLY
HOSE
M962411-0070A
MOUNTING KIT
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
M962388-0070A
SENSOR KIT
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
PRODUCT NUMBERS
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
A950223-007L0A
SENSOR
DC POWERED; single inlet
2506.155
2506.153
AC POWERED; single inlet
2506.165
2506.162
MULTI AC POWERED; single inlet
2506.175
2506.172
/