FiberLamp FL5200 LED Fiber Optic Illuminator User guide

Brand
FiberLamp
Model
FL5200 LED Fiber Optic Illuminator
Type
User guide
FL5200 Quick Start Guide
Contents
• FL5200
• IEC 60320 C13 to NEMA 5-15 AC Power Cable
Connector and Switch Diagram
DMX Channels
Data (+)
Data (-)
Not Assigned
Internal Use Only
Internal Use Only
Not Assigned
DMX Ground
DMX Ground
3
2
5
-
-
4
1
1
1
2
3
4
5
6
7
8
5
4
3
2
1
female
5
4
3
2
1
male
Using the Pushbutton
Twinkle Wheel
Color
Mode 1 52 3 4
SettingSlow FastSlow-MedMediumMed-Fast
230117 A1
Fiber Installation Precautions
When using stranded fiber, make certain that no fibers come into
contact with the twinkle effect wheel. Contact over time can cause
accelerated failure of the twinkle effect wheel motor.
t 510.620.5155 [email protected]FiberLamp.com
IEC 60320 C14 Plug for AC Input
Power Switch
DIP-Switch for DMX Addressing
Pushbuttons for Manual Control (2)
RJ45 Connectors for DMX (2)
Female XLR5 Connector for DMX
Male XLR5 Connector for DMX
Mini-USB Service Port
(Manufacturer use)
Intensity Bar
INTENSITY +-
0-10V Dimming Pin-outs for RJ45 connector
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
1
2
3
4
5
6
7
8
NA
NA
10V Source
0-10V Sink
NA
NA
Reference
Reference
Blank N/A
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
5000K ( 1 CH )
Red
Green
Blue
Yellow
Cyan
Magenta
0
1
2
3
4
5
6
7
8
9
10
11
5000K ( Mixed )
4200K ( Mixed )
3000K ( Mixed )
Rainbow
Set DMX Address
DMX ADDRESS
The DMX address is set by binary dip switches.
U= UP D= Down
211
92
D
U
D
U
U
U
D
D
U
U
U
D
D
D
D
D
Example 1
Example 2
U
D
U
D
switched up
4 8
D
Value when
1 2 256128643216
DMX Pin-outs for
RJ45 connector
7
5000K
Red
Green
Blue
Magenta
Master Light Intensity
Twinkle Wheel
Strobe Control
8
1
2
3
4
5
6
Notes
Twinkle Wheel: 0-1 Wheel stopped, 2-125 clockwise rotation slow to fast,
126-131 Wheel stopped, 132-255 Counter clockwise rotation fast to slow.
Strobe Control: 0-1 No blinking, 2-255 Blink rate slow to fast.
•
•Current sink - Connect the variable feed of the controller to both pins 3
and 4. Connect the reference feed of the controller to pins 7 and 8.
Current source - Connect the variable feed of the controller to pin 4 only.
Connect the reference feed of the controller to pins 7 and 8.
To set the FL5200 in 0-10V dimming mode, set the DMX Address
DIP-switch pin #10 to the up position.
345678910
Dip-Switches
1 2
DMX Add
3 4 5 6 7 8 9 10
Dip-Switches
1 2
Color
DMX Control Channels
Connectors Function
Color Dimmable
Mode
XLR5RJ45Function
Typical Cat-5e Wire ColorRJ45Function
  • Page 1 1

FiberLamp FL5200 LED Fiber Optic Illuminator User guide

Brand
FiberLamp
Model
FL5200 LED Fiber Optic Illuminator
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents