Lutec 7120315213 Owner's manual

Brand
Lutec
Model
7120315213
Category
Motorcycle Accessories
Type
Owner's manual

Lutec 7120315213 is a post lantern with a photocell that automatically turns on at dusk and off at dawn, making it a great choice for outdoor lighting. It features three fixtures, each of which can accommodate up to a 60-watt incandescent bulb or equivalent LED or CFL bulb. The lantern is easy to assemble and install, and it comes with all the necessary hardware, including expansion bolts for securing it to a concrete surface. With its stylish design and reliable performance, the Lutec 7120315213 post lantern is a great addition to any home's exterior.

Lutec 7120315213 is a post lantern with a photocell that automatically turns on at dusk and off at dawn, making it a great choice for outdoor lighting. It features three fixtures, each of which can accommodate up to a 60-watt incandescent bulb or equivalent LED or CFL bulb. The lantern is easy to assemble and install, and it comes with all the necessary hardware, including expansion bolts for securing it to a concrete surface. With its stylish design and reliable performance, the Lutec 7120315213 post lantern is a great addition to any home's exterior.

1
IMPORTANT,
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
POST LANTERN
Owners Manual
MODEL #7120315213
2
PACKAGE CONTENTS
PART
DESCRIPTION
QUANTITY
B
Cover
3
C
Fixture
3
D
Top Pole
1
E
Middle Pole
1
F
Bottom Pole
1
A
F
G
D
B
C
A 3
Cap
E
G
Base
1
3
HARDWARE CONTENTS (not shown actual size)
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by
removing fuse (or switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not
permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire
insulation, which could cause serious injury or death from electric shock.
CAUTION:
●All electrical connections must be in agreement with local codes, ordinances or the National
Electric Code (NEC). Contact your municipal building department to learn about your local codes,
permits and/or inspections.
●Risk of fire — most dwellings built before 1985 have supply wire rated for 140º F. Consult a
qualified electrician before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment
grounding. Never use a fixture in a two-wire system that is not grounded. If you are not sure your
lighting system has a grounding means, do not attempt to install this fixture. Contact a qualified,
licensed electrician for information with regards to proper grounding methods as required by the
local electrical code in your area.
●If a dimmer control switch is used with this fixture, obtain professional advice to determine the
correct type and electrical rating required.
AA
BB
CC
DD
EE
Expansion Bolt
Qty. 3
Hexagon Screw
Qty. 3
Positioning
Paper
Qty. 1
Wrench
Qty. 1
Wire Nut
Qty. 6
White Wire
Qty. 1
Black Wire
Qty. 1
FF
GG
Wrench x 1
Hardware Used
Hexagon Screw x 3
BB
DD
Secure the bottom pole (F) to the base (G) with the hexagon
screws (BB) by using the wrench (DD).
White Wire
Hardware Used
Wire Nut x 3
EE
FF
x 1
PREPARATION
Before beginning to assemble or install lighting fixture, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is missing or damaged, do
not attempt to assemble, install or operate the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses, Ladder, Wire Stripper, 1/2 in. Wrench, 1/2 in. Ring
Spanner, Electric Drill.
G
F
4
2. Connect white wire from each fixture (C) to the white wire (FF)
and the white sensor line by twisting a wire nut (EE) onto bare
ends of the wires. Connect the black wire from each fixture (C)
to the red sensor line by twisting a second wire nut (EE) onto
the bare ends of the wires. Connect the black wire (GG) to the
black sensor line by twisting a thrid wire nut (EE) onto the bare
ends of the wires. Install the pole cover.
3.
3
ASSEMBLY INSTRUCTIONS
1. Attach the three fixtures (C) to the top pole (D) by screwing
the nuts.
1
BB
C
D
Black Wire
GG
x 1
2
EE
GG FF
C
7. Install the cap (A) and the cover (B) onto the fixture (C).
7
4. Pass the wire through the middle pole (E), and then turn
the top pole (D) clockwise into the middle pole (E).
4
E
Insert bulbs (not included). Use 60-watt max. medium-base
E26 incandescent bulbs.
Note: CFLs and LEDs are recommended for this item.
6.
6
5. Rotate the middle pole (E) clockwise onto the bottom pole (F).
5
5
F
E
D
A
B
C
Remove the preassembled nuts and washers from the
expansion bolts (AA). Then put the expansion bolts (AA) into
the drill holes.
Hardware Used
Expansion Bolt x 3
AA
C
9.
9
AA
8. Use the positioning paper (CC) to drill three holes on the
ground.
Hardware Used
Positioning Paper x 1
CC
8
CC
6
11. With the help of another person, align the holes on base (G)
with the expansion bolts and carefully place the pole
assembly over the positioning paper. Secure assembly with
washers and nuts removed in step 9.
11
10. Connect bare ground wire from the base (G) to the ground
wire coming from the ground by twisting a wire nut (EE) onto
bare ends of the wires. Connect white wire from the base (G)
to the white wire coming from the ground by twisting a wire
nut (EE) onto bare ends of the wires. Connect the black wire
from the base (G) to the black wire coming from the ground
by twisting a wire nut (EE) onto the bare ends of the wires.
Secure the wire nuts (EE) with electrical tape.
10
0
Hardware Used
Wire Nut
x 3
EE
EE
G
G
OPERATING INSTRUCTIONS
The light comes on during
the day.
The light flashes.
1. The fixture may be installed
in a relatively dark location.
2. There is dust on the
photocell.
1. Something is reflecting the
light.
1. Relocate the fixture.
2. Periodically clean the surface
of the photocell with a mild,
non-abrasive cleaner.
1. Relocate the fixture away from
reflective surfaces.
The photocell in the fixture is designed to detect light and
prevent the fixture from turning on when it senses daylight.
At dusk, the light will turn on throughout the night until dawn.
At dawn, the light will turn off throughout the day until dusk.
Note: If the fixture is installed in a shaded or covered area
where there is little direct sunlight, the light may come on
during the day.
Photocell
CARE AND MAINTENANCE
To clean, unplug lamp and wipe with a damp, non-abrasive cloth.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
The light will not go on.
1. No power.
2. Fixture may be wired
incorrectly.
3. Switch may be wired
incorrectly.
1. Make sure lamp fixture is
plugged in and power is on.
2. Check wiring.
3. Check wiring.
Fuse blows or circuit trips
when fixture is turned on.
Crossed wires or power
wire is grounding out.
Consult a certified electrician.
The fixture shakes in high
winds.
The screws and
nuts may
be secured incorrectly.
Make sure the screws and
nuts were secured tightly.
7
LUTEC USA LLC:
149B Houston Rd Troutman NC 28166
Ningbo UTEC Electric Co.,LTD
CN8, Far East Industry Park, Yuyao, China
www.lutec.com
support@lutec.com
Please call our Customer Service line at 877-714-8669
for assistance Monday - Friday 9 a.m. to 5 p.m. EST
Printed in China
.
3-YEAR LIMITED WARRANTY
If this product fails due to a defect in materials or workmanship within three (3) years from the date
of purchase, return it along with proof of date of purchase and it will be replaced with the same or
comparable model free of charge.
This warranty is void if damage or defect has resulted from accident, abuse, misuse or faulty repair.
This warranty gives you specific legal rights and you may have other rights that vary from state to
state.
IN NO EVENT WILL LIABILITY EXTEND TO ANY CONSEQUENTIAL, SPECIAL, INCIDENTAL
OR INDIRECT DAMAGES OF ANY KIND ARISING OUT OF THE USE OR MISUSE OF THIS
PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION
MAY NOT APPLY TO YOU.
8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Lutec 7120315213 Owner's manual

Brand
Lutec
Model
7120315213
Category
Motorcycle Accessories
Type
Owner's manual

Lutec 7120315213 is a post lantern with a photocell that automatically turns on at dusk and off at dawn, making it a great choice for outdoor lighting. It features three fixtures, each of which can accommodate up to a 60-watt incandescent bulb or equivalent LED or CFL bulb. The lantern is easy to assemble and install, and it comes with all the necessary hardware, including expansion bolts for securing it to a concrete surface. With its stylish design and reliable performance, the Lutec 7120315213 post lantern is a great addition to any home's exterior.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents