AETEK I36-200 Installation guide

Brand
AETEK
Model
I36-200
Category
Security camera accessories
Type
Installation guide
Gigabit High Power PoE Injector
Series
Quick Installation Guide
Non-PoE Switch
Data INP+D OUT
100~240V AC
I36-200 / I36-210 / I36-210-V2 / I39-200 / I39-210 / I39-210-V2
Model Description
I36-200 Indoor 60W PoH PoE output
I36-210 Indoor 60W IEEE 802.3 bt PoE output
I36-210-V2 Indoor 60W IEEE 802.3 bt PoE output
I39-200 Indoor 95W PoH PoE output
I39-210 Indoor 90W IEEE 802.3 bt PoE output
I39-210-V2 Indoor 90W IEEE 802.3 bt PoE output
I46-200 Outdoor 60W PoH PoE output
I46-210 Outdoor 60W IEEE 802.3 bt PoE output
I49-200 Outdoor 95W PoH PoE output
Model Description
I49-210-V2 Outdoor 90W IEEE 802.3 bt PoE output
I49-201 Outdoor 95W PoH PoE output
I49-211 Outdoor 90W IEEE 802.3 bt PoE output
I69-200 Industrial Gigabit 95W PoH PoE output
I69-210 Industrial Gigabit 90W bt PoE output
I69-210-V2 Industrial Gigabit 90W bt PoE output
I69-206 Industrial Gigabit 95W PoH PoE output
I69-216 Industrial Gigabit 90W bt PoE output
I69-216-V2 Industrial Gigabit 90W bt PoE output
CONNECTION
* 1x PoE injector * 1x AC power cord ( Indoor type only)
* 1x Quick Installation Guide
Power Green ON: power good; OFF: power failed.
PoE Amber ON: PD datected
PACKAGE CONTENTS
LED denitions
P/N: A625012503G
Installation Steps:
1. Connect the power cable to the injector. The Power LED (Yellow) should be lit.
2. Connect the Data IN port to a LAN switch using an Ethernet cable.
3. Connect the Power+Data OUT port to a powered device, i.e., IP camera, using another Ethernet cable. Make sure the
PoE LED is lit.
4. Check if the powered device (IP camera) is working properly. An IP camera may take up to 1 or 2 minutes to power up.
Input Power :
I69-200 / I69-210 / I69-210-V2 : 48~56VDC for 802.3 at / af 52~56VDC for 802.3 bt / PoH
I69-206 / I69-216 / I69-216-V2 : 12~56VDC
Input Power : 100~240VAC
Application
AC to DC
power Supply
Power+Data Out
Data In
Non-PoE Switch Power In
+
-
Ground screw
* Make sure the grouning
resistance is lower than
0.5Ω.
PoE LEDPWR LED
I69-200 / I69-210 / I69-210-V2 / I69-206 / I69-216 / I69-216-V2
AETEK INC.
6F, No.192-1, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82452822|W: www.aetektec.com|E: [email protected]
All specications are subject to change without noice.
Copyright © 2022 AETEK INC. All rights reserved.
100~240V Line IN
to camera from
network
for power
wires
for Ethernet
cables
Ground
Neutral
I46-200 / I46-210 / I49-200 / I49-210-V2 / I49-201 / I49-211
Route your power wires through a 3/4" conduit into the power box.
The wiring scheme is shown below. The power supply converts
100~240V power to the 95W PoE output to IP cameras.
If the power box is directly mounted to wall, drill holes
in a diameter of 9.5mm or 3/8", and 4cm deep.
(I49-201 / I49-211 Only)
Use the following mounting positions for the camera housings
(via BK-101 brackets). (I49-201 / I49-211 Only)
The power box can be mounted with the AT-100,AT-101
pole-mount, AT-200 corner-mount bracket, or directly
secured to a wall. (I49-201 / I49-211 Only)
BK-101
Application
Non-PoE Switch
Data INP+D OUT
100~240V AC
8mm
AC Power Cable
AC Power Cable Spec.
Wire Size 10~18AWG
Wire Strip Length 8mm
Use the included M8 hex socket screws to secure the power
box to a pole-mount or corner mount bracket.
3/4” conduit
M8
The mounting hole denition is illustrated below. The same
mounting hole pattern apply to all pole-mount and corner-mount
brackets.
Outdoor PoE Injector
  • Page 1 1
  • Page 2 2

AETEK I36-200 Installation guide

Brand
AETEK
Model
I36-200
Category
Security camera accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents