2. QUIO
  3. QU-RDT2-HF
QU-RDT2-HF

QUIO QU-RDT2-HF Installation guide

  • Hello! I've analyzed the Install Guide for the QUIO QU-RDT2-HF Touch Keypad LCD Display Reader. This document provides instructions on setting up and using the device, including its various features like touch panel, LCD display, communication options, security and status settings. I'm ready to answer your questions about the device.
  • What is the factory PIN?
    What are the communication options?
    What is the factory ID?
    How to set the port?
QU-RDT2-HF
Touch
Keypad
LCD
Display
Reader
Install
Guide
V0103
Quick-Ohm Küpper & Co. GmbH
Cronenfelderstraße 75 | 42349 Wuppertal
Tel: +49 (0) 202 404329 | Fax: +49 (0) 202 404350
E
-
Mail:
kontakt@quio
-
rfid.de
Web:
www.quio
-
rfid.de
QU
-
RDT2
-
HF
Specification
Spec
/
Item
QU
-
RDT2
-
HF
Transmit
Frequency
Read Range
Baud Rate
125KHz
/
13.56MHz
5~10cm / 2~6cm
19,200
bps
(4,800~230,400
bps)
EM or ISO14443A/B/ 15693 / Mifare
0.1Sec
Card
Compatibility
Card Read Time
Keypad
12
keys
LED Indicator
Communication
ID
3
LED
(RGB)
RS485
and
Wiegand
(26/32/34/42/66
Bits)
0001 ~ 9,999
LCD Display
Anti-Tamper Facility
Beep Tone
128x64
Dots
(16x4
Char)
LCD
with
backlight
Built-in(IR)
Built
-
in
Buzzer
Operating Temperature
-
10
˚
C~60
˚
C
Input
Voltage
8V~28V
DC
/
0.5
~
2W
Dimension (W
x
H x
D)
89.4
x
124
x
12
mm
◎
Installation Note:
This product uses the touch panel. when you installed and tightened the screws, please POWER
OFF over 5 seconds, and in this period,
PLEASE DO NOT put anything on the touch panel(e.g. Finger..etc) then reboot.
This procedure is for the panel calibration and recalculation the touch control funciton, to ensure it
can work correct and accurate.
QU
-
RDT2
-
HF
Instructions
Item
Setup
Logout
#
+
#
+
0
+
0
(Beep)
#
+
#
+
0
+
1
(Beep)
+
【
PIN
】
+
#
Login
Note:
Factory
PIN
：
1234
System
will
logout
automatically
after
30
sec
Please
Login
first
then
do
the
following
setting.
#
+
#
+
0
+
2
(Beep)
+
【
ID
】
+
#
ID
Setup
Note:
Factory
ID
：
1
#
+
#
+
0
+
3
(Beep)
+
【
YYYYMMDDhhnnss
】
+
#
Date
Time
Setting
Modify Login Pin
Backlight Delay
Port Setting
Note:
2011/01/29
03:25:23
→
20110129032523
#
+
#
+
0
+
4
(Beep)
+
【
New
PIN
】
+
#
(Beep) +【Time】+ #
Note:
Factory
PIN
：
1
2
3
4
#
+
#
+
0
+
5
Note:
0
(light
Steady
)
~
250sec
#
+
#
+
0
+
6
(Beep)
+
【
Interface
】
+
#
Note: 0：Wiegend、1：RS485、2：Wiegend & RS485 (Factory：2 )
+ # + 0 + 7 (Beep) +【Language】+ #
Note: 0：ENGLISH、1：繁體、2：簡體 (Factory：0 -ENGLISH )
+ # + 0 + 8 (Beep) +【Encode】+ #
Note: 0：UNICODE、1：BIG5、2：GB2312 (Factory：0- UNICODE)
+ # + 0 + 9 (Beep) +【Class】+ #
Note: 0：Disable、1：Enable, (Factory：0- Disable)
#
Language
Setting
Encode Setting
#
#
Status
Setting
Clear
：
'
✱
'
Change
Work
Status
：
Item
Setup
Item
Setup
Start Work # + 【1】
(Beep)
# + 【2】
(Beep)
Back for Duty
Start Overtime
# + 【4】
(Beep)
Finish Work
#
+
【
5
】
(Beep)
Finish Overtime
#
+
【
6
】
(Beep)
Leave on Duty # + 【3】
(Beep)
Please
enable
Status
Function
first.
/