PERRIN ROWE 9.250120 is an installation and user guide for a 3-hole widespread bathroom faucet. It includes instructions on how to install the faucet, including how to connect the flexible hoses, secure the spout, and adjust the pop-up waste. It also includes information on the faucet's temperature range (minimum 1°C/34°F and maximum 85°C/185°F) and recommended working pressure (minimum 1 bar/15 psi and maximum 5 bar/75 psi).
PERRIN ROWE 9.250120 is an installation and user guide for a 3-hole widespread bathroom faucet. It includes instructions on how to install the faucet, including how to connect the flexible hoses, secure the spout, and adjust the pop-up waste. It also includes information on the faucet's temperature range (minimum 1°C/34°F and maximum 85°C/185°F) and recommended working pressure (minimum 1 bar/15 psi and maximum 5 bar/75 psi).
3 HOLE WIDESPREADS
The Georgian Bathroom Collection
Installation & User Guide
Perrin & Rowe products are manufactured in the UK, using the latest
technology and built to the highest quality standards.
We would like to thank you for purchasing a Perrin & Rowe product and
take this opportunity to invite you to look at other luxury products by us.
Please contact us to receive our latest catalogue.
Perrin & Rowe is a registered trademark. 9003741U Issue 5
Temp Range:
Min 1°C/34°F
Max 85°C/185°F
Recommended
Working Pressure:
Min 1bar/15psi
Max 5bar/75psi
Ideal performance obtained with equal hot & cold pressures.
• U.3712LS-2
• U.3712LSP-2
* Where indicated please specify color
SPARES
9.17793*
9.18380*
9.26705
9.18380*
9.28400
9.13195
LT
9.13196
RT
9.13196
RTC
9.21198*/HOT
9.21198*/COLD
9.51786*
9.01797*/HOT
9.01797*/COLD
Mixer Service Kit
9.53723
9.12752*
9.26760*
9.24194*
9.12752*
1/2" NPT
11" CENTERMAX
Ø
2 3/8"
Ø
1 1/4"
1 3/4" MAX
1/2" NPT
6" - 15" CENTERS
• U.3713X-2
HOT IN
COLD IN
9.26705
9.26400
Ø
1 1/8"
Ø
1 3/8"
HOLE
ROHL WARRANTY POLICY
All products supplied by ROHL carry warranties against manufacturing defects.
Perrin & Rowe products carry a Limited Lifetime Warranty.
ROHL LLC will provide free of charge, as its options, replacement part(s) or product (or a comparable alternative
product) to replace those which have proven defective in materials or workmanship.
For full ROHL LLC WARRANTY please contact ROHL or visit www.rohlhome.com
9.250120
9.19653*
9.250120
SPARE PARTS & SERVICE
3 Parker
Irvine
CA 92618
(714) 557-1933
www.rohlhome.com
9.30195
LT
9.30196
RT
9.15402
9.26709*
Congratulations on the purchase of your Perrin & Rowe Bathroom Product. Correctly installed and with sensible
care, this product will give you many years of trouble free service.
IMPORTANT INFORMATION
Before you proceed... We recommend you engage the services of a registered plumber to install
this product.
For ease of possible future servicing, we also recommend the fitting of conveniently placed
isolating valves.
In addition to the guide below it is essential that the written information overleaf is carefully read
and understood.
Preparation Check Box for Installer
Flush the plumbing system before
installing the bathroom product.
Once unpacked remove large & small base seals,
rosette, hood & lever, securing nut, clamp plate,
pop-up and top waste ready for installation.
1
Secure spout with supplied Box Spanner.
Ensure all connections are firmly tightened
3
Please Note: Ceramic disc valves are fitted
as standard to this mixer. Flow from FULLY
OFF to FULLY ON is achieved by rotating the
handles a quarter turn.
2
CARE & MAINTENANCE
Wipe down after use to avoid water spotting and mineral build up.
Occasional cleaning with warm soapy water, followed by a polish with a soft cloth is all that is required to keep the
plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean theshower. Do not use any products
with ammonia bleach or limescale remover. You will damage the plated finish and void your guarantee.
BEFORE USE
• Carefully check the installation for leaks.
• If further building work is to be carried out in the vicinity, cover the tap with a plastic bag to avoid damaging
the finish.
• Please ensure that the installation complies with local plumbing codes.
4
WORK SURFACE
Base Ring
Large Base
Seal
Spout
Clamp Plate
Clamp Bolt
Securing Nuts
Box Spanner
WORK SURFACE
Rosette
Small Base
Seal
Washer
Backnut
Valve Body
Flexible Hose
Hood & Lever
WORK SURFACE
Hood & Lever
Rosette
Small Base
Seal
Washer
Backnut
Valve Body
Flexible Hose
Sidevalve to be installed from underside of work surface as
shown.
Ensure connection for flexible hose is facing towards spout.
Leave backnut at the bottom of valve body and place the valve
body up through the work surface hole.
Before screwing down the hood & lever please make sure
orientation of levers is correct. Slide the hood & lever over the
top of valve body just enough to see if it is correctly
orientated.
Correct orientation can be achieved by removing and turning
the vernier insert.
Screw backnut up to the underneath of the work surface.
Connect flexible hose as shown.
WORK SURFACE
BASIN/BIDET
Connect flexible hose as shown.
Connect HOT & COLDwater supplies to the side
valve inlets.
Ensure all connectionsare firmly tightened.
Adjusting Sink Waste
• Ensure that pop-up shaft is in position alongside pop-up
rod.
• Shaft and rod can be cut if space is restricted.
• Secure pop-up using clamp bracket.
• Adjust position of clamp bracket to achieve maximum
movement of pop-up shaft.
• Place pop-up into waste and adjust movement of
pop-up shaft.
O Ring
Pop-Up
Foam
Seal
Rubber Seal
Bottom
Waste
Pop-Up
Rod.
Clamp
Bracket
Pop-Up
Shaft
Top Waste
Vernier
Insert
Congratulations on the purchase of your Perrin & Rowe Bathroom Product. Correctly installed and with sensible
care, this product will give you many years of trouble free service.
The Georgian Bathroom Collection
Installation & User Guide
IMPORTANT INFORMATION
Before you proceed... We recommend you engage the services of a registered plumber to install
thisproduct.
For ease of possible future servicing, we also recommend the fitting of conveniently placed
isolating valves.
In addition to theguide below it is essential that the written information overleaf is carefully read
and understood.
Preparation Check Box for Installer
Flush the plumbing system before
installing the bathroom product.
Once unpacked remove large & small base seals,
rosette, hood & lever, securing nut, clamp plate,
pop-up and top waste ready for installation.
1
Secure spout with supplied Box Spanner.
Ensure all connectionsare firmly tightened
3
Please Note: Ceramic disc valves are fitted
as standard to this mixer. Flow from FULLY
OFF to FULLY ON is achieved by rotating the
handles a quarter turn.
2
CARE & MAINTENANCE
Wipe down after use to avoid water spotting and mineral build up.
Occasional cleaning with warm soapy water, followed by a polish with a soft cloth is all that is required to keep the
plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the shower. Do not use any products
with ammonia bleach or limescale remover. You will damage the plated finish and void your guarantee.
BEFORE USE
• Carefully check the installation for leaks.
•If further building work is to be carried out in the vicinity, cover the tap with a plastic bag to avoid damaging
the finish.
•Please ensure that the installation complies with local plumbing codes.
4
WORK SURFACE
Base Ring
Large Base
Seal
Spout
Clamp Plate
Clamp Bolt
Securing Nuts
Box Spanner
WORK SURFACE
Rosette
Small Base
Seal
Washer
Backnut
Valve Body
Flexible Hose
Hood & Lever
WORK SURFACE
Hood & Lever
Rosette
Small Base
Seal
Washer
Backnut
Valve Body
Flexible Hose
Sidevalve to be installed from underside of work surface as
shown.
Ensure connection for flexible hose is facing towards spout.
Leave backnut at the bottom of valve body and place the valve
body up through the work surface hole.
Before screwing down the hood & lever please make sure
orientation of levers is correct. Slide the hood & lever over the
top of valve body just enough to see ifit is correctly
orientated.
Correct orientation can be achieved by removing and turning
the vernier insert.
Screw backnut up to the underneath of the work surface.
Connect flexible hose as shown.
WORK SURFACE
BASIN/BIDET
Connect flexible hose as shown.
Connect HOT & COLD water supplies to the side
valve inlets.
Ensure all connections are firmly tightened.
Adjusting Sink Waste
• Ensure that pop-up shaft is in position alongside pop-up
rod.
• Shaft and rod can be cut if space is restricted.
• Secure pop-up using clamp bracket.
•Adjust position of clamp bracket to achieve maximum
movement of pop-up shaft.
• Place pop-up into waste and adjust movement of
pop-up shaft.
O Ring
Pop-Up
Foam
Seal
Rubber Seal
Bottom
Waste
Pop-Up
Rod.
Clamp
Bracket
Pop-Up
Shaft
Top Waste
Vernier
Insert
-
1
-
2
-
3
PERRIN ROWE 9.250120 is an installation and user guide for a 3-hole widespread bathroom faucet. It includes instructions on how to install the faucet, including how to connect the flexible hoses, secure the spout, and adjust the pop-up waste. It also includes information on the faucet's temperature range (minimum 1°C/34°F and maximum 85°C/185°F) and recommended working pressure (minimum 1 bar/15 psi and maximum 5 bar/75 psi).
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Rohl U.3706X-APC-2 Dimensions Guide
-
-
Perrin & Rowe 4799 Installation & User Manual
-
-
Lefroy Brooks JL 1222 Installation & Servicing Guide
-
Mira EXCEL Installation & User Guide
-
-
-
Bristan Quadrato Tap Range Installation Instructions & User Manual
-
Baxi Premier Plus 100 Water Heater User manual
