2. Computers & electronics
  3. Computer components
  4. Interface components
  5. Serial converters/repeaters/isolators
  6. Applied Motion Products
  7. SWM24-SF

Applied Motion Products SWM24-SF, SWM24-SF/QF Integrated Steppers User guide

  • Hello! I have analyzed the Quick Setup Guide for the Applied Motion Products SWM24 SF/QF stepper drive. The document details how to set up the drive, including power requirements, software configuration using the ST Configurator, and wiring instructions. It also outlines the connection types, operating modes and describes the self-test functionality to check the correctness of the wiring. Feel free to ask me any questions about the SWM24 SF/QF drive.
  • What is the input voltage range for the SWM24?
    What is the recommended fuse if using an external fuse?
    What software is used to configure the SWM24?
    Where can I download the ST Configurator software?
Requirements
▪A 12-70V DC power supply.
▪A personal computer running Microsoft Windows 98, 2000, ME, NT, XP, Vista or 7/8/10/11.
▪ST Congurator™ software (available at www.applied-motion.com/products/software).
▪A 3004-277-5M power cable, 3004-290-5M I/O cable, or a 3004-278-5M RS-232 programming cable as needed.
▪NOTE: Cables are NOT included and must be purchased separately.
▪For more detailed information, please download and read the SWM24 Hardware Manual, available at www.applied-
motion.com/support/manuals.
To begin, make sure you have the following equipment:
Step 2
(DO NOT apply power until all connections to the drive have been made.)
a) Download and install the ST Congurator™ software.
b) Launch the software by clicking: Start / Programs / Applied Motion Products / ST Congurator
c) Select the correct COM port using the drop down list
d) Connect the drive to your PC using the RS-232 programming cable
Step 1
Wire the drive to the DC power source.
(Do not apply power until Step 3)
Note - the SWM24 accepts DC voltages from 12-70V. If using
an external fuse, we recommend a 5 amp fast acting fuse.
(See the SWM24 Hardware Manual for more information about
power supply and fuse selection.)
Connect I/O, if required by your application. A 3004-290-5M
cable will be required.
(See the SWM24 Hardware Manual for more information about
wiring I/O to the SWM24.)
GND
EMI Filter
AC
Power
Input
LINE
LOAD
L
NN
L
V+
V-
P/N:092.00823.00 (LCR)
4
3
1
2
POWER
DC POWER
SUPPLY V-
V+
V+
V-
GND
920-0069 Rev D
SWM
SWM24-SF/QF Quick Setup Guide
PIN SIGNAL WIRE COLOR
1 DC + BRN
2 DC - WHT
3 DC + BLU
4 DC - BLK
METAL HOUSING FRAME GND & SHIELD SHIELD
CONNECTION CHART
Step 3
If you have any questions or comments, please call Applied Motion Products Customer Support:
(800) 525-1609, or visit us online at applied-motion.com.
18645 Madrone Pkwy, Morgan Hill, CA 95037
Tel: 800-525-1609 | applied-motion.com
a) Apply power to the drive. The drive model and rmware revision should be
automatically displayed. If they are not, check the com port setting.
b) Follow the conguration instructions in the ST Congurator™ help screens.
c) The ST Congurator™ software can be used to set up your drive to operate in several
dierent modes including: Pulse & Direction, Analog Velocity, and SCL.
d) ST Congurator™ includes a self test option (under the Drive menu) to verify
that the STM and power supply are correctly wired and congured.
920-0069 Rev D
SWM24-SF/QF Quick Setup Guide
/