3W SMD LED RECHARGEABLE HEAD TORCH
MODEL NO: HT105LED.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn or
damaged DO NOT use.
9 Ensure the torch is fully charged before initial use.
8 DO NOT charge in damp conditions.
8 DO NOT turn the torch on when it is being charged.
8 DO NOT shine directly into your, another person’s or an animal’s eyes.
8 DO NOT allow children to use the torch.
8 DO NOT handle or move the torch whilst it is being charged.
8 DO NOT use the torch if you suspect that the battery or the torch casing is damaged.
8 DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently
recharge the battery at least once every six months of non-use.
8 DO NOT attempt to open, disassemble, modify or service the battery pack.
8 DO NOT crush, puncture, short external contacts or dispose of in re or water.
9 Replace only with the battery pack designated for this product.
9 Recycle or dispose of used battery as stipulated by local regulation.
9 If the electrolyte in the cells gets on your skin, thoroughly rinse with water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Hands-free SMD LED spotlight with adjustable inclination to direct light as required. Features three settings - full light, low light or ashing.
Adjustable headband and foam brow for added comfort. Supplied with micro USB charging lead.
3. SPECIFICATION
Model No ......................................................... HT105LED.V3
Battery: .............................................. 3.7V 1.5Ah Lithium-ion
Charging Time: ..................................................................4hr
LED Type: ................................................................3W SMD
Lumen Output: ............................................................. 220lm
Operating Time: ............................2.5hr @100%, 8hr @ 30%
4. OPERATION
4.1. CHARGING (g.2)
4.1.1. Remove USB socket cover on battery pack.
4.1.2. Connect the USB lead to the port on the rear of the battery pack and a USB power socket. Turn on the power supply.
4.1.3. The charging LED on the lamp will light RED to show that charging has commenced.
4.1.4. When the battery has fully charged the LED will turn GREEN.
4.1.5. Switch off power supply, remove charging lead and replace socket cover on battery pack.
4.2. OPERATION
4.2.1. Adjust the three straps to t your head size.
4.2.2. To turn on press the red button on the back of the torch unit, once for 100%, twice 30% three times flashing and once more to turn off.
4.2.3. To switch on rear red light, with front light on hold down red button for 2 seconds, the rear red light will light up. To switch off, switch
off front light, rear light will default to off.
Refer to
instructions
HT105LED.V3 Issue 3 (H,3) 12/05/22
Original Language Version
© Jack Sealey Limited
g.1 g.2
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
Original Language Version
© Jack Sealey Limited
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
HT105LED.V3 Issue 3 (H,3) 12/05/22
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sealey LED449 User manual
-
Sealey HT301R Operating instructions
-
-
Sealey LED307.V2 User manual
-
Sealey LED180 Operating instructions
-
-
Sealey LED360.V5 User manual
-
-
-
Sealey RS800 User manual