Aqua Creek F-422PLH-2 Operating instructions

Integrated

Headrest

9889 Garrymore Ln

Missoula, MT 59808

888-687-3552 | +1-406-549-0769

www.aquacreek.com

PART #: F-422PLH-2

MANDATORY

LEAVE THIS MANUAL WITH LIFT OWNER

Read and follow all instructions.

Lift safety can only be ensured if the lift is installed and

operated according to these instructions.

• NEVER permit children to play on or around the lift

• Do not allow children to use the lift without adult

supervision

• NEVER apply direct water pressure to the electronics

• NEVER use the lift with a dry pool

Check entire box and all packing materials for parts. Before beginning assembly, read the

instructionsandidentifypartsusingtheguresandpartslistedinthisdocument.

It is critical that all parts be carefully inspected prior to installation. If any damage occurred in

transit,AquaCreekProducts,LLCmustbenotiedwithinthreedaysofreceiptofunit.

Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s

warranty and may affect the safety of the user.

READ CAREFULLY

1

The INTEGRATED HEADREST ASSEMBLY attaches directly to the chair assembly, and is adjustable

for optimum comfort. The components of the INTEGRATED HEADREST ASSEMBLY are shown below,

along with the chair to show how it attaches. The wing-nuts allow for quick adjustment without

having to remove the assembly from the chair. The headrest pad is also removable for cleaning.

Look over the diagram below to familiarize yourself with the components before installing and

using the INTEGRATED HEADREST ASSEMBLY.

1"

HEADREST

ADJUST

BRACKET

HEADREST

SUPPORT

BRACKET

HEADREST

PAD

1/4-20 WING-

NUT (2)

ADJUST HOLES

(1" INCREMENTS)

1/4" X 1"

BUTTON-HEAD

CAP-SCREW (2)

The Integrated Headrest Assembly

2

HOOKS & LOOPS

(PRESS TOGETHER)

HEADREST PAD

ADJUST

BRACKET

PUT IN LOOPS

FIRST

FLAPS

CLOSED

TOP

LOOPS

Installing The Headrest Pad

The ADJUST BRACKET must be removed from the assembly to install or remove the HEADREST

PAD. When installing the pad thread the bracket through the middle loop rst and slide the

pad up to the top loops. Thread the bracket through the top loops (one at a time) to complete

the installation. To remove the pad, reverse this procedure.

3

Installing The Headrest Assembly

WING-NUTS

LOOPS

HEADREST HEIGHT MAY

BE ADJUSTED WITH THE

HEADREST INSTALLED.

ADJUST

BRACKET

HEADREST PAD LOOPS

OVER ADJUST BRACKET

(REMOVE TO CLEAN)

SLIDE HEADREST

SUPPORT BRACKET

INTO SLOTS.

SUPPORT BRACKET

PAD

FACING

FORWARD

SLOTS

REMOVE WING-NUTS

TO ADJUST HEADREST

PAD UP OR DOWN.

TIGHTEN WING-NUTS

AFTER ADJUSTING.

1] If the HEADREST PAD has not yet been

installed, install it rst. The pad height may

be adjusted now, or after the assembly has

been attached to the chair. Assemble fully

as shown in the diagram to the right.

2] Slide the SUPPORT BRACKET into the

slots on the top of the chair.

The INTEGRATED HEADREST ASSEMBLY is

now ready to adjust and use.

NOTE: The INTEGRATED HEADREST ASSEMBLY will work on all 2nd generation 18” wide Aqua Creek

Products’ chairs*. The 18” chair comes standard on all Aqua Creek Products’ ScoutTM, RangerTM, Pro

PoolTM and PatriotTM pool lifts.

*(The 2nd generation 18” wide chair has the slots for the INTEGRATED HEADREST, where the 1st

generation 18” wide chair does not).

4

Aqua Creek F-422PLH-2 Operating instructions

Related papers

Other documents