Dell OptiPlex 7470 All-In-One Owner's manual

Category
All-in-One workstations
Type
Owner's manual

This manual is also suitable for

Dell OptiPlex 7470 All-in-One
Service Manual
Regulatory Model: W19C
Regulatory Type: W19C001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its
subsidiaries. Other trademarks may be trademarks of their respective owners.
2020 - 03
Rev. A00
1 Working on your computer............................................................................................................ 6
Safety instructions.................................................................................................................................................................6
Turning off your computer — Windows 10....................................................................................................................... 6
Before working inside your computer................................................................................................................................. 7
After working inside your computer.................................................................................................................................... 7
2 Technology and components......................................................................................................... 8
DDR4....................................................................................................................................................................................... 8
USB features........................................................................................................................................................................ 10
HDMI......................................................................................................................................................................................12
3 Major components of your system ............................................................................................... 13
4 Removing and Installing components............................................................................................15
Recommended tools............................................................................................................................................................ 15
Screw size list....................................................................................................................................................................... 16
System board layout............................................................................................................................................................ 17
Rubber feet........................................................................................................................................................................... 18
Removing the rubber feet.............................................................................................................................................19
Installing the rubber feet............................................................................................................................................... 19
Cable cover - optional.........................................................................................................................................................20
Removing the cable cover............................................................................................................................................20
Installing the cable cover............................................................................................................................................... 21
Stand ....................................................................................................................................................................................22
Removing the stand...................................................................................................................................................... 22
Installing the stand.........................................................................................................................................................23
Back cover............................................................................................................................................................................24
Removing the back cover.............................................................................................................................................24
Installing the back cover............................................................................................................................................... 24
Hard drive.............................................................................................................................................................................25
Removing the hard drive assembly............................................................................................................................. 25
Installing the hard drive assembly................................................................................................................................26
Memory module................................................................................................................................................................... 27
Removing the memory module.................................................................................................................................... 27
Installing the memory module...................................................................................................................................... 28
System board shield............................................................................................................................................................ 29
Removing the system board shield............................................................................................................................. 29
Installing the system board shield................................................................................................................................30
Intel Optane...........................................................................................................................................................................31
Removing the Intel Optane card.................................................................................................................................. 31
Installing the Intel Optane card.................................................................................................................................... 32
Solid State Drive -SSD........................................................................................................................................................33
Removing the SSD card................................................................................................................................................33
Installing the SSD card..................................................................................................................................................34
Contents
Contents 3
Solid State Drive -2230...................................................................................................................................................... 35
Removing the 2230 SSD card..................................................................................................................................... 35
Installing the 2230 SSD card........................................................................................................................................36
WLAN card........................................................................................................................................................................... 37
Removing the WLAN card............................................................................................................................................37
Installing the WLAN card.............................................................................................................................................. 39
System fan............................................................................................................................................................................ 41
Removing the system fan..............................................................................................................................................41
Installing the system fan............................................................................................................................................... 42
Heat sink...............................................................................................................................................................................43
Removing the heat sink - dGPU.................................................................................................................................. 43
Installing the heat sink - dGPU.................................................................................................................................... 44
Removing the heat sink - UMA................................................................................................................................... 45
Installing the heat sink - UMA......................................................................................................................................45
Pop-Up Camera...................................................................................................................................................................46
Removing the pop-up camera..................................................................................................................................... 46
Installing the pop-up camera........................................................................................................................................48
Coin cell battery...................................................................................................................................................................50
Removing the coin cell battery.................................................................................................................................... 50
Installing the coin cell battery...................................................................................................................................... 50
Processor.............................................................................................................................................................................. 51
Removing the processor............................................................................................................................................... 51
Installing the processor................................................................................................................................................. 52
Base cover............................................................................................................................................................................53
Removing the base cover.............................................................................................................................................53
Installing the base cover............................................................................................................................................... 55
Power supply unit - PSU.................................................................................................................................................... 56
Removing the power supply unit -PSU...................................................................................................................... 56
Installing the power supply unit -PSU.........................................................................................................................58
Power supply unit fan - PSU fan.......................................................................................................................................59
Removing the power supply unit fan -PSU fan.........................................................................................................59
Installing the power supply unit -PSU fan.................................................................................................................. 60
Input and Output bracket....................................................................................................................................................61
Removing the Input and Output bracket.................................................................................................................... 61
Installing the Input and Output bracket...................................................................................................................... 63
System board.......................................................................................................................................................................64
Removing the system board........................................................................................................................................ 64
Installing the system board...........................................................................................................................................67
Speakers............................................................................................................................................................................... 70
Removing the speakers.................................................................................................................................................70
Installing the speakers....................................................................................................................................................71
Power button board............................................................................................................................................................ 72
Removing the power button board............................................................................................................................. 72
Installing the power button board................................................................................................................................73
Microphones.........................................................................................................................................................................74
Removing the microphones..........................................................................................................................................74
Installing the microphones............................................................................................................................................ 75
Input and Output board...................................................................................................................................................... 76
Removing the Input and Output board....................................................................................................................... 76
Installing the input and output board...........................................................................................................................78
4
Contents
Headset port........................................................................................................................................................................ 80
Removing the headset port..........................................................................................................................................80
Installing the headset port.............................................................................................................................................81
Antennas...............................................................................................................................................................................82
Removing the antennas................................................................................................................................................ 82
Installing the antennas.................................................................................................................................................. 83
Display panel.........................................................................................................................................................................84
Removing the display panel..........................................................................................................................................84
Installing the display panel............................................................................................................................................ 86
Display cable.........................................................................................................................................................................88
Removing the display cable..........................................................................................................................................88
Installing the display cable............................................................................................................................................ 89
Middle frame........................................................................................................................................................................ 90
Removing the middle frame......................................................................................................................................... 90
Installing the middle frame............................................................................................................................................92
5 Troubleshooting your computer...................................................................................................95
Enhanced Pre-Boot System Assessment — ePSA diagnostics................................................................................... 95
Running the ePSA Diagnostics.................................................................................................................................... 95
Diagnostics........................................................................................................................................................................... 95
LCD built in self test - BIST................................................................................................................................................96
6 Getting help...............................................................................................................................98
Contacting Dell.................................................................................................................................................................... 98
Contents
5
Working on your computer
Topics:
Safety instructions
Turning off your computer — Windows 10
Before working inside your computer
After working inside your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
You have read the safety information that shipped with your computer.
A component can be replaced or, if purchased separately, installed by performing the removal procedure in the reverse order.
NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
NOTE: Before working inside your computer, read the safety information that shipped with your computer. For
additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/
regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and
simple repairs as authorized in your product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow
the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching
an unpainted metal surface that is grounded to ground yourself before you touch the computer to perform any
disassembly tasks.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by
its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables
have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you
disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also,
before you connect a cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Turning off your computer — Windows 10
CAUTION:
To avoid losing data, save and close all open files and exit all open programs before you turn off your
computer or remove the side cover.
1. Click or tap .
2. Click or tap
and then click or tap Shut down.
1
6 Working on your computer
NOTE: Ensure that the computer and all attached devices are turned off. If your computer and attached devices did
not automatically turn off when you shut down your operating system, press and hold the power button for about 6
seconds to turn them off.
Before working inside your computer
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer.
3. Disconnect all network cables from the computer (if available).
CAUTION: If your computer has an RJ45 port, disconnect the network cable by first unplugging the cable from your
computer.
4. Disconnect your computer and all attached devices from their electrical outlets.
5. Open the display.
6. Press and hold the power button for few seconds, to ground the system board.
CAUTION: To guard against electrical shock unplug your computer from the electrical outlet before performing Step
# 8.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface at the same time as touching a connector on the back of the computer.
7. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
After working inside your computer
After you complete any replacement procedure, ensure that you connect external devices, cards, and cables before turning on your
computer.
CAUTION:
To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use
batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.
2. Connect any telephone or network cables to your computer.
CAUTION:
To connect a network cable, first plug the cable into the network device and then plug it into the
computer.
3. Connect your computer and all attached devices to their electrical outlets.
4. Turn on your computer.
Working on your computer
7
Technology and components
This chapter details the technology and components available in the system.
Topics:
DDR4
USB features
HDMI
DDR4
DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512
GB in capacity, compared to the DDR3's maximum capacity of 128 GB per DIMM. DDR4 synchronous dynamic random-access memory is
keyed differently from both SDRAM and DDR to prevent the user from installing the wrong type of memory into the system.
DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. DDR4 also
supports a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep
power-down mode is expected to reduce standby power consumption by 40 to 50 percent.
Key Specifications
The following table lists the specifications' comparison between DDR3 and DDR4:
Table 1. DDR3 vs DDR4
Feature/Option DDR3 DDR4 DDR 4 Advantages
Chip Densities 512 Mb-8 Gb 4 Gb-16 Gb Larger DIMM capacities
Data rates 800 Mb/s-2133 Mb/s 1600 Mb/s-3200 Mb/s Migration to higher speed I/O
Voltage 1.5 V 1.2 V Reduced memory power
demand
Low voltage standard Yes (DDR3L at 1.35V) Anticipated at 1.05V Memory Power Reductions
Internal banks 8 16 Higher data rates
Bank groups (BG) 0 4 Faster burst accesses
VREF inputs 2 —DQs and CMD/ADDR 1 — CMD/ADDR VREFDQ Now Internal
tCK — DLL Enabled 300 Mhz-800 Mhz 667Mhz-1.6Ghz Higher data rates
tCK — DLL Disabled 10MHz – 125MHz (optional) Undefined to 125MHz DLL-off now fully supported
Read Latency AL+CL AL+CL Expanded values
Write Latency AL+CWL AL+CWL Expanded values
DQ Driver (ALT) 40&Omega 48&Omega Optimal for PtP Applications
DQ Bus SSTL15 POD12 Less I/O Noise and Power
RTT Values (in &Omega) 120,60,40,30,20 240,120,80,60,48,40,34 Support for higher data rates
RTT not allowed READ Bursts Disables during READ Bursts Ease of use
ODT Modes Nominal, Dynamic Nominal, Dynamic,Park Add’l Control Mode; OTF Value
Change
ODT Control ODT Signaling Required ODT Signaling Not Required Ease of ODT Control; Allows
Non-ODT Routing, PtP Apps
2
8 Technology and components
Feature/Option DDR3 DDR4 DDR 4 Advantages
Multi-Purpose Register Four Registers – 1 Defined, 3
RFU
Four Registers – 3 Defined, 1
RFU
Provides Additional Specialty
Readout
DIMM Types RDIMM, LRDIMM, UDIMM,
SODIMM
RDIMM, LRDIMM, UDIMM,
SODIMM
DIMM Pins 240 (R, LR, U); 204 (SODIMM) 288 (R, LR, U); 260 (SODIMM)
RAS ECC CRC, Parity, Addressability,
GDM
More RAS features; improved
data integrity
DDR4 Details
There are subtle differences between DDR3 and DDR4 memory modules, as listed below.
Key notch difference
The key notch on a DDR4 module is in a different location from the key notch on a DDR3 module. Both notches are on the insertion edge,
but the notch location on the DDR4 is slightly different, to prevent the module from being installed into an incompatible board or platform.
Figure 1. Notch difference
Increased thickness
DDR4 modules are slightly thicker than DDR3, to accommodate more signal layers.
Figure 2. Thickness difference
Curved edge
DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation.
Figure 3. Curved edge
Technology and components
9
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplified the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 2. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been firmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
finally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
Higher transfer rates (up to 5 Gbps)
Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
New power management features
Full-duplex data transfers and support for new transfer types
Backward USB 2.0 compatibility
New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
Speed
Currently, there are 3 speed modes defined by the latest USB 3.0/USB 3.1 Gen 1 specification. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specification retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
USB 2.0 previously had four wires (power, ground, and a pair for differential data); USB 3.0/USB 3.1 Gen 1 adds four more for two
pairs of differential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
10
Technology and components
With today's ever increasing demands placed on data transfers with high-definition video content, terabyte storage devices, high
megapixel count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the
480Mbps theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum.
Similarly, USB 3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with
overheads. At this speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will find its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
USB 3.0/USB 3.1 Gen 1 Solid-state Drives
USB 3.0/USB 3.1 Gen 1 RAIDs
Optical Media Drives
Multimedia Devices
Networking
USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 specifies new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent
Service Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in
Windows 7, SuperSpeed support would trickle down to Vista. Microsoft has confirmed this by stating that most of their partners share the
opinion that Vista should also support USB 3.0/USB 3.1 Gen 1.
Technology and components
11
HDMI
This topic explains the HDMI 1.4/ 2.0 and its features along with the advantages.
HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-definition video, plus multichannel digital audio
on a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
HDMI 1.4 - HDMI 2.0 Features
HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio
system, eliminating the need for a separate audio cable
3D - Defines input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema
systems used in many commercial movie theaters
HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique
demands of the motoring environment while delivering true HD quality
Advantages of HDMI
Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-effective manner
Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
12
Technology and components
Major components of your system
Major components of your system
1. Stand
2. Hard drive
3. Camera assembly cover
4. Heat sink
5. System fan
6. Speakers
7. Memory module
8. Input and Output bracket
9. Input and Output board shield
10. Input and Output board
11. Headset port
12. Middle frame
13. Microphone
14. Display assembly
15. Power button board
16. Display panel
17. Power supply unit - PSU
3
Major components of your system 13
18. WLAN card
19. WLAN card shield
20. Power supply unit fan - PSU fan
21. System board
22. Processor
23. Pop-Up Camera
24. System board shield
25. DIMM door
26. Base cover
27. Back cover
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative
for purchase options.
14 Major components of your system
Removing and Installing components
Topics:
Recommended tools
Screw size list
System board layout
Rubber feet
Cable cover - optional
Stand
Back cover
Hard drive
Memory module
System board shield
Intel Optane
Solid State Drive -SSD
Solid State Drive -2230
WLAN card
System fan
Heat sink
Pop-Up Camera
Coin cell battery
Processor
Base cover
Power supply unit - PSU
Power supply unit fan - PSU fan
Input and Output bracket
System board
Speakers
Power button board
Microphones
Input and Output board
Headset port
Antennas
Display panel
Display cable
Middle frame
Recommended tools
The procedures in this document require the following tools:
Phillips #0 screwdriver
Phillips #1 screwdriver
Plastic scribe
NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4
4
Removing and Installing components 15
Screw size list
Table 3. OptiPlex 7470 All-in-One
Component Screw type Quantity Screw image
Cable cover M3x9 1
System board shield M3x5 5
Solid-state drive/Intel Optane
card
M2x2.5 1
WLAN card shield M2x2.5 2
WLAN card M2x2.5 1
System fan M3x5 3
Pop-up camera assembly M3x5 2
Pop-up camera bezel M3x5 3
Base cover M3x5 4
PSU cable M3x5 1
Power supply unit—PSU M3x5 1
Power supply unit fan—PSU fan M3x5 2
Input and Output bracket M3x5 3
System board M3x5 9
Speakers M3x4+7.1 6
Power button board M3x5 1
16 Removing and Installing components
Component Screw type Quantity Screw image
Microphones (2 modules) M2x2.5 2
Input and Output board shield M3x5 2
Input and Output board M3x5 2
Headset port M3x5 1
Antennas M2x2.5 2
Display panel M3x5 11
Middle frame M3x5 15
System board layout
OptiPlex 7470 All-in-One
Removing and Installing components
17
1. PSU power connector 2. Processor
3. Memory slots 4. Back light connector
5. Webcam connector 6. M.2 PCIe/SATA slot
7. System fan connector 8. LPC_Debug
9. Service mode jumper/Password clear jumper/CMOS clear
jumper
10. SATA HDD connector
11. SPI header 12. SIO_signal connector
13. SIO_power connector 14. UAJ connector
15. INT_SPK connector 16. DMIC connector
17. Coin cell battery 18. Power board button connector
19. LVDS connector 20. M.2 WLAN slot
21. PSU fan 22. eDP cable connector
23. Touch cable connector
Rubber feet
18
Removing and Installing components
Removing the rubber feet
1. Follow the procedure in Before working inside your computer.
2. Remove the Stand.
3. Pry the rubber feet at the bottom edge from the display assembly base and pull it out.
Installing the rubber feet
1. Align the rubber feet with the slots on the display assembly base and push it firmly in place.
Removing and Installing components
19
2. Install the Stand.
3. Follow the procedure in After working inside your computer
Cable cover - optional
Removing the cable cover
1. Follow the procedure in Before working inside your computer.
2. Remove the Stand.
3. Remove the single (M3x9) screw that secures the cable cover to the base cover [1].
4. Lift the cable cover off the base cover [2].
20
Removing and Installing components
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98

Dell OptiPlex 7470 All-In-One Owner's manual

Category
All-in-One workstations
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI