Bodyworx A732 Owner's manual

Bodyworx
Brand
Bodyworx
Model
A732
Category
Fitness, gymnastics & weight training
Type
Owner's manual

This manual is also suitable for

1
Retain this owner’s manual for future reference
Read and follow all instructions in this owner’s manual
Version A
Owner’s Manual
BODYWORX
BODY WORX
Model No: A932
Step Through
Recumbent
Safety Instructions
• To ensure the best safety of the exerciser, regularly
check it
on damages and worn parts.
• If you pass on this exerciser to another person or if
you allow another perso
n to use it, make sure that
that person is familiar with the content and
instructions in these instructions.
•
Only one person should use the exerciser at a time.
• Before the first use and regularly make sure that all
screws, bolt
s and other joints are properly tightened
and firmly seated.
• Before you start your work-out, remove all
sharp-edge
d objects around the exerciser.
• Only use the exercise for your work-out if it works
flawlessly
.
• Any broken, worn or defective part must immediately
be replaced
and/or the exerciser must no longer be
used until it has been properly maintained and
repaired.
• Parents and other supervisory persons should be
aware of their responsib
ility, due to situations which
may arise for which the exerciser has not been
designed and which may occur due to children’s
natural play instinct and interest in experimenting.
• If you do allow children to use this exerciser, be sure
to t
ake into consideration and assess their mental
and physical condition and development, and above
all their temperament. Children should use the
exerciser only under adult supervision and be
instructed on the correct and proper use of the
exerciser. The exerciser is not a toy.
• Make sure there is sufficient free space around the
exerciser when you set it up.
• To avoid possible accidents, do not allow children
to approach
the exerciser without supervision,
since they may use it in a way for which it is not
intended due to their natural play instinct and
interest in experimenting.
• Please note that an improper and excessive
work-out ma
y be harmful to your health.
• Please note that levers and other adjustment
mechanisms are not pr
ojecting into the area of
movement during the work-out.
• When setting up the exerciser, please make
sure that the
exerciser is standing in a stable
way and that any possible unevenness of the
floor is evened out.
• Always wear appropriate clothing and shoes
which are suit
able for your work-out on the
exerciser. The clothes must be designed in a
way so that they will not get caught in any part of
the exerciser during the work-out due to their
form (for example, length). Be sure to wear
appropriate shoes which are suitable for the
work-out, firmly support the feet and which are
provided with a non-slip sole.
• Be sure to consult a physician before you start
any exercise program. He ma
y give you proper
hints and advice with respect to the individual
intensity of stress for you as well as to your
work-out and sensible eating habits.
Important Notes
• Assemble the exerciser as per assembly instructions and be sure
to only use the structural p
arts provided with the exerciser and
designed for it. Prior to the assembly, make sure the contents of
the delivery are complete by referring to the parts list of the
assembly and operating instructions.
• Be sure to set up the exerciser in a dry and even place and
always protect it from humidity
. If you wish to protect the place
particularly against pressure points, contamination, etc., it is
recommended to put a suitable, non-slip mat under the exerciser.
• The general rule is that exercisers and training devices are no
toys.
Therefore, they must only be used by properly informed or
instructed persons.
•
Stop your work-out immediately in case of dizziness, nausea, chest
pain or any other physical symptoms. In case of doubt, consult your
physician immediately.
• Children, disabled and handicapped persons should use the
exercise only under supervision and in presence
of another
person who may give support and useful instructions.
• Be sure that your body parts and those of other persons are
never close
to any moving parts of the exerciser during its use.
• When adjusting the adjustable parts, make sure they are
adjusted pro
perly and note the marked, maximum adjusting
position, for example of the saddle support, respectively.
• Do not work out immediately after meals!
Exploded drawing:
6
51
48L
42
21
88
9
13
7
13
14
13
8
45
63
56
13
10
68
69
70R
75
76
61
77
78
76
34
83
81
82
80
85
60
66
90
79
34
33
37L
72
73
99
84
100
48R
17
11
12R
12L
71
56
70L
19
41
67
49
1
2
10
38
74
62
96
94
30
87
62
74
4R
86
18
35
98
13
7
9
15R
16R
23
22
37R
57 97 25 59 55 20
91
92
93
95
5
11
47
46 50 52A 53 67
54
40
13
14
64
36
92
26
4L
101
103
102
102
105 10452B
107
84
14
109
110
108
4
Part list:
Part No. Description Qty Part No. Description Qty
1 Main frame 1 30 End cap D25.4x31L 2
2 Rear stabilizer
1
31 Idle fixing plate 1
3 Front stabilizer 1 32 Spring D3*D17*65L 1
4L Left rear foot cap (triangle) 1 33 Idle D23.8xD38x24 1
4R Right rear foot cap (triangle) 1 34 Nylon nut M10x1.5x10T 1
5 Handlebar post 1 35 Spacer D22.5*D17.2*6.4T 1
6 Sliding beam 1 36 Nylon nut M8*1.25*8T 1
7
Spring washer
D15.4xD8.2x2T 8 37L Left chain cover 1
8 Allen bolt M8*1.25*40 4 37R Right chain cover 1
9 Allen bolt M8*1.25*20L 12 38 Backrest 1
10 Nylon nut M8*1.25*8T 12 39 Motor 1
11
Curved washer
D22*D8.5*1.5T 5 40 Tension cable 1
12L Left chain cover 1 41 Adjustable tube 1
12R Right chain cover 1 42 Seat 1
13 Flat washer D16xD8.5x1.2T 22 43 Foot cap (transfer) 1
14 Allen bolt M8x1.25x15L 15 44 Foot cap (adjustable) 1
15L Left crank 1 45 Square end cap25*25*13L 4
15R Right crank 1 46 Upper hand pulse cable 750L 2
16L\R Pedal sets JD-22A 1 47 Lower hand pulse cable 1800L 1
17 Allen bolt M8*1.25*70 4 48L Left handlebar welding set 1
18 Crank axle welding set 1 48R Right handlebar welding set 1
19 C-ring S-16(1T) 2 49 Buffer D20*10L*M8*1.25 2
20 Bolt M6x1.0x15L 4 50 Middle hand pulse cable 900L 2
21 Nylon nut M6x1.0x6T 4 51 Bushing125*75*53 2
22 Bolt M8x1.25x25 2 52A Upper computer cable 750L 1
23 Cover for bolt D23x6.5 2 52B Lower computer cable 600L 1
24 Bearing#6003ZZ 2 53 Sensor cable 200L 1
25 Multi-groove belt 1 54 Handle pulse cable 800L 1
26 Magnet system 1 55 Pulley 1
27 Flat washer D22*D10*2T 1 56 Handle pulse 2
28 Anti-loosen nut3/8"-26UNFx6.5T 2 57 Waved washer D22xD17x0.3T 2
29 Flat washer D25*D8.5*2.0T 1 58 Bolt M8*1.25*25L 1
5
59 Round magnet 1 92 Plastic flat washer D50*D10*1.0T 3
60 Computer SM-2780 1 93 Axle cover D60*13.5L 2
61 Flat washer D24xD16x1.5T 2 94 Side cover D29.1*13L 2
62 Foam D23*4T*560L 2 95 Nylon nut M8*1.25*8T 1
63 Semi-ball end plug D25.4x28L 2 96 Bolt M8*1.25*60L 1
64 Upper protective cover 1 97 C ring S-17(1T) 1
65 Screw ST4*1.41*15L 8 98 Flat washer D23*D17.2*1.5T 1
66 Cross bolt M5*10L 4 99 Decorative cover for backrest 1
67 Cross bolt M5*0.8*10L 3 100 Cross bolt M6*1.0*25L 4
68 Backrest supporting tube 1 101 Hidden pin 1
69 Square end cap 2 102 Cross screw ST4.2x1.4x20L 17
70L Left fixing plate 1 103 Cross screw ST4.2*20L 2
70R Right fixing plate 1 104 Adaptor 1
71 Rear decorative cover 1 105 Electric cable900L 1
72 Front decorative cover 1 106 Cross screw ST4.2*1.4*15L 4
73 Round cross screw ST4x20L 2 107 Chest belt 1
74 Round end cap 2 108 Holder of bottle 1
75 Knob 1 109 Bottle 1
76 C ring S-12(1T) 3 110 Bolt 1
77 Spacer D19xD13.1x4T 1
78 Axle D15.9*D13*219L 1
79 Flat washer D24*D13.5*2.5T 1
80 Bushing D29*D12.1*9T 2
81 Buffer40.5*28.5*6T 1
82 Stopper tube 1
83 Small protective cover 1
84 Round end cap 5
85 Foam 1
86 Adjustable round wheel 2
87 Foam D10*3T*245L 1
88 Seat post 1
89 Plastic cover D3*30L 2
90 Computer fixing base 1
91 Oval end cap 1
6
STEP 1
2
13
7
9
(a)
FIG.1
M8*20L
D15.4*D8.2*2T
(A)x8
D16*D8.5*1.2T
1. Fix the front stabilizer (3) and rear stabilizer (2) onto the main frame by using
Bolt (9), spring washer (7) and flat washer (13).
2. Adjust the balance by turning the wheel of rear foot cap.
7
STEP 2
64
11
13
14
1
64
(a)
52B
52A
46
50
FIG.2
D22*D8.5*1.5T
M8*15L
D16*D8.5*1.2T
(x1)
a
M8*15L
(x2)
b
5
5
(B)
1. Pick up the upper protective cover (64)
2.
Join with 2 sets of cables: upper computer cable (52A) and lower
computer cable (52B),
upper & middle hand pul
se cable (46 & 50)
3. Place the protective cover and fix the handlebar post by using bolt (14), flat washer (13)
and curved washer (11).
8
STEP 3
FIG.3
M5*0.8*10L
60
66
52A
46
5
60
(a)
/
/
5
5
46
16L
15R
15L
16R
(C)x4
104
107
1. Connect with the upper pulse cable (46) & upper computer cable (52A) with computer (60
)
2.
Fix the computer by screw (66).
3. Assemble the left & right pedal (16L&16R) with left & ri
ght crank (15R & 15L).
9
STEP 4
48R
54
FIG.4
M8*8T
M8*70L
D22*D8.5*1.5T
D16*D8.5*1.2T
48L
11
17
10
13
54
47
(D)x4
1. Fix the left & right handlebar (48L&48R) to the main frame by using bolt (17), curved
washer (11), flat washer (13) and domed nut (10).
2. Connect the pulse cable (54) with lower pul
se cable (47).
10
STEP 5
FIG.5
D16*D8.5*1.2T
M8*20L
M8*40L
(x4)
a
(x4)
b
D16*D8.5*1.2T
9
13
68
38
42
13
8
(E)
1. Fix the seat pad (42) onto the support tube by using bolt (8), flat washer (13)
2.
Attached the backrest (38) onto support tube (68) by using bolt (9), flat washer (13) .
11
STEP 6
99
FIG.6
M6*1*25L
38
84
100
D19*17
(F)
109
110
108
M5*0.8*15L
(x4)
a
(x2)
b
1. Fix the decorative cover (99) on the back of back pad (38) by bolt (100)
2.
Plug the round end cap (84).
3. Fix the bottle (109) to the holder of bottle (108) by using screw (110).
12
STEP 7
1. Adjust the position of seat pad front and back.
2. Turning the knob to get the comfortable back pad position.
13
Computer Operation Instructions
SM-2780-71
BUTTON FUNCTION:
MODE/ENTER :
In stop mode, the mode is to confirm all exercise data setting, and enter into
program.
In stop mode, press the button back to main menu.
RESET :
To start or stop exercise.
START/STOP :
To test hear rate recovery status.
RECOVERY :
To select training mode and adjust function value up.
UP :
To select training mode and adjust function value down.
DOWN :
For body fat measurement
BODY FAT :
DISPLAY EXERCISE DATA:
TIME :
Display range 0:00~99:99 ; Setting range 0:00~99:00
Display range 0.00~99.99 ; Setting range 0.00~99.90km
DISTANCE :
Display range 0~9999 ; Setting range 0.00~9990
CALORIES :
Display range P-30~240 ; Setting range 0-30~240
PULSE :
Display range 0~999 ; Setting range 10~350
WATT :
0~99.9km
SPEED :
0~999
RPM :
14
OPERATION PROCEDURE
1. Connect power supply and computer will power on with a long beep sound, LCD display all segments (drawing A)
for 2 seconds and enter into personal data setting mode (gender, age, height and weight) for U1~U4. (drawing B~C)
2. After user data set up, computer will display main menu (drawing D).
Drawing A Drawing B
Drawing C Drawing D
3. In main menu, first exercise program MANUAL will flash, user may press UP and DOWN button to select MANUAL
ÆPROGRAM (12 profiles) (drawing E)ÆPROGRAMÆUSER PRO
GRAMÆ HRCÆWATT.
Drawing E Drawing F
4. Quick Start and Manual :
Before exercise in Man
ual mode, user my set up TIME, DISTANCE,
CALORIES and PULSE target.
After power on, user may press START/STOP button to start exercise in MANUAL immediately without any setting.
Level can be adjusted during exercise by press UP or DOWN.
5. PROGRAM :
Before exercise in Progr
am mode, u
ser may set up TIME target.
Press UP and DOWN to select Program with 12 profiles and press ENTER/MODE to confirm. Level can be adjusted
during exercise by press UP or DOWN.
15
6. H.R.C. :
Before exercise, computer will ask for user AGE first to calculate TARGET pulse. User may still press UP and
DOWN to change target pulse from 30 to 240.
7. USER PROGRAM :
User may press UP, DOWN and then press MODE to create his own profile. (from column 1 to column 20) User
may hold on pressing MODE button for 2 seconds to quit profile setting.
8. WATT :
The preset watt value 120 is flashin
g on screen in WATT setting mode. User may use UP, DOWN button to set
target value from 10 to 350. Press MODE button for confirm.
Alpha-numeric display user’s selected program name (Manual→Program→User→HRC→
WATT) to remind user he/she is under which workout program.
Brick area display total 8 rolls and every profile are composing of 20 rolls.
While exercise, profile display shall rolling for every rolls until user finish
exercise fo
r it selected profile.
NOTE:
1. This computer require 9V, 0.5mA adaptor.
2. When user stop pedaling for 4 minutes, computer will enter into power save mode, all setting
and exercise data will
stored until user start exercise again.
3. When computer act abnormal, please plug out the adaptor and plug in again.
16
BODYWORX
BODY WORX
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Bodyworx A732 Owner's manual

Bodyworx
Brand
Bodyworx
Model
A732
Category
Fitness, gymnastics & weight training
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents