Bodyworx A732 Owner's manual

1

Retain this owner’s manual for future reference

Read and follow all instructions in this owner’s manual

Version A

Owner’s Manual

BODYWORX

BODY WORX

Model No: A932

Step Through

Recumbent

Safety Instructions

• To ensure the best safety of the exerciser, regularly

check it

on damages and worn parts.

• If you pass on this exerciser to another person or if

you allow another perso

n to use it, make sure that

that person is familiar with the content and

instructions in these instructions.

•

Only one person should use the exerciser at a time.

• Before the first use and regularly make sure that all

screws, bolt

s and other joints are properly tightened

and firmly seated.

• Before you start your work-out, remove all

sharp-edge

d objects around the exerciser.

• Only use the exercise for your work-out if it works

flawlessly

.

• Any broken, worn or defective part must immediately

be replaced

and/or the exerciser must no longer be

used until it has been properly maintained and

repaired.

• Parents and other supervisory persons should be

aware of their responsib

ility, due to situations which

may arise for which the exerciser has not been

designed and which may occur due to children’s

natural play instinct and interest in experimenting.

• If you do allow children to use this exerciser, be sure

to t

ake into consideration and assess their mental

and physical condition and development, and above

all their temperament. Children should use the

exerciser only under adult supervision and be

instructed on the correct and proper use of the

exerciser. The exerciser is not a toy.

• Make sure there is sufficient free space around the

exerciser when you set it up.

• To avoid possible accidents, do not allow children

to approach

the exerciser without supervision,

since they may use it in a way for which it is not

intended due to their natural play instinct and

interest in experimenting.

• Please note that an improper and excessive

work-out ma

y be harmful to your health.

• Please note that levers and other adjustment

mechanisms are not pr

ojecting into the area of

movement during the work-out.

• When setting up the exerciser, please make

sure that the

exerciser is standing in a stable

way and that any possible unevenness of the

floor is evened out.

• Always wear appropriate clothing and shoes

which are suit

able for your work-out on the

exerciser. The clothes must be designed in a

way so that they will not get caught in any part of

the exerciser during the work-out due to their

form (for example, length). Be sure to wear

appropriate shoes which are suitable for the

work-out, firmly support the feet and which are

provided with a non-slip sole.

• Be sure to consult a physician before you start

any exercise program. He ma

y give you proper

hints and advice with respect to the individual

intensity of stress for you as well as to your

work-out and sensible eating habits.

Important Notes

• Assemble the exerciser as per assembly instructions and be sure

to only use the structural p

arts provided with the exerciser and

designed for it. Prior to the assembly, make sure the contents of

the delivery are complete by referring to the parts list of the

assembly and operating instructions.

• Be sure to set up the exerciser in a dry and even place and

always protect it from humidity

. If you wish to protect the place

particularly against pressure points, contamination, etc., it is

recommended to put a suitable, non-slip mat under the exerciser.

• The general rule is that exercisers and training devices are no

toys.

Therefore, they must only be used by properly informed or

instructed persons.

•

Stop your work-out immediately in case of dizziness, nausea, chest

pain or any other physical symptoms. In case of doubt, consult your

physician immediately.

• Children, disabled and handicapped persons should use the

exercise only under supervision and in presence

of another

person who may give support and useful instructions.

• Be sure that your body parts and those of other persons are

never close

to any moving parts of the exerciser during its use.

• When adjusting the adjustable parts, make sure they are

adjusted pro

perly and note the marked, maximum adjusting

position, for example of the saddle support, respectively.

• Do not work out immediately after meals!

Exploded drawing:

6

51

48L

42

21

88

9

13

7

13

14

13

8

45

63

56

13

10

68

69

70R

75

76

61

77

78

76

34

83

81

82

80

85

60

66

90

79

34

33

37L

72

73

99

84

100

48R

17

11

12R

12L

71

56

70L

19

41

67

49

1

2

10

38

74

62

96

94

30

87

62

74

4R

86

18

35

98

13

7

9

15R

16R

23

22

37R

57 97 25 59 55 20

91

92

93

95

5

11

47

46 50 52A 53 67

54

40

13

14

64

36

92

26

4L

101

103

102

105 10452B

107

84

14

109

110

108

4

Part list:

Part No. Description Qty Part No. Description Qty

1 Main frame 1 30 End cap D25.4x31L 2

2 Rear stabilizer

1

31 Idle fixing plate 1

3 Front stabilizer 1 32 Spring D3*D17*65L 1

4L Left rear foot cap (triangle) 1 33 Idle D23.8xD38x24 1

4R Right rear foot cap (triangle) 1 34 Nylon nut M10x1.5x10T 1

5 Handlebar post 1 35 Spacer D22.5*D17.2*6.4T 1

6 Sliding beam 1 36 Nylon nut M8*1.25*8T 1

7

Spring washer

D15.4xD8.2x2T 8 37L Left chain cover 1

8 Allen bolt M8*1.25*40 4 37R Right chain cover 1

9 Allen bolt M8*1.25*20L 12 38 Backrest 1

10 Nylon nut M8*1.25*8T 12 39 Motor 1

11

Curved washer

D22*D8.5*1.5T 5 40 Tension cable 1

12L Left chain cover 1 41 Adjustable tube 1

12R Right chain cover 1 42 Seat 1

13 Flat washer D16xD8.5x1.2T 22 43 Foot cap (transfer) 1

14 Allen bolt M8x1.25x15L 15 44 Foot cap (adjustable) 1

15L Left crank 1 45 Square end cap25*25*13L 4

15R Right crank 1 46 Upper hand pulse cable 750L 2

16L\R Pedal sets JD-22A 1 47 Lower hand pulse cable 1800L 1

17 Allen bolt M8*1.25*70 4 48L Left handlebar welding set 1

18 Crank axle welding set 1 48R Right handlebar welding set 1

19 C-ring S-16(1T) 2 49 Buffer D20*10L*M8*1.25 2

20 Bolt M6x1.0x15L 4 50 Middle hand pulse cable 900L 2

21 Nylon nut M6x1.0x6T 4 51 Bushing125*75*53 2

22 Bolt M8x1.25x25 2 52A Upper computer cable 750L 1

23 Cover for bolt D23x6.5 2 52B Lower computer cable 600L 1

24 Bearing#6003ZZ 2 53 Sensor cable 200L 1

25 Multi-groove belt 1 54 Handle pulse cable 800L 1

26 Magnet system 1 55 Pulley 1

27 Flat washer D22*D10*2T 1 56 Handle pulse 2

28 Anti-loosen nut3/8"-26UNFx6.5T 2 57 Waved washer D22xD17x0.3T 2

29 Flat washer D25*D8.5*2.0T 1 58 Bolt M8*1.25*25L 1

5

59 Round magnet 1 92 Plastic flat washer D50*D10*1.0T 3

60 Computer SM-2780 1 93 Axle cover D60*13.5L 2

61 Flat washer D24xD16x1.5T 2 94 Side cover D29.1*13L 2

62 Foam D23*4T*560L 2 95 Nylon nut M8*1.25*8T 1

63 Semi-ball end plug D25.4x28L 2 96 Bolt M8*1.25*60L 1

64 Upper protective cover 1 97 C ring S-17(1T) 1

65 Screw ST4*1.41*15L 8 98 Flat washer D23*D17.2*1.5T 1

66 Cross bolt M5*10L 4 99 Decorative cover for backrest 1

67 Cross bolt M5*0.8*10L 3 100 Cross bolt M6*1.0*25L 4

68 Backrest supporting tube 1 101 Hidden pin 1

69 Square end cap 2 102 Cross screw ST4.2x1.4x20L 17

70L Left fixing plate 1 103 Cross screw ST4.2*20L 2

70R Right fixing plate 1 104 Adaptor 1

71 Rear decorative cover 1 105 Electric cable900L 1

72 Front decorative cover 1 106 Cross screw ST4.2*1.4*15L 4

73 Round cross screw ST4x20L 2 107 Chest belt 1

74 Round end cap 2 108 Holder of bottle 1

75 Knob 1 109 Bottle 1

76 C ring S-12(1T) 3 110 Bolt 1

77 Spacer D19xD13.1x4T 1

78 Axle D15.9*D13*219L 1

79 Flat washer D24*D13.5*2.5T 1

80 Bushing D29*D12.1*9T 2

81 Buffer40.5*28.5*6T 1

82 Stopper tube 1

83 Small protective cover 1

84 Round end cap 5

85 Foam 1

86 Adjustable round wheel 2

87 Foam D10*3T*245L 1

88 Seat post 1

89 Plastic cover D3*30L 2

90 Computer fixing base 1

91 Oval end cap 1

6

STEP 1

2

13

7

9

(a)

FIG.1

M8*20L

D15.4*D8.2*2T

(A)x8

D16*D8.5*1.2T

1. Fix the front stabilizer (3) and rear stabilizer (2) onto the main frame by using

Bolt (9), spring washer (7) and flat washer (13).

2. Adjust the balance by turning the wheel of rear foot cap.

7

STEP 2

64

11

13

14

1

64

(a)

52B

52A

46

50

FIG.2

D22*D8.5*1.5T

M8*15L

D16*D8.5*1.2T

(x1)

a

M8*15L

(x2)

b

5

(B)

1. Pick up the upper protective cover (64)

2.

Join with 2 sets of cables: upper computer cable (52A) and lower

computer cable (52B),

upper & middle hand pul

se cable (46 & 50)

3. Place the protective cover and fix the handlebar post by using bolt (14), flat washer (13)

and curved washer (11).

8

STEP 3

FIG.3

M5*0.8*10L

60

66

52A

46

5

60

(a)

/

5

46

16L

15R

15L

16R

(C)x4

104

107

1. Connect with the upper pulse cable (46) & upper computer cable (52A) with computer (60

)

2.

Fix the computer by screw (66).

3. Assemble the left & right pedal (16L&16R) with left & ri

ght crank (15R & 15L).

9

STEP 4

48R

54

FIG.4

M8*8T

M8*70L

D22*D8.5*1.5T

D16*D8.5*1.2T

48L

11

17

10

13

54

47

(D)x4

1. Fix the left & right handlebar (48L&48R) to the main frame by using bolt (17), curved

washer (11), flat washer (13) and domed nut (10).

2. Connect the pulse cable (54) with lower pul

se cable (47).

10

STEP 5

FIG.5

D16*D8.5*1.2T

M8*20L

M8*40L

(x4)

a

(x4)

b

D16*D8.5*1.2T

9

13

68

38

42

13

8

(E)

1. Fix the seat pad (42) onto the support tube by using bolt (8), flat washer (13)

2.

Attached the backrest (38) onto support tube (68) by using bolt (9), flat washer (13) .

11

STEP 6

99

FIG.6

M6*1*25L

38

84

100

D19*17

(F)

109

110

108

M5*0.8*15L

(x4)

a

(x2)

b

1. Fix the decorative cover (99) on the back of back pad (38) by bolt (100)

2.

Plug the round end cap (84).

3. Fix the bottle (109) to the holder of bottle (108) by using screw (110).

12

STEP 7

1. Adjust the position of seat pad front and back.

2. Turning the knob to get the comfortable back pad position.

13

Computer Operation Instructions

SM-2780-71

BUTTON FUNCTION:

MODE/ENTER :

In stop mode, the mode is to confirm all exercise data setting, and enter into

program.

In stop mode, press the button back to main menu.

RESET :

To start or stop exercise.

START/STOP :

To test hear rate recovery status.

RECOVERY :

To select training mode and adjust function value up.

UP :

To select training mode and adjust function value down.

DOWN :

For body fat measurement

BODY FAT :

DISPLAY EXERCISE DATA:

TIME :

Display range 0:00~99:99 ; Setting range 0:00~99:00

Display range 0.00~99.99 ; Setting range 0.00~99.90km

DISTANCE :

Display range 0~9999 ; Setting range 0.00~9990

CALORIES :

Display range P-30~240 ; Setting range 0-30~240

PULSE :

Display range 0~999 ; Setting range 10~350

WATT :

0~99.9km

SPEED :

0~999

RPM :

14

OPERATION PROCEDURE

1. Connect power supply and computer will power on with a long beep sound, LCD display all segments (drawing A)

for 2 seconds and enter into personal data setting mode (gender, age, height and weight) for U1~U4. (drawing B~C)

2. After user data set up, computer will display main menu (drawing D).

Drawing A Drawing B

Drawing C Drawing D

3. In main menu, first exercise program MANUAL will flash, user may press UP and DOWN button to select MANUAL

ÆPROGRAM (12 profiles) (drawing E)ÆPROGRAMÆUSER PRO

GRAMÆ HRCÆWATT.

Drawing E Drawing F

4. Quick Start and Manual :

Before exercise in Man

ual mode, user my set up TIME, DISTANCE,

CALORIES and PULSE target.

After power on, user may press START/STOP button to start exercise in MANUAL immediately without any setting.

Level can be adjusted during exercise by press UP or DOWN.

5. PROGRAM :

Before exercise in Progr

am mode, u

ser may set up TIME target.

Press UP and DOWN to select Program with 12 profiles and press ENTER/MODE to confirm. Level can be adjusted

during exercise by press UP or DOWN.

15

6. H.R.C. :

Before exercise, computer will ask for user AGE first to calculate TARGET pulse. User may still press UP and

DOWN to change target pulse from 30 to 240.

7. USER PROGRAM :

User may press UP, DOWN and then press MODE to create his own profile. (from column 1 to column 20) User

may hold on pressing MODE button for 2 seconds to quit profile setting.

8. WATT :

The preset watt value 120 is flashin

g on screen in WATT setting mode. User may use UP, DOWN button to set

target value from 10 to 350. Press MODE button for confirm.

Alpha-numeric display user’s selected program name (Manual→Program→User→HRC→

WATT) to remind user he/she is under which workout program.

Brick area display total 8 rolls and every profile are composing of 20 rolls.

While exercise, profile display shall rolling for every rolls until user finish

exercise fo

r it selected profile.

NOTE:

1. This computer require 9V, 0.5mA adaptor.

2. When user stop pedaling for 4 minutes, computer will enter into power save mode, all setting

and exercise data will

stored until user start exercise again.

3. When computer act abnormal, please plug out the adaptor and plug in again.

16

BODYWORX

BODY WORX

Bodyworx A732 Owner's manual

This manual is also suitable for

Bodyworx A732 Owner's manual

Related papers

Other documents