Cisco Systems 15310-CL User manual

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco ONS 15310-CL and

Cisco ONS 15310-MA Ethernet Card

Software Feature and Configuration Guide

Cisco IOS Release 12.2(28)SV

CTC and Documentation Release 8.5

June 2009

Text Part Number: 78-18133-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, CCSI, Cisco Eos, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase, Cisco StackPower,

Cisco StadiumVision, Cisco TelePresence, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip Mino, Flipshare (Design), Flip Ultra,

Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital,

Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and Access Registrar, Aironet, AllTouch,

AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo,

Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation,

Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the IronPort logo, Laser Link, LightStream,

Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY, PowerPanels, PowerTV, PowerTV (Design),

PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc.

and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0910R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide, Release 8.5

i

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

CONTENTS

Preface i

Revision History i

Document Objectives ii

Audience ii

Related Documentation ii

Document Conventions iii

Obtaining Optical Networking Information ix

Where to Find Safety and Warning Information ix

Cisco Optical Networking Product Documentation CD-ROM ix

Obtaining Documentation, Obtaining Support, and Security Guidelines ix

CHAPTER

1 Overview of the ML-Series Card 1-1

ML-Series Card Description 1-1

ML-Series Feature List 1-2

Key ML-Series Features 1-4

Cisco IOS 1-4

GFP-F Framing 1-4

Link Aggregation (FEC and POS) 1-5

RMON 1-5

RPR 1-5

SNMP 1-5

TL1 1-6

CHAPTER

2 CTC Operations on the ML-Series Card 2-1

Displaying ML-Series POS Statistics in CTC 2-1

Displaying ML-Series Ethernet Statistics in CTC 2-2

Displaying ML-Series Ethernet Ports Provisioning Information on CTC 2-2

Displaying ML-Series POS Ports Provisioning Information on CTC 2-3

Displaying SONET Alarms 2-4

Displaying J1 Path Trace 2-4

Provisioning SONET Circuits 2-4

Contents

ii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

CHAPTER

3 Initial Configuration of the ML-Series Card 3-1

Hardware Installation 3-1

Cisco IOS on the ML-Series Card 3-1

Opening a Cisco IOS Session Using CTC 3-2

Telnetting to the Node IP Address and Slot Number 3-2

Telnetting to a Management Port 3-3

ML-Series IOS CLI Console Port 3-4

RJ-11 to RJ-45 Console Cable Adapter 3-4

Connecting a PC or Terminal to the Console Port 3-4

Startup Configuration File 3-5

Manually Creating a Startup Configuration File Through the Serial Console Port 3-6

Passwords 3-6

Configuring the Management Port 3-6

Configuring the Hostname 3-7

Loading a Cisco IOS Startup Configuration File Through CTC 3-8

Database Restore of the Startup Configuration File 3-9

Cisco IOS Command Modes 3-9

Using the Command Modes 3-11

Exit 3-11

Getting Help 3-11

CHAPTER

4 Configuring Interfaces on the ML-Series Card 4-1

General Interface Guidelines 4-1

MAC Addresses 4-1

Interface Port ID 4-2

Basic Interface Configuration 4-3

Basic Fast Ethernet and POS Interface Configuration 4-4

Configuring the Fast Ethernet Interfaces 4-4

Configuring the POS Interfaces 4-5

Monitoring Operations on the Fast Ethernet Interfaces 4-6

CHAPTER

5 Configuring POS on the ML-Series Card 5-1

Understanding POS on the ML-Series Card 5-1

Available Circuit Sizes and Combinations 5-1

LCAS Support 5-2

J1 Path Trace, and SONET Alarms 5-2

Framing Mode, Encapsulation, Scrambling, MTU and CRC Support 5-3

Configuring the POS Interface 5-3

Contents

iii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Configuring POS Interface Framing Mode 5-4

Configuring POS Interface Encapsulation Type Under GFP-F Framing 5-5

SONET Alarms 5-6

Configuring SONET Alarms 5-6

Configuring SONET Delay Triggers 5-7

Monitoring and Verifying POS 5-8

CHAPTER

6 Configuring STP and RSTP on the ML-Series Card 6-1

STP Features 6-1

STP Overview 6-2

Supported STP Instances 6-2

Bridge Protocol Data Units 6-2

Election of the Root Switch 6-3

Bridge ID, Switch Priority, and Extended System ID 6-4

Spanning-Tree Timers 6-4

Creating the Spanning-Tree Topology 6-5

Spanning-Tree Interface States 6-5

Blocking State 6-6

Listening State 6-7

Learning State 6-7

Forwarding State 6-7

Disabled State 6-7

Spanning-Tree Address Management 6-8

STP and IEEE 802.1Q Trunks 6-8

Spanning Tree and Redundant Connectivity 6-8

Accelerated Aging to Retain Connectivity 6-9

RSTP Features 6-9

Supported RSTP Instances 6-9

Port Roles and the Active Topology 6-10

Rapid Convergence 6-11

Synchronization of Port Roles 6-12

Bridge Protocol Data Unit Format and Processing 6-13

Processing Superior BPDU Information 6-14

Processing Inferior BPDU Information 6-14

Topology Changes 6-14

Interoperability with IEEE 802.1D STP 6-15

Configuring STP and RSTP Features 6-15

Default STP and RSTP Configuration 6-16

Disabling STP and RSTP 6-16

Contents

iv

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Configuring the Root Switch 6-17

Configuring the Port Priority 6-17

Configuring the Path Cost 6-18

Configuring the Switch Priority of a Bridge Group 6-18

Configuring the Hello Time 6-19

Configuring the Forwarding-Delay Time for a Bridge Group 6-20

Configuring the Maximum-Aging Time for a Bridge Group 6-20

Verifying and Monitoring STP and RSTP Status 6-20

CHAPTER

7 Configuring VLANs on the ML-Series Card 7-1

Understanding VLANs 7-1

Configuring IEEE 802.1Q VLAN Encapsulation 7-2

IEEE 802.1Q VLAN Configuration 7-3

Monitoring and Verifying VLAN Operation 7-5

CHAPTER

8 Configuring IEEE 802.1Q Tunneling and Layer 2 Protocol Tunneling on the ML-Series Card 8-1

Understanding IEEE 802.1Q Tunneling 8-1

Configuring IEEE 802.1Q Tunneling 8-4

IEEE 802.1Q Tunneling and Compatibility with Other Features 8-4

Configuring an IEEE 802.1Q Tunneling Port 8-4

IEEE 802.1Q Example 8-5

Understanding VLAN-Transparent and VLAN-Specific Services 8-6

VLAN-Transparent and VLAN-Specific Services Configuration Example 8-7

Understanding Layer 2 Protocol Tunneling 8-9

Configuring Layer 2 Protocol Tunneling 8-9

Default Layer 2 Protocol Tunneling Configuration 8-10

Layer 2 Protocol Tunneling Configuration Guidelines 8-10

Configuring Layer 2 Tunneling on a Port 8-11

Configuring Layer 2 Tunneling Per-VLAN 8-12

Monitoring and Verifying Tunneling Status 8-12

CHAPTER

9 Configuring Link Aggregation on the ML-Series Card 9-1

Understanding Link Aggregation 9-1

Configuring Link Aggregation 9-2

Configuring Fast EtherChannel 9-2

EtherChannel Configuration Example 9-3

Configuring POS Channel 9-4

POS Channel Configuration Example 9-5

Contents

v

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Understanding Encapsulation over FEC or POS Channel 9-6

Configuring Encapsulation over EtherChannel or POS Channel 9-6

Encapsulation over EtherChannel Example 9-7

Monitoring and Verifying EtherChannel and POS 9-8

Load Balancing on the ML-Series cards 9-9

CHAPTER

10 Configuring IRB on the ML-Series Card 10-1

Understanding Integrated Routing and Bridging 10-1

Configuring IRB 10-2

IRB Configuration Example 10-3

Monitoring and Verifying IRB 10-4

CHAPTER

11 Configuring Quality of Service on the ML-Series Card 11-1

Understanding QoS 11-2

Priority Mechanism in IP and Ethernet 11-2

IP Precedence and Differentiated Services Code Point 11-2

Ethernet CoS 11-3

ML-Series QoS 11-4

Classification 11-4

Policing 11-5

Marking and Discarding with a Policer 11-5

Queuing 11-6

Scheduling 11-6

Control Packets and L2 Tunneled Protocols 11-7

Egress Priority Marking 11-8

Ingress Priority Marking 11-8

QinQ Implementation 11-8

Flow Control Pause and QoS 11-9

QoS on RPR 11-9

Configuring QoS 11-10

Creating a Traffic Class 11-10

Creating a Traffic Policy 11-11

Attaching a Traffic Policy to an Interface 11-15

Configuring CoS-Based QoS 11-16

Monitoring and Verifying QoS Configuration 11-16

QoS Configuration Examples 11-17

Traffic Classes Defined Example 11-18

Traffic Policy Created Example 11-18

Contents

vi

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

class-map match-any and class-map match-all Commands Example 11-19

match spr1 Interface Example 11-19

ML-Series VoIP Example 11-20

ML-Series Policing Example 11-20

ML-Series CoS-Based QoS Example 11-21

Understanding Multicast QoS and Multicast Priority Queuing 11-23

Default Multicast QoS 11-23

Multicast Priority Queuing QoS Restrictions 11-24

Configuring Multicast Priority Queuing QoS 11-24

QoS not Configured on Egress 11-26

ML-Series Egress Bandwidth Example 11-26

Case 1: QoS with Priority and Bandwidth Configured Without Priority Multicast 11-26

Case 2: QoS with Priority and Bandwidth Configured with Priority Multicast 11-27

Understanding CoS-Based Packet Statistics 11-28

Configuring CoS-Based Packet Statistics 11-29

Understanding IP SLA 11-30

IP SLA on the ML-Series 11-31

IP SLA Restrictions on the ML-Series 11-31

CHAPTER

12 Configuring the Switching Database Manager on the ML-Series Card 12-1

Understanding the SDM 12-1

Understanding SDM Regions 12-1

Configuring SDM 12-2

Configuring SDM Regions 12-2

Configuring Access Control List Size in TCAM 12-3

Monitoring and Verifying SDM 12-3

CHAPTER

13 Configuring Access Control Lists on the ML-Series Card 13-1

Understanding ACLs 13-1

ML-Series ACL Support 13-1

IP ACLs 13-2

Named IP ACLs 13-2

User Guidelines 13-2

Creating IP ACLs 13-3

Creating Numbered Standard and Extended IP ACLs 13-3

Creating Named Standard IP ACLs 13-4

Creating Named Extended IP ACLs (Control Plane Only) 13-4

Applying the ACL to an Interface 13-4

Contents

vii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Modifying ACL TCAM Size 13-5

CHAPTER

14 Configuring Resilient Packet Ring on the ML-Series Card 14-1

Understanding RPR 14-1

Role of SONET Circuits 14-2

Packet Handling Operations 14-2

Ring Wrapping 14-3

RPR Framing Process 14-4

MAC Address and VLAN Support 14-6

RPR QoS 14-6

CTM and RPR 14-6

Configuring RPR 14-6

Connecting the ML-Series Cards with Point-to-Point STS Circuits 14-7

Configuring CTC Circuits for RPR 14-7

CTC Circuit Configuration Example for RPR 14-7

Configuring RPR Characteristics and the SPR Interface on the ML-Series Card 14-9

Assigning the ML-Series Card POS Ports to the SPR Interface 14-11

Creating the Bridge Group and Assigning the Ethernet and SPR Interfaces 14-13

RPR Cisco IOS Configuration Example 14-14

Verifying Ethernet Connectivity Between RPR Ethernet Access Ports 14-15

CRC Threshold Configuration and Detection 14-15

Monitoring and Verifying RPR 14-16

Add an ML-Series Card into an RPR 14-17

Adding an ML-Series Card into an RPR 14-19

Delete an ML-Series Card from an RPR 14-21

Deleting an ML-Series Card from an RPR 14-23

Cisco Proprietary RPR KeepAlive 14-25

Configuring Cisco Proprietary RPR KeepAlive 14-25

Monitoring Cisco Propretary RPR KeepAlive 14-25

Cisco Proprietary RPR Shortest Path 14-25

Configuring Shortest Path and Topology Discovery 14-25

Monitoring and Verifying Shortest Path andTopolgy Discovery 14-26

Redundant Interconnect 14-26

CHAPTER

15 Configuring Security for the ML-Series Card 15-1

Understanding Security 15-1

Disabling the Console Port on the ML-Series Card 15-2

Secure Login on the ML-Series Card 15-2

Contents

viii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Secure Shell on the ML-Series Card 15-2

Understanding SSH 15-2

Configuring SSH 15-3

Configuration Guidelines 15-3

Setting Up the ML-Series Card to Run SSH 15-3

Configuring the SSH Server 15-4

Displaying the SSH Configuration and Status 15-5

RADIUS on the ML-Series Card 15-6

RADIUS Relay Mode 15-6

Configuring RADIUS Relay Mode 15-7

RADIUS Stand Alone Mode 15-7

Understanding RADIUS 15-8

Configuring RADIUS 15-8

Default RADIUS Configuration 15-9

Identifying the RADIUS Server Host 15-9

Configuring AAA Login Authentication 15-11

Defining AAA Server Groups 15-13

Configuring RADIUS Authorization for User Privileged Access and Network Services 15-15

Starting RADIUS Accounting 15-16

Configuring a nas-ip-address in the RADIUS Packet 15-17

Configuring Settings for All RADIUS Servers 15-17

Configuring the ML-Series Card to Use Vendor-Specific RADIUS Attributes 15-18

Configuring the ML-Series Card for Vendor-Proprietary RADIUS Server Communication 15-19

Displaying the RADIUS Configuration 15-20

CHAPTER

16 Configuring Bridging on the ML-Series Card 16-1

Understanding Bridging 16-1

Configuring Bridging 16-2

Monitoring and Verifying Bridging 16-3

CHAPTER

17 CE-100T-8 Ethernet Operation 17-1

CE-100T-8 Overview 17-1

CE-100T-8 Ethernet Features 17-2

Autonegotiation, Flow Control, and Frame Buffering 17-2

Ethernet Link Integrity Support 17-3

Enhanced State Model for Ethernet and SONET Ports 17-4

IEEE 802.1Q CoS and IP ToS Queuing 17-4

RMON and SNMP Support 17-6

Statistics and Counters 17-6

Contents

ix

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

CE-100T-8 SONET Circuits and Features 17-6

Available Circuit Sizes and Combinations 17-6

CE-100T-8 STS/VT Allocation Tab 17-8

CE-100T-8 VCAT Characteristics 17-9

CE-100T-8 POS Encapsulation, Framing, and CRC 17-10

CE-100T-8 Loopback, J1 Path Trace, and SONET Alarms 17-11

APPENDIX

A Command Reference for the ML-Series Card A-1

APPENDIX

B Unsupported CLI Commands for the ML-Series Card B-1

Unsupported Privileged Exec Commands B-1

Unsupported Global Configuration Commands B-1

Unsupported POS Interface Configuration Commands B-3

Unsupported FastEthernet Interface Configuration Commands B-4

Unsupported Port-Channel Interface Configuration Commands B-5

Unsupported BVI Interface Configuration Commands B-6

APPENDIX

C Using Technical Support C-1

Gathering Information About Your Internetwork C-1

Getting the Data from Your ML-Series Card C-2

Providing Data to Your Technical Support Representative C-3

I

NDEX

Contents

x

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

FIGURES

i

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Figure 3-1 CTC Node View Showing IP Address 3-3

Figure 3-2 Console Cable Adapter 3-4

Figure 6-1 Spanning-Tree Topology 6-5

Figure 6-2 Spanning-Tree Interface States 6-6

Figure 6-3 Spanning Tree and Redundant Connectivity 6-8

Figure 6-4 Proposal and Agreement Handshaking for Rapid Convergence 6-12

Figure 6-5 Sequence of Events During Rapid Convergence 6-13

Figure 7-1 VLANs Spanning Devices in a Network 7-2

Figure 7-2 Bridging IEEE 802.1Q VLANs 7-4

Figure 8-1 IEEE 802.1Q Tunnel Ports in a Service-Provider Network 8-2

Figure 8-2 Normal, IEEE 802.1Q, and IEEE 802.1Q-Tunneled Ethernet Packet Formats 8-3

Figure 8-3 ERMS Example 8-7

Figure 9-1 Encapsulation over EtherChannel Example 9-3

Figure 9-2 POS Channel Example 9-5

Figure 9-3 Encapsulation over EtherChannel Example 9-7

Figure 10-1 Configuring IRB 10-3

Figure 11-1 IP Precedence and DSCP 11-3

Figure 11-2 Ethernet Frame and the CoS Bit (IEEE 802.1p) 11-3

Figure 11-3 ML-Series QoS Flow 11-4

Figure 11-4 Dual Leaky Bucket Policer Model 11-5

Figure 11-5 Queuing and Scheduling Model 11-7

Figure 11-6 QinQ Implementation on the ML-Series Card 11-9

Figure 11-7 ML-Series VoIP Example 11-20

Figure 11-8 ML-Series Policing Example 11-21

Figure 11-9 ML-Series CoS Example 11-22

Figure 11-10 QoS not Configured on Egress 11-26

Figure 14-1 RPR Packet Handling Operations 14-3

Figure 14-2 RPR Ring Wrapping 14-4

Figure 14-3 RPR Frame for ML-Series Card 14-5

Figure 14-4 RPR Frame Fields 14-5

Figures

ii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Figure 14-5 Three-Node RPR Example 14-8

Figure 14-6 RPR Bridge Group 14-13

Figure 14-7 Two-Node RPR Before the Addition 14-17

Figure 14-8 Three-Node RPR After the Addition 14-18

Figure 14-9 Three-Node RPR Before the Deletion 14-22

Figure 14-10 Two-Node RPR After the Deletion 14-22

Figure 16-1 Bridging Example 16-3

Figure 17-1 CE-100T-8 Point-to-Point Circuit 17-1

Figure 17-2 Flow Control 17-3

Figure 17-3 End-to-End Ethernet Link Integrity Support 17-3

Figure 17-4 CE-100T-8 STS/VT Allocation Tab 17-9

Figure 17-5 ONS CE-100T-8 Encapsulation and Framing Options 17-11

TABLES

i

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Table 2-1 ML-Series POS Statistics Fields and Buttons 2-1

Table 2-2 ML-Series Ethernet Statistics Fields and Buttons 2-2

Table 3-1 RJ-11 to RJ-45 Pin Mapping 3-4

Table 3-2 Cisco IOS Command Modes 3-10

Table 5-1 ML-Series Card Supported Circuit Sizes and Sizes Required for Ethernet Wire Speeds 5-2

Table 5-2 ML-Series Card Encapsulation, Framing, and CRC Sizes 5-3

Table 6-1 Switch Priority Value and Extended System ID 6-4

Table 6-2 Spanning-Tree Timers 6-4

Table 6-3 Port State Comparison 6-10

Table 6-4 RSTP BPDU Flags 6-13

Table 6-5 Default STP and RSTP Configuration 6-16

Table 6-6 Commands for Displaying Spanning-Tree Status 6-21

Table 8-1 VLAN-Transparent Service Versus VLAN-Specific Services 8-6

Table 8-2 Default Layer 2 Protocol Tunneling Configuration 8-10

Table 8-3 Commands for Monitoring and Maintaining Tunneling 8-12

Table 9-1 MAC Based- 2- Port Channel Interface 9-9

Table 9-2 IP Based- 2- Port Channel Interface 9-10

Table 9-3 MAC Based - 4-Port Channel Interface 9-10

Table 9-4 IP Based - 4-Port Channel Interface 9-11

Table 10-1 Commands for Monitoring and Verifying IRB 10-5

Table 10-2 show interfaces irb Field Descriptions 10-6

Table 11-1 Traffic Class Commands 11-11

Table 11-2 Traffic Policy Commands 11-12

Table 11-3 CoS Commit Command 11-16

Table 11-4 Commands for QoS Status 11-16

Table 11-5 CoS Multicast Priority Queuing Command 11-25

Table 11-6 Packet Statistics on ML-Series Card Interfaces 11-28

Table 11-7 CoS-Based Packet Statistics Command 11-29

Table 11-8 Commands for CoS-Based Packet Statistics 11-29

Table 12-1 Default Partitioning by Application Region 12-2

Tables

ii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Table 12-2 Partitioning the TCAM Size for ACLs 12-3

Table 13-1 Commands for Numbered Standard and Extended IP ACLs 13-3

Table 13-2 Applying ACL to Interface 13-5

Table 14-1 Definitions of RPR Frame Fields 14-5

Table 15-1 Commands for Displaying the SSH Server Configuration and Status 15-5

Table 17-1 IP ToS Priority Queue Mappings 17-5

Table 17-2 CoS Priority Queue Mappings 17-5

Table 17-3 CE-100T-8 Supported Circuit Sizes 17-7

Table 17-4 SONET Circuit Size Required for Ethernet Wire Speeds 17-7

Table 17-5 CCAT High Order Circuit Size Combinations 17-7

Table 17-6 VCAT High Order Circuit Size Combinations 17-7

Table 17-7 CE-100T-8 Maximum Service Densities 17-8

i

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Preface

Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms

do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration.

Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's

path protection feature, which may be used in any topological network configuration. Cisco does not

recommend using its path protection feature in any particular topological network configuration.

This section provides the following information:

• Document Objectives, page ii

• Audience, page ii

• Related Documentation, page ii

• Document Conventions, page iii

• Obtaining Optical Networking Information, page ix

• Obtaining Documentation, Obtaining Support, and Security Guidelines, page ix

Revision History

Date Notes

July 2008 Modified a statement in the “Flow Control Pause and QoS” section of Chapter 12,

Configuring Quality of Service.

September 2008 Updated the section “CE-100T-8 VCAT Characteristics” in Chapter 17,

CE-100T-8 Ethernet Operation.

December 2008 Added a new section “Load Balancing on the ML-Series Cards” in Chapter 9,

Configuring Link Aggregation on the ML-Series Cards”.

ii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Preface

Document Objectives

This guide covers the software features and operations of the ML-100T-8 and the CE-100T-8 Ethernet

cards for the Cisco ONS 15310-CL and the Cisco ONS 15310-MA. It explains software features and

configuration for Cisco IOS on the ML-Series card. It also explains software feature and configuration

for Cisco Transport Controller (CTC) on the CE-100T-8 card. The CE-100T-8 card is also available as a

card for the Cisco ONS 15454 and Cisco ONS 15454 SDH. This version of the card is described in the

Cisco ONS 15454 and Cisco ONS 15454 SDH Ethernet Card Software Feature and Configuration Guide.

Use this guide in conjunction with the appropriate publications listed in the Related Documentation

section.

Audience

To use the ML-Series card chapters of this publication, you should be familiar with Cisco IOS and

preferably have technical networking background and experience. To use the CE-100T-8 card chapter of

this publication, you should be familiar with CTC and preferably have technical networking background

and experience.

Related Documentation

Use the Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and

Configuration Guide R8.5 in conjunction with the following general ONS 15310-CL and ONS

15310-MA system publications:

• To install, turn up, provision, and maintain a Cisco ONS 15310-CL or Cisco ONS 15310-MA node

and network, refer to the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.

• For alarm clearing, general troubleshooting procedures, transient conditions, and error messages for

a Cisco ONS 15310-CL and Cisco ONS 15310-MA card, node, or network, refer to the

Cisco ONS 15310-CL and Cisco ONS 15310-MA Troubleshooting Guide.

January 2009 Added the following sections in Chapter 11, Configuring Quality of Service on

the ML-Series Card:

• QoS not Configured on Egress

• ML-Series Egress Bandwidth Example

• Added a new bullet point in the “IP SLA Restrcitions on the ML-Series”

section.

• Added Tables 9-1 and 9-2 and updated Table 4 in the “Load Balancing on

ML-Series Cards” section of Chapter 9, Configuring Link Aggregation on the

ML-Series Cards.

February 2009 Added a note in the “Ring Wrapping” section of Chapter 15, Configuring

Resilient Packet Ring on the ML-Series Card.

June 2009 Updated the sections “RMON” and “SNMP” in Chapter 1, Overview of the

ML-Series Cards.

Date Notes

iii

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Preface

• For detailed reference information about Cisco ONS 15310-CL or Cisco ONS 15310-MA cards,

nodes, and networks, refer to the Cisco ONS 15310-CL and Cisco ONS 15310-MA Reference

Manual.

The ML-Series card employs the Cisco IOS Modular QoS CLI (MQC). For more information on general

MQC configuration, refer to the following Cisco IOS documents:

• Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.2

• Cisco IOS Quality of Service Solutions Command Reference, Release 12.2

• The ML-Series card employs Cisco IOS 12.2. For more general information on Cisco IOS 12.2, refer

to the extensive Cisco IOS documentation at http://www.cisco.com.

For an update on End-of-Life and End-of-Sale notices, refer to

http://cisco.com/en/US/products/hw/optical/ps2001/prod_eol_notices_list.html.

Document Conventions

This publication uses the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the

document.

Caution Means reader be careful. In this situation, the user might do something that could result in equipment

damage or loss of data.

Convention Application

boldface Commands and keywords in body text.

italic Command input that is supplied by the user.

[ ] Keywords or arguments that appear within square brackets are optional.

{ x | x | x } A choice of keywords (represented by x) appears in braces separated by

vertical bars. The user must select one.

Ctrl The control key. For example, where Ctrl + D is written, hold down the

Control key while pressing the D key.

screen font

Examples of information displayed on the screen.

boldface screen font

Examples of information that the user must enter.

< > Command parameters that must be replaced by module-specific codes.

iv

Cisco ONS 15310-CL and Cisco ONS 15310-MA Ethernet Card Software Feature and Configuration Guide R8.5

78-18133-01

Preface

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen

führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen

und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Page is loading ...

Cisco Systems 15310-CL User manual

This manual is also suitable for

Cisco Systems 15310-CL User manual

Related papers

Other documents