Kohler Hot Tub K-1418-CT User manual

Brand: Kohler

Model: Hot Tub K-1418-CT

Type: User manual

This manual is also suitable for

K-1418-CT

Homeowners Guide

Bath Whirlpool

M product numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de M corresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-1418-CT

1023246-5-C

Important Information

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRICAL SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this

unit unless they are closely supervised at all times.

WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the

whirlpool.

WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,

telephone, radio, or television) within 5’ (1.5 m) of this whirlpool.

WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal

hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs

when the internal temperature of the body reaches a level several degrees above the normal body

temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal

temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia

include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c)

unawareness of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to

exit the bath, and (f) unconsciousness resulting in the danger of drowning.

WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical

history should consult a physician before using a whirlpool equipped with a heater.

WARNING: Risk of scalding. Do not allow the water temperature in the whirlpool to exceed 104°F

(40°C).

The heater will automatically maintain the water temperature when the whirlpool is running, as long as the

water temperature does not exceed 104°F (40°C). The heater will disengage at higher temperatures.

An equipment grounding terminal is provided in the ﬁeld wiring compartment. To reduce the risk of electric

shock, this terminal must be connected to the grounding means provided in the electric supply panel with a

conductor equivalent in size to the circuit conductors supplying this whirlpool.

A pressure wire connector is provided on the exterior of the pump or control within this unit to permit

connection of a bonding conductor between this unit and all other exposed metal in the vicinity, as needed to

comply with local requirements.

Use this whirlpool only for its intended purpose as described in this guide. Do not use attachments not

recommended by the manufacturer.

Never drop or insert any object into any opening. Keep small objects such as bath toys and bathing

accessories out of the whirlpool while the unit is running.

Do not operate this unit without the guard (cover) over the suction ﬁtting.

The whirlpool must be connected only to a supply circuit that is protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Residual Current Device (RCD). Such a GFCI or RCD should be provided by

the installer and should be tested on a routine basis. To test the GFCI or RCD, press the test button. The

GFCI or RCD should interrupt power. Press the reset button. Power should be restored. If the GFCI or RCD

fails to operate in this manner, the GFCI or RCD is defective. If the GFCI or RCD interrupts power to the

bath without the test button being pressed, a ground current is ﬂowing, indicating the possibility of an

1023246-5-C 2 Kohler Co.

Important Information (cont.)

electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the problem corrected by a

qualiﬁed service representative before using.

Flush your whirlpool system twice a month or more depending upon usage, as described in the ″Flush

System″ section of this guide.

Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use

heavy, vegetable-based shampoos or bath oils.

Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath

oil to foam excessively. For this reason, please don’t use these products during whirlpool operation.

FCC Compliance

FCC ID : N82-KOHLER001

Canada ID : 4554A-KOHLER001

Compliance Statement (Part 15.19)

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

Warning (Part 15.21)

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

users’ authority to operate the equipment.

Table of Contents

Important Information .............................................................. 2

FCC Compliance ................................................................. 3

Thank You For Choosing Kohler Company .............................................. 3

Your Kohler Whirlpool ............................................................. 4

Lighted User Keypad .............................................................. 5

Operation ...................................................................... 5

Remote Control .................................................................. 7

Care and Cleaning ................................................................ 8

Flush System .................................................................... 8

Warranty ....................................................................... 8

Troubleshooting ................................................................. 10

Service Parts ................................................................... 13

Thank You For Choosing Kohler Company

Thank you for choosing Kohler Co. Your Kohler Co. product reﬂects the true passion for design,

craftsmanship, artistry, and innovation Kohler Co. stands for. We are conﬁdent its dependability and beauty

will surpass your highest expectations, satisfying you for years to come.

All information in this guide is based upon the latest product information available at the time of

publication. At Kohler Co. we strive to fulﬁll our mission of improving the level of gracious living for each

person who is touched by our products and services. We reserve the right to make changes in product

characteristics, packaging, or availability at any time without notice.

Please take a few minutes to review this guide. Pay special attention to the care and cleaning instructions.

Kohler Co. 3 1023246-5-C

Your Kohler Whirlpool

Your new whirlpool is designed to stimulate, invigorate, and energize your body with comforting

hydro-massage therapy. The whirlpool consists of the following components:

Lighted User Keypad - Located within easy reach, allows you to turn the whirlpool on and off. It

also allows you to access all the whirlpool modes and regulate the water ﬂow or pulse speed.

Remote Control - Places the whirlpool functions at your ﬁngertips to further enhance your bathing

experience. The functions of the remote control are identical to the lighted user keypad.

Pump Motor - Provides quiet, variable speed power to circulate the water.

Heater - Automatically helps maintain a 104°F (40°C) water temperature, turns on when the

whirlpool is operating, and turns off when the pump motor is turned off. Using the lighted user

keypad, the heater may be turned off at any time while the pump is operating.

Effervescence - Eight effervescent ports emit thousands of champagne-like bubbles which provides a

relaxing, soothing experience.

Chromatherapy - Promotes relaxation and delivers a full spectrum of color. Chromatherapy may be

used with all modes of operation, even when the pump is not operating.

1023246-5-C 4 Kohler Co.

Lighted User Keypad

Available modes will be illuminated in blue. Active modes will be illuminated in green.

Power Turns the whirlpool pump on and off. Icons illuminated in blue indicate available

modes/features. Modes which are operating will be illuminated in green.

Outer Ring Rotate the outer ring to the desired mode. The selected mode will ﬂash blue.

OK Activates the desired mode.

Up Arrow Increases the water ﬂow when the Flexjet ﬂow mode is active.

Indicator Bar Displays the water ﬂow volume in the Flexjet ﬂow mode.

Effervescence

Mode

Ports activate to provide a gentle, soothing bubbling action.

Down Arrow Decreases the water ﬂow when the Flexjet ﬂow mode is active.

Chromatherapy

Cycle

Chromatherapy lights will automatically and continuously cycle through the eight colors:

white, violet, indigo blue, aqua blue, green, yellow, orange, and red. One cycle through all

eight colors takes approximately one minute.

Heater Automatically engages when the power icon is selected. Rotate the outer ring until the

heater mode is ﬂashing, then press OK to turn the heater off. Press OK again to turn the

heater back on.

Chromatherapy -

Speciﬁc Color

Press OK to activate, then use the up or down arrow to reach the desired color. Press OK

while the chromatherapy cycle is active to turn off the chromatherapy lights.

Operation

NOTE: If the whirlpool is not operating properly, consult the ″Troubleshooting″ section of this guide

before calling a qualiﬁed service representative.

Whirlpool

NOTICE: Do not allow the water temperature in the whirlpool to exceed 104°F (40°C). The heater will

automatically maintain the water temperature when the whirlpool is running, as long as the water

temperature does not exceed 104°F (40°C). The heater will disengage at higher temperatures.

Close the drain, then ﬁll the whirlpool to a level at least 2″ (5.1 cm) above the highest effervescent

port. Using your hand, test the water temperature for comfort and safety. Carefully enter the bath.

Press the power icon to turn on the whirlpool pump and heater. Water will ﬂow at medium volume.

Press the up or down arrow icons to increase or decrease the water ﬂow. The indicator bar will

display the water ﬂow volume.

If desired, turn the heater off by pressing the heater icon. Press the button a second time to turn the

heater back on.

Chromatherapy Cycle

Heater On/Off

Decreases Flow or Pulse

Effervescence Mode

Increases Flow or Pulse

Rotate outer ring to

access desired mode.

Power On/Off

Chromatherapy - Specific Color

Activates Mode Selected

Indicator Bar

Kohler Co. 5 1023246-5-C

Operation (cont.)

Press the power icon a second time to turn off the whirlpool pump and heater.

NOTE: The pump and heater will automatically stop after approximately 20 minutes of continuous

operation. If desired, press the power icon to reactivate the pump and heater.

Carefully exit the bath, then open the drain to empty the whirlpool.

Effervescence

Rotate the outer ring until the effervescence icon is ﬂashing, then press OK to activate the

effervescence ports. The water ﬂow volume will remain as previously set. Press OK while the

effervescence mode is ﬂashing to turn off the effervescence ports.

Chromatherapy

NOTE: The chromatherapy modes may be used with all modes of operation, even when the pump is not

operating.

Rotate the outer ring to select the chromatherapy mode, then press OK to activate the

chromatherapy lights. Press OK while the chromatherapy mode is active to turn off the

chromatherapy lights.

Rotate the outer ring to select chromatherapy speciﬁc color selection, then press OK. Use the up or

down arrow to reach the desired color. Press OK while the chromatherapy speciﬁc color selection is

active to turn off the chromatherapy lights.

1023246-5-C 6 Kohler Co.

Remote Control

Operate

The remote control, which functions are identical to the user keypad, places the whirlpool functions at

your ﬁngertips to further enhance your bathing experience. The remote control is waterproof, so it may be

used in the bath and will ﬂoat in the water.

Power Turn the whirlpool or heater on and off.

Mode Selector Functions in the same way as the outer ring on the user keypad. When pressed, one of the

modes will ﬂash on the user keypad. When pressed again, the next mode in clockwise

order will ﬂash. When the desired mode is ﬂashing, press ″OK″ to activate it.

OK Activates the desired mode.

Up Arrow Increases the water ﬂow or pulse.

Down Arrow Decreases the water ﬂow or pulse.

Program

NOTE: Programming of the remote control is normally not required. However, programming the remote

control to the user keypad may be necessary if: (1) more than one device in or near the vicinity of your

home uses a remote control or (2) you replace your remote control or pump control.

Turn the whirlpool power on.

Turn off all modes of operation. Wait approximately one minute until the keypad darkens

completely (sleep mode).

On the user keypad, press the up arrow, down arrow, and the ″OK″ button simultaneously. The

bottom LED on the user keypad indicator bar will begin ﬂashing.

While the bottom LED is ﬂashing, press the ″OK″ button on the user keypad. A light sequence will

illuminate up and down the indicator bar.

While the light sequence is active, press any button on the remote control. The program will

download and the user keypad will darken. The user keypad will now respond only to this remote

control.

Batteries

Unscrew the end cap of the remote control, as shown.

Insert two AAA batteries.

Securely tighten the end cap, making sure the end cap contacts the seal.

Activates Mode

Selected

Power

Increases Flow

or Pulse

Mode Selector

Decreases Flow

or Pulse

Kohler Co. 7 1023246-5-C

Care and Cleaning

For best results, keep the following in mind when caring for your KOHLER product:

•

Always test your cleaning solution on an inconspicuous area before applying to the entire surface.

•

Wipe surfaces clean and rinse completely with water immediately after applying cleaner. Rinse and

dry any overspray that lands on nearby surfaces.

•

Do not allow cleaners to soak on surfaces.

•

Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring

pad to clean surfaces.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &

Cleaning information, call 1-800-456-4537.

Flush System

NOTE: Flush your whirlpool system twice a month or more, depending upon usage.

Turn the jet trim rings fully clockwise to remove air induction.

Fill the whirlpool with warm water to a level at least 2″ (5.1 cm) above the highest jets, or leave

water in the whirlpool after using.

Add 2 teaspoons (10 ml) of a low-foaming, powder automatic dishwasher detergent and 20 ounces

(590 ml) of household bleach (5% - 6% sodium hypochlorite) to the water.

Run the whirlpool for 5 to 10 minutes. Turn off the whirlpool and drain.

If desired, rinse the bath surfaces with water.

Rinse the surfaces of the jets, faucet, handrails, and drain, and wipe them dry with a soft cloth.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year

from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection

discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not

responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home

Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI

53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and

001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS

WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on

how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential

damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal

rights. You may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

Warranty

KOHLER CO.

It is recommended that at the time of purchase, you verify that all accessories and components are complete

in this package.

1023246-5-C 8 Kohler Co.

Warranty (cont.)

This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the

date of purchase as shown on the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its authorized distributors.

2. To obtain warranty service, please present the invoice and corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new

replacement or an equivalent model (in those cases that the model has been discontinued) when the product

is beyond repair, without any charge to the consumer.

4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.

5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may

substitute the warranty in the case that there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS

The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the instructions concerning use and operation set

forth in the owner’s manual or installation instructions, and when the recommendations and warnings

included are not observed.

2. When the product has been modiﬁed or dismantled partially or totally; or has been used in a negligent

fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not

authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster such as ﬁre or acts of God, including

ﬂooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can

exercise your rights under this warranty, please call 001-800-456-4537.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V.

AV. CARLOS PACHECO NO. 7200

CHIHUAHUA, CHIH., MEXICO C.P. 31060

TEL: 52 (14) 29-11-11

Kohler Co. 9 1023246-5-C

Troubleshooting

NOTICE: This section is for general aid only. A Kohler Authorized Service Representative or qualiﬁed

electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale

distributor.

Remove the Port

Insert the ﬂange removal tool (provided) into the opening of the port.

Place your thumb against the whirlpool wall while ﬁrmly grasping the ﬂange removal tool.

Pull the ﬂange removal tool until the ﬂange pulls free from the housing.

Reinstall the Port

NOTE: Do not use force when reinstalling the port.

Carefully insert the ﬂange into the housing, then lightly push and rotate the ﬂange until it snaps

into position.

Verify the port is installed correctly. Remove and reinstall, if necessary.

Troubleshooting Table

User Keypad and Pump

Symptoms Probable Causes Recommended Action

1. User keypad does not

illuminate when power

button is pressed or outer

ring is rotated.

A. No power to control. A. Check wiring and connect power.

B. GFCI or RCD tripped. B. Reset GFCI or RCD.

C. Wiring harness from user

keypad to control is loose,

disconnected or damaged.

C. Check wiring for proper

connections. Replace wiring

harness if necessary.

D. User keypad does not work. D. Replace user keypad.

E. Control does not work. E. Replace control.

2. User keypad is

illuminated, but does not

respond to buttons or

outer ring.

A. Control program is locked. A. Reset GFCI or RCD.

B. Wiring harness from user

keypad to control is loose,

disconnected or damaged.

B. Check wiring for proper

connections. Replace wiring

harness if necessary.

C. User keypad does not work. C. Replace user keypad.

D. Control does not work. D. Replace control.

Flange Removal Tool

Flange

Housing

Whirlpool

1023246-5-C 10 Kohler Co.

Troubleshooting (cont.)

User Keypad and Pump

Symptoms Probable Causes Recommended Action

3. User keypad indicator bar

keeps scanning at

power-up.

A. Control program is locked. A. Reset GFCI or RCD.

B. Wiring harness from user

keypad to control is loose,

disconnected or damaged.

B. Check wiring for proper

connections. Replace wiring

harness if necessary.

C. User keypad does not work. C. Replace user keypad.

D. Control does not work. D. Replace control.

4. User keypad is

illuminated, but pump

will not start.

A. Power cord from pump to

control is loose, disconnected or

damaged.

A. Check wiring for proper

connections.

B. Pump does not work. B. Replace pump.

C. Control does not work. C. Replace control.

5. Motor runs but pump will

not prime (cavitates).

A. Pump is shimmed too high. A. Lower pump/control to subﬂoor

level.

B. Small air leak at pump inlet. B. Securely tighten nut(s) on intake

side of pump.

C. Motor/pump does not work. C. Replace motor/pump.

D. Control does not work. D. Replace control.

6. Pump stops before 18

minutes.

A. GFCI or RCD tripped. A. Identify source of fault, and correct.

Reset GFCI or RCD.

B. Suction is blocked. B. Remove obstruction.

C. Jets are blocked. C. Remove blockage.

D. Motor overheated and

protection device activated.

D. Check for blockage at suction

and/or jets. Remove blockage and

allow motor to cool.

7. Pump does not

automatically stop after 22

minutes.

A. 20-minute timer inadvertently

disabled.

A. See service manual.

8. Pump will not turn off

when the power button

on user keypad is

pressed.

A. User keypad does not work. A. Replace user keypad.

B. Control does not work. B. Replace control.

9. Pump operates but

variable speed feature

does not work.

A. Motor/pump does not work. A. Replace motor/pump.

B. Control does not work. B. Replace control.

10. Bath water cools while

pump is operating.

A. Water temperature above 104°F

(40°C).

A. Allow bath water to cool.

B. Heater is turned off on user

keypad.

B. Turn heater on.

C. Wiring from heater to control is

loose, disconnected or damaged.

C. Check wiring for proper

connections.

D. Heater does not work. D. Replace heater.

E. Control does not work. E. Replace control.

11. Noisy operation. A. Pump banding straps have not

been cut.

A. Cut pump banding straps with tin

snips.

B. Dry or dislodged jet O-ring

(squeal).

B. Remove jet, replace and lubricate

O-ring, and reinstall jet.

Kohler Co. 11 1023246-5-C

Troubleshooting (cont.)

Effervescent Ports

Symptoms Probable Causes Recommended Action

1. Effervescent ports do not

work.

A. Whirlpool pump is not

operating.

A. Turn on pump.

B. Butterﬂy valve does not work. B. Replace butterﬂy valve.

C. Pump does not work. C. Refer to the service manual to

troubleshoot the system. Refer to

installer/dealer.

D. Control does not work. D. Replace control.

2. Effervescent ports do not

bubble.

A. Air intake on suction line is

blocked.

A. Remove blockage.

B. Water ﬂow is too low. B. Increase water ﬂow.

Chromatherapy Lights

Symptoms Probable Causes Recommended Action

1. Chromatherapy lights do

not work.

A. Loose, disconnected or damaged

wiring/connections.

A. Check wiring for proper

connections. Replace wiring if

necessary.

B. Control does not work. B. Replace control.

Remote Control

Symptoms Probable Causes Recommended Action

1. Remote control does not

work.

A. Batteries improperly installed or

dead.

A. Replace batteries.

B. Antenna on wiring harness is

damaged.

B. Replace wiring harness.

C. Remote control not programmed

correctly.

C. See homeowners guide or service

manual.

D. Remote control does not work. D. Replace remote control.

E. Control does not work. E. Replace control.

1023246-5-C 12 Kohler Co.

Service Parts

93685

Housing

96708

Flange

96895** (Colored Finishes)

65061** (Metal Finishes)

Cover

65886 (Acrylic and FRP)

60050 (Cast Iron)

Gasket

65054**

Screw

65226**

Suction Cover Plug

73518

Plug

1003065

Suction Flange

Removal Tool

**Finish/color code must be specified when ordering

93552**

Flange Cap

96744

Flange Removal Tool

1010618

Elbow

93315

Gasket

1035480**

Flange

1001878

Effervescence Ports

Housing

1012821

Light Housing

93841

Screw

1019933

Chromatherapy Lights

93836 (1/2")

93837 (3/4")

93838 (1")

93839 (1-1/4")

94853 (1-1/2")

Tube (w/Couplings)

91967

Check Valve

1015017

Plug/Wire

Assembly

1015008

Wire Harness

1023292

Cap

Kohler Co. 13 1023246-5-C

1016953

Pump

1016954

Motor

1010548

Volute

1010673

Seal

1010677

Screw

1010675

O-Ring

1013755

Impeller

1010676

Cover

94821

O-Ring

61845-K

Copper Grounding Wire

1019719

Connector

1012855

Nut

1019447-A [1/4" (6 mm)]

1019447-B [1/2" (1.3 cm)]

1019447-C [3/4" (1.9 cm)]

Isolation Mount

1018964

Bracket

1019433

Carriage Bolt

1001794

Locknut

90153

Locknut

1019446-A [1-3/4" (4.4 cm)]

1019446-B [2-3/4" (7 cm)]

1019446-C [3" (7.6 cm)]

1019446-D [2-1/2" (6.4 cm)]

1019446-E [2" (5.1 cm)]

1019446-F [2-1/4" (5.7 cm)]

1019446-G [3-1/4" (8.3 cm)]

1019446-H [3-1/2" (8.9 cm)]

1019446-J [3-3/4" (9.5 cm)]

1019446-K [4" (10.2 cm)]

1019446-L [1-1/2" (3.8 cm)]

1019446-M [1-1/4" (3.2 cm)]

Stud

1019444-A [3/4" (1.9 cm)]

1019444-B [1-3/4" (4.4 cm)]

1019444-C [2" (5.1 cm)]

1019444-D [1-1/2" (3.8 cm)]

1019444-E [1" (2.5 cm)]

1019444-F [1-1/4" (3.2 cm)]

1019444-G [2-1/4" (5.7 cm)]

1019444-H [2-1/2" (6.4 cm)]

1019444-J [2-3/4" (7 cm)]

1019444-K [3" (7.6 cm)]

1019444-L [1/2" (1.3 cm)]

1019444-M [1/4" (6 mm)]

Spacer

Outlet

To Tee Heater

60320

Screw

93892-A

Electrical Box

67065

Ground Lug

61776

Lock Washer

1033678

Screw

93003

Strain Relief

94821

O-Ring

93893

Cover

60320

Screw

67065

61776

Lock Washer

1080775

Pump Tee

To In-line Heater

94821

O-Ring

1080774

Union Assy

Ground Lug

Control

1018660

1018662

**Finish/color code must be specified when ordering.

(One Outlet)

(Two Outlets)

1023246-5-C 14 Kohler Co.

1018710

Tee Heater

94821

O-Ring

94821

O-Ring

1012977

Adapter

1012916

Nut with Screws

1011679

Gasket

1012977

Adapter

1011679

Gasket

**Finish/color code must be specified when ordering.

94821

O-Ring

1012653

Adapter

1012653

Adapter

1012916

Nut w/Screws

1022408

In-line Heater

94821

O-Ring

1032545

Housing

Kohler Co. 15 1023246-5-C

65157

Nut

1020677

Gasket

1013499

Housing

1013453

Spring

91639

O-Ring

1013452**

Dial Trim

1013497-A

Decal

1013497-B

Decal

1013497-C

Decal

1013497-D

Decal

1013497-E

Decal

1020678-A

1023381

Wrench

1020678-B

1020678-D

1020678-C

1020678-E

**Finish/color code must be specified when ordering.

Cover/Circuit Board

(w/Wrench)

1013497-M

Decal

1020678-M

Cover/Circuit Board

(w/Wrench)

1013497-N

Decal

1020678-N

Cover/Circuit Board

(w/Wrench)

1013497-P

Decal

1020678-P

Cover/Circuit Board

(w/Wrench)

Cover/Circuit Board

(w/Wrench)

Cover/Circuit Board

(w/Wrench)

Cover/Circuit Board

(w/Wrench)

Cover/Circuit Board

(w/Wrench)

Carefully study decal and cover

detail below for proper service

part identification.

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

O-Ring

91639

O-Ring

1023246-5-C 16 Kohler Co.

1023091**

Cap

1013471**

Stand

1013464-A

Decal

1013464-B

Decal

1022253-B**

Remote

1022253-A**

Remote

1013822-A**

Remote w/Stand

1013822-B**

Remote w/Stand

1023091**

Cap

1013471**

Stand

**Finish/color code must be specified when ordering.

Kohler Co. 17 1023246-5-C

Guide du propriétaire

Baignoire à hydromassage

Renseignements importants

CONSIGNES RELATIVES AUX RISQUES

D’INCENDIE, D’ÉLECTROCUTION OU DE

BLESSURES CORPORELLES

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS

CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : Lors de l’utilisation des produits électriques, des précautions de base

doivent toujours être observées, incluant ce qui suit :

DANGER : Risque de blessures corporelles. Aﬁn de réduire les risques de blessures, ne jamais

permettre à un enfant d’utiliser cet appareil sans surveillance.

AVERTISSEMENT : Risque de blessures corporelles. Pour éviter les blessures corporelles, entrer

et sortir avec précaution de la baignoire à hydromassage.

AVERTISSEMENT : Risque d’électrocution. Ne pas raccorder d’appareils électriques (tels que

sèche-cheveux, lampe, téléphone, radio ou télévisions) dans les 5’ (1,5 m) de cette baignoire à

hydromassage.

AVERTISSEMENT : La consommation d’alcool, de drogues ou de médicaments peuvent

augmenter considérablement le risque fatal d’hyperthermie. Une immersion prolongée dans l’eau

chaude peut provoquer l’hyperthermie. L’hyperthermie a lieu lorsque la température corporelle

interne atteint plusieurs degrés au dessus de la température normale de 98,6°F (37°C). Les

symptômes d’hyperthermie comprennent la hausse de la température corporelle, l’étourdissement,

la léthargie, la somnolence et l’évanouissement. Les effets de l’hyperthermie comprennent: (a)

défaut de percevoir la chaleur, (b) défaut de s’apercevoir du besoin de sortir de la baignoire, (c)

incapacité de reconnaître le danger, (d) dommages au foetus dans le cas des femmes enceintes, (e)

incapacité physique de sortir de la baignoire et (f) inconscience et danger conséquent de noyade.

AVERTISSEMENT : Risque d’hyperthermie. Les personnes sous médicaments ou qui sont en

observation médicale doivent consulter leur médecin avant d’utiliser des baignoires à hydromassage

équipées de chauffe-eau.

AVERTISSEMENT : Risque de brûlures. Ne pas laisser la température de la baignoire à

hydromassage excéder 104° F (40°C).

Un chauffe-eau maintient automatiquement la température d’eau quand la baignoire à hydromassage est en

marche, et tant que la température d’eau ne dépasse pas 104°F (40°C). Le chauffe-eau s’arrêtera aux

températures plus hautes.

Une borne de mise à la terre est incluse dans le boîtier du câblage. Aﬁn de réduire les risques

d’électrocution, ce terminal doit être raccordé à la borne de mise à la terre du panneau du service électrique,

avec un câble ayant le même calibre que celui du circuit de contrôle qui alimente cet équipement.

Un connecteur à pression par câble est prévu à l’extérieur de la pompe ou de la commande de cet appareil

aﬁn de permettre la connexion entre l’appareil et toutes autres surfaces de métal avoisinantes, tel que requis

par les normes locales.

Kohler Co. Français-1 1023246-5-C

Renseignements importants (cont.)

Utiliser cette baignoire à hydromassage uniquement pour un usage tel que décrit dans ce guide. Ne pas

utiliser des ﬁxations non recommandées par le fabricant.

Ne jamais faire tomber ou insérer d’objet quelconque dans les ouvertures. Ne pas laisser de petits objets tels

que des jouets ou accessoires pour le bain dans la baignoire à hydromassage lorsqu’elle est en marche.

Ne pas utiliser cet appareil sans ses protecteurs (couvercles) sur ses raccords d’aspiration.

La baignoire à hydromassage doit être raccordée uniquement à une prise de terre, protégée par un

disjoncteur différentiel (GFCI) ou un appareil de courant résiduel (RCD). De tels disjoncteurs GFCI ou RCD

devraient être fournis par l’installateur et vériﬁés régulièrement. Appuyer sur le bouton de test pour tester

les disjoncteurs GFCI ou RCD. Le GFCI ou RCD devraient couper le courant. Appuyer sur le bouton de

ré-initialisation. L’alimentation devrait être restituée. Si les disjoncteurs GFCI or RCD ne fonctionnent pas de

cette façon, l’un ou l’autre est défectueux. Si les disjoncteurs GFCI ou RCD stoppent l’alimentation électrique

à la baignoire sans que le bouton test ne soit utilisé, il y a donc un court circuit indiquant la possibilité de

choc électrique. Ne pas utiliser pas cette baignoire à hydromassage. Débrancher la baignoire à hydromassage

et la faire réviser par un technicien qualiﬁé avant son utilisation.

Purger le système d’hydromassage deux fois par mois ou plus souvent selon la fréquence d’usage, tel que

décrit dans la section « Purger le système » de ce guide.

L’utilisation répétée de produits d’hygiène et de beauté contenant des huiles peut endommager les

revêtements en plastique des composants de la baignoire à hydromassage. Ne pas utiliser de shampoings ou

d’huiles de bains à bases végétales.

L’action de la baignoire à hydromassage peut considérablement faire mousser une quantité de produit

moussant, même très petite, de savon, de shampoing ou d’huile pour le bain. Pour cette raison, nous vous

conseillons de ne pas utiliser ces produits dans votre baignoire à hydromassage.

Conforme FCC

FCC ID: N82-KOHLER001

Canada ID: 4554A-KOHLER001

Déclaration de conformité (Partie 15.19)

Cet appareil est conforme avec la Partie 15 de la réglementation FCC et RSS-210 Canada Industrie. L’appareil

est soumis aux deux conditions d’exploitation suivantes :

1. Cet appareil ne devrait pas causer d’interférences dangereuses, et

2. Cet appareil doit recevoir les toutes interférences reçues, ainsi que celles qui pourraient causer des

opérations non désirées.

Danger (Partie 15.21)

Tous changements ou modiﬁcations non expressément approuvés par la partie responsable garantissant la

conformité, pourrait annuler le droit à l’opérateur d’utiliser l’équipement.

Kohler Co. Français-2 1023246-5-C

Sommaire

Renseignements importants ......................................................... 1

Conforme FCC .................................................................. 2

Merci d’avoir choisi la compagnie Kohler ............................................... 3

Votre baignoire à hydromassage Kohler ................................................ 3

Clavier de l’utilisateur illuminé ....................................................... 4

Opération ...................................................................... 4

Télécommande .................................................................. 6

Entretien et nettoyage ............................................................. 7

Système de chasse ............................................................... 7

Garantie ....................................................................... 7

Dépannage ..................................................................... 9

Pièces de rechange .............................................................. 12

Merci d’avoir choisi la compagnie Kohler

Merci d’avoir choisi Kohler Co. Vos produits Kohler Co. sont l’expression d’une vraie passion pour la

conception, le travail soigné, le caractère artistique et l’innovation représentés par Kohler Co. Nous sommes

conﬁants que sa ﬁabilité et beauté surpasseront vos exigences les plus élevées, vous satisfaisant pendant les

années à venir.

Toute information contenue dans ce guide est basée sur l’information la plus récente du produit disponible

au moment de la publication. Chez Kohler Co, nous aspirons à remplir notre mission d’améliorer le niveau

d’un mode de vie agréable pour chaque personne affectée par nos produits et services. Nous nous réservons

le droit d’apporter des modiﬁcations aux caractéristiques, aux emballages et à la disponibilité des produits à

tout moment, et ce sans préavis.

Veuillez prendre s’il vous plaît quelques minutes pour étudier ce guide. Prêter une attention toute

particulière aux instructions d’entretien et de nettoyage.

Votre baignoire à hydromassage Kohler

Votre nouvelle baignoire à hydromassage est conçue pour relaxer, stimuler, revigorer et toniﬁer votre corps.

La baignoire à hydromassage consiste en les éléments suivants:

Clavier illuminé de l’utilisateur - Simple d’accès, il vous permet de démarrer ou d’arrêter la

baignoire à hydromassage. Il vous permet aussi d’accéder à tous les modes de la baignoire à

hydromassage et au réglage du débit d’eau ou de la puissance d’impulsion.

Télécommande - Toutes les fonctions de la baignoire à hydromassage sont à portée de main, aﬁn

d’améliorer d’avantage votre expérience de bain. Les fonctions de la télécommande sont identiques

à celles du clavier de l’utilisateur illuminé.

Moteur de pompe - Fournit une alimentation à vitesse variable et non bruyante pour faire circuler

l’eau.

Chauffe-eau - Aide automatiquement à maintenir une température d’eau de 40 °C (104 °F), se met

en marche lorsque la baignoire à hydromassage fonctionne et s’arrête lorsque le moteur de la pompe

est arrêté. Utiliser le clavier de l’utilisateur illuminé pour arrêter le chauffe-eau n’importe quand

pendant que la pompe fonctionne.

Effervescence - Huit ports effervescents émettent des milliers de bulles du style bulles de

Champagne qui offrent une expérience relaxante et apaisante.

Chromathérapie - Encourage la relaxation et fournit un spectre complet de couleur. La

chromathérapie peut être utilisée avec tous les modes d’opération, même lorsque la pompe n’est pas

en marche.

1023246-5-C Français-3 Kohler Co.

Page is loading ...

Kohler Hot Tub K-1418-CT User manual

Brand: Kohler

Model: Hot Tub K-1418-CT

Type: User manual

This manual is also suitable for

K-1418-CT

Download PDF

report

in other languages

français: Kohler Hot Tub K-1418-CT Manuel utilisateur
español: Kohler Hot Tub K-1418-CT Manual de usuario

Kohler Hot Tub K-1418-CT User manual

This manual is also suitable for

Kohler Hot Tub K-1418-CT User manual

in other languages

Related papers

Other documents