Stagg TIM JR 516 User manual

Brand: Stagg

Model: TIM JR 516

Type: User manual

TIM JR 516

USER MANUAL

Video demonstration on www.staggmusic.com

User Manual --> Support --> Drums & Percussion

10.b 10.a

13.a/b

31.c

11.a

11.b

11.c

11.d

12.a/b

10.h/i

10.d

10.c

10.g

10.f

1.a

1.b

11.e

1. Drum Head:

a. 10” tom-tom head x 2 pcs

b. 12” ﬂoor tom head x 2 pcs

c. 16” bass drum head x 2 pcs

2. Assembled snare drum x 1 pcs

3. Assembled 8” tom-tom x 1 pcs

4. 10” tom-tom shell x 1 pc + hoop x 2 pcs + 2 locked lugs

5. 12” ﬂoor tom shell x 1 + pc + hoop x 2 pcs

6. 16” bass drum shell x 1 pc + hoop x 2 pcs

7. Seat of drum throne

8. 8” hi-hat x 1 pair

9. 10” cymbal x 1 pc

10. Spare Part carton:

a. Cymbal stand x 1 pc

b. Central tom holder x 1 pc

c. Floor tom feet x 3 pcs

d. Bass drum feet x 2 pcs

e. Drum sticks x 1 pair

f. 3” (7.5cm) lug for 10” tom-tom x 6 pcs

g. 4.3” (11cm) lug for 12” ﬂoor tom x 8 pcs

h. 6” (15cm) lug for 16” bass drum x 8 pcs

i. Bass drum lug hook x 8 pcs

j. Lug spacers x 22 pcs

k. Drum key x 1 pc

11. Hi-hat Stand carton:

a. Pull rod x 1 pc

b. Clutch x 1 pc

c. Top section tube x 1 pc

d. Feet section x 1 pc

e. Feet section of drum throne

12. Snare Stand carton:

a. Basket arm x 1 pc

b. Feet stand x 1 pc

13. Drum Pedal carton:

a. Drum pedal x 1 pc

b. Beater x 1 pc

FULL PART LIST:

a. HI-HAT

Top hi-hat x 1

Feet section

Insert the foot pedal rod and tighten.

Open the feet and make sure

all feet are well secured to the ground.

Take out the pull rod from the top-section

tube and leave the clutch aside.

Insert the pull rod and tighten.

Tighten the feet & foot pedal rod.

Top section

Top-section tube

Pull rod

Clutch

Bottom hi-hat x 1

7 8

Insert the top-section tube

and tighten.

Place the bottom hi-hat.

Disassemble the clutch. Place the top hi-hat on the clutch rod.

Assemble the felt and the screw back. Fit the top hi-hat on the pull rod

and tighten the screw.

Pull open the legs and tighten.

You may leave some space for

playing open and close sound

Adjustable tilter for adjusting

the angle of bottom hi-hat

b. Throne

Seat Feet

Adjustable tube

3 4

Set the throne to appropriate

height and tighten.

Fit seat to the stand and tighten.

Pull open the legs and tighten.

Insert the basket arm to

appropriate height and tighten.

c. Snare drum

Stand-feet

Assembled snare drum

Basket arm

1. adjust the arm to

horizontal position

and tighten

3.loose the screw

and pull the arm

2. open the arms

5 6

Place the snare drum on basket. You may adjust the snare

by tuning the knob.

Place a head on the ﬂoor tom.

d. Floor tom & 10” tom-tom

Floor tom

Leg x 3 pcs

12” Head x2 pcs

Hoop x2 pcs

drum key x1 pc

Tension rod & spacer x 8 pcs

Place the hoop onto the head. Screw the tension rod to the lug.

NOTE: DO NOT FULLY TIGHTEN

Use the drum key to tune the tension rod.

Note: Do not fully tighten one rod at a time.

Please tune rods in the diametrical order as above.

Repeat several times until the tension of each rod is

equal. The higher tension you tune , the higher pitch

it would sound

Repeat the same procedure on the

other side until all lugs are half screwed.

Rod

Spacer

Hoop

Lug

The holes on the hoop

should be straight to the lug

1st

2nd

3rd

4th

7 8

Insert the ﬂoor tom legs into the leg

bracket to appropriate height and tighten.

1. Place the head with logo

on the front side of the bass drum.

2. Place the hoop onto the drum head.

Screw the tension rod to the lug.

NOTE: DO NOT FULLY TIGHTEN

Note: Do not fully tighten one rod at a time.

Please tune rods in the diametrical order as above.

Repeat several times until the tension of each rod is

equal. The higher tension you tune , the higher pitch

it would sound

Use the drum key to tune the tension rod.Repeat the same procedure on the

other side until all rods are half screwed.

1st

2nd

3rd

4th

7 8

Insert the legs to the leg bracket

and tighten.

Bass drum leg x 2 pcs

Prepare 8 sets of

bass drum tension rod + spacer + bracket

e. Bass drum

Hoop x2 pcs Bass drum x1

Drum key

tension rod set x8 sets

Bass drum head x2pcs

5 6

Insert the cymbal arm to

the holder bracket and tighten.

Unscrew the cymbal lock and

leave single felt on the holder.

1. Place the cymbal between 2 felts.

2. Place the spacer on the top.

3. Lock the cymbal.

Don’t forget to connect your

bass drum pedal before playing.

Hang 8” and 10” tom tom on the holder

The logo should face the audience.

Insert the tom tom holder

to the holder bracket and tighten.

f. Tom-tom, cymbal arm & bass drum pedal

Notes:

Stagg TIM JR 516 User manual

Stagg TIM JR 516 User manual

Stagg TIM JR 516 User manual

Other documents