1. Important Caution
2. Features
3. Specication
3-1 Receiver// US-8010D/ US-8010
3-2 Handheld Transmitter // Mh-700 / Mh-800 / Mh-700D
3-3 Body-pack Transmitter // PT-900B / PT-900BD
3-4 Optional Condenser Microphone
4. Part Identication & Accessories
4-1 Receiver// US-8010D/ US-8010
4-2 Handheld Transmitter // Mh-700 / Mh-800 / Mh-700D
4-3 Body-pack Transmitter // PT-900B / PT-900BD
4-4 Optional Condenser Microphone
4-5 Accessories
5. Preparing Procedures & Basic Operation
5-1 Receiver// US-8010D/ US-8010
5-2 Rack Mounting
5-3 System Operation
5-4 Handheld transmitter // Mh-700 / Mh-800 / Mh-700D
5-5 Body-pack Transmitter // PT-900B / PT-900BD
5-6 Installation of Condenser Microphones
6. Recommendation
7. Important Notice
1
1
2
2
2
3
3
6
6
6
7
7
11
12
12
13
13
14
15
16
18
19
INDEX
WIRELESS MICROPHONE SYSTEM
1
1. Important Caution
2. Features
Always makes all connections before plugging the unit into an AC power outlet.•
Do not leave the device in a place neither with high temperature nor high humidity.•
Always do not handle the power cord with wet hands!•
Keep the devices away from re and heat sources.•
Operated in UHF band where there is less RF interference than the VHF band. •
Equipped with a SAW lter can benet to reducing spurious RF content.•
Including balanced XLR output and unbalanced 1/4” output.•
Integrated antenna of the handheld transmier benets less hindrance for performer.•
Built-in noise mute and squelch circuit mode can validly resist extraneous noise. •
Body-pack transmier is available to work together with a lavalier mic. or headset mic.•
Space-saving half-rack housing design.•
2
3. Specication
3-1 Receiver
3-2 Handheld Transmitter
Model No....................................
Frequency Preparation......
Carrier Frequency Range
Frequency Stability...............
S/N Ratio...................................
T.H.D..................................
Display..............................
Display Contents...................
Controls............................
Audio Output Level............
AF Output Impedance.......
Squelch.............................
Operation Voltage.................
Output Connector................
Dimension(m/m)...............
US-8010D / US-8010
Crystal
600~960 MHz
±10KHz
> 105dB
<0.6%@1KHz
LED
Antenna, RF/AF Status
Power On/O, Audio Level
-12dB
600Ω
Pilot Tone, Noise and Mute
12-18 VDC, 150mA
1 XLR Balanced Socket
1 Unbalanced Ø6.3mm Phone Jack
221mm (W)* 40mm (H)* 152mm (D)
Mode No.............................................
Frequency Preparation..............
Carrier Frequency Range.........
RF Outputs........................................
Stability.................................
Frequency Deviation..................
LED Display......................................
Controls................................
Spurious Emissions.....................
Audio Frequency Response..
Battery..................................
Mh-700 / Mh-800 / Mh-700D
Crystal
600~960 MHz
10mW
±10KHz
±48KHz
Low Baery, Power On/O
Power On/O
<-50 dBC
50~16,000 Hz
UM3, AA 1.5V*2
WIRELESS MICROPHONE SYSTEM
3
3-3 Body-pack Transmitter
3-4 Optional Condenser Microphone
Model No..........................................
Frequency Preparation............
Carrier Frequency Range......
RF Outputs......................................
Stability.................................
Frequency Deviation................
LED Display....................................
Controls.................................
Spurious Emissions...................
Audio Frequency Response
Battery...................................
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
PT-900 / PT-900BD
Crystal
600~960 MHz
10mW
±10KHz
±48KHz
Power On/O, Low Baery
Power On/O, AF Level
<-50 dBC
40~18,000 Hz
UM3, AA 1.5V*2
CM-501
4P Mini XLR
100~15,000 Hz
Cardioid
-60±3 dB
2.2kΩ
130dB
Ø10.1mm(W)
* 26.4mm(H)
21.5g
CM-201
4P Mini XLR
60~15,000 Hz
Omni-directional
-60±3 dB
2.2kΩ
130dB
Ø5mm(W)
* 9mm(H)
20.7g
CM-125
4P Mini XLR
50~18,000 Hz
Omni-directional
-53±3 dB
4.4kΩ
130dB
Ø4mm(W)
* 11mm(H)
7g (cable excluded)
Lavaliere Microphone
4
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
CM-225
4P Mini XLR
50~18,000 Hz
Omni-directional
-53±3 dB
4.4kΩ
130dB
155mm(W)
* 134mm(H)
* 157mm(D)
17g (cable excluded)
CX-504
4P Mini XLR
30~18,000 Hz
Cardioid
-68±3 dB
680Ω
130dB
285mm(W)
* 55mm(H)
* 111.3mm(D)
56.3g
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Dimension(mm)..............
Net Weight............................
CM-204
4P Mini XLR
60~15,000 Hz
Omni-directional
-60±3 dB
2.2kΩ
130dB
125mm(W)
* 134mm(H)
* 157mm(D)
32.9g
CM-204U
4P Mini XLR
30~18,000 Hz
Cardioid
-68±3 dB
680Ω
130dB
205mm(W)
* 134mm(H)
* 157mm(D)
38.4g
CM-204UL
801C3 (3 pin mini XLR)
801C4 (4 pin mini XLR)
801CS (3.5 stereo plug)
100 ~ 18,000Hz
Cardioid
-75±3 dB
1.5kΩ
120dB
125mm(W)
* 134mm(H)
* 157mm(D)
18g (cable excluded)
Headset Microphone
WIRELESS MICROPHONE SYSTEM
5
Model No...............................
Connector..............................
Option Connector...........
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
CM-801/CM-804i
801C4 (4 pin mini XLR)
801C3 (3 pin mini XLR)
801CS (3.5 stereo plug)
60~15,000 Hz
Omni-directional
-64±3 dB
1.8kΩ
130dB
CM-8015/CM-825i
801C4 (4 pin mini XLR)
801C3 (3 pin mini XLR)
801CS (3.5 stereo plug)
50~18,000 Hz
Omni-directional
-53±3 dB
1.2kΩ
130dB
Ear-hook Microphone
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Good For.................................
Model No...............................
Connector..............................
Frequency Response......
Polar Paern..........................
Sensitivity (at 1000Hz)
Impedance.............................
Max. SPL for 1% THD
Good For.................................
CX-500
4P Mini XLR
20~20,000 Hz
Omni-directional
-58±3dB
1.5kΩ
130 dB
Violin
CX-508W
4P Mini XLR
50~18,000 Hz
Cardioid
-67±3 dB
220Ω
130 dB
Winds
CX-500F
4P Mini XLR
50~18,000 Hz
Omni-directional
-58±3dB
1.5kΩ
130 dB
Flutes
CX-520
4P Mini XLR
50~18,000 Hz
Supercardioid
-78±3dB
600Ω
148 dB
Harmonica
CX-516W
4P Mini XLR
50~18,000 Hz
Cardioid
-67±3 dB
220Ω
130 dB
Accordion
Compatible Instrument Microphone
6
4. Parts Identication & Accessories
4-1 Receiver // US-8010D / US-8010
Power On/O
RF indicator
AF indicator
Volume control
Antenna
DCV Input (12-18V DC/150mA)
Unbalanced 6.3mm jack socket
Balanced XLR socket
Interchangeable capsule module
Baery tray release knobs
Baery tray
Power On/O switch
LED Indicator
ID housing
4-2 Handheld Transmitter // Mh-800 / Mh-700D / Mh-700
1
4
7
9
12
10
13
11
14
2
5
8
3
6
Mh-800 Mh-700 / Mh-700D
1 2 3 4
5
6 8 7
1 2 3 4
5
6 8 7
9
11
13 14
10
12
9
11
13 14
10
12
WIRELESS MICROPHONE SYSTEM
7
Mic. input
Power On/o switch
Power Indicator
Antenna
AF level control
Baery tray
Baery tray cover
Carry case
Belt-loop
Clip
4 Pin Mini XLR
Windscreen
4-3 Body-pack Transmitter // PT-900B / PT-900BD
15
24
17
26
21
16
25
18
23
20
19
22
4-4 Optional Condenser Microphone
Lavaliere Microphone // CM-501 / CM-201 / CM-125
CM-501 CM-201 CM-125
26 26 26
25
24
24 24
22
23
16 15 19
18
17
20
21
WIRELESS MICROPHONE SYSTEM
9
31
34
37
37
33
36
39
39
32
35
38
38
Ear-hook Microphone // CM-801 CM-804i CM-8015 CM-825i
Boom
Adjustable Headband
Adjustable ear hook
Detchable Cable
Cable Clip
Windscreen
4 Pin Mini XLR
3 Pin Mini XLR
3.5 Stereo Plug
CM-801
CM-8015
CM-804i
CM-825i
31
31
31
31
34
34
34
34
33
33
33
33
36
36
36
36
32
32
35
35
35
35
Option
Option
WIRELESS MICROPHONE SYSTEM
11
AC/DC adaptor
Switching Power Supply(100V~240V , 50~60Hz)
Linear Power Supply (220V , 50Hz)
Linear Power Supply (220V , 60Hz)
Screwdriver
DR-900 dual rack adaptor
RP-900 panel cover
AF output cable (with Φ6.3 plug at both ends)
GC-80/GC-100 Guitar Cable
GC-80L/GC-100L Guitar Cable
4-5 Accessories
49
51
48
50
47
46
51 52
52
50
47
46
Option
Option
Option
Option
Option
Option
A
B
C
A
B C
MIXER
AC/DC ADAPTOR
AC POWER SOCKET
AUDIO OUTPUT
DC INPUT
2
1
48
49
12
5. Preparing Procedures & Basic Operation
5-1 Receiver // US-8010D / US-8010
(1) Audio Output Connector
e receiver equipped with both balanced XLR output and unbalanced φ 6.3mm jack output;
you can choose the proper way for using.
Connect one end of the Audio cable to the AF output socket in the rear panel of the receiver and
plug another end to the “MIC IN” input socket of a mixer or amplier. (Step 1 of Figure 1)
(2) Power connection
Connect one end of AC/DC adaptor cable to DC input socket in the rear panel of the receiver,
and plug another end into an AC outlet. (Step 2 of Figure 1)
MIXER
AC/DC ADAPTOR
AC POWER SOCKET
AUDIO OUTPUT
DC INPUT
2
1
WIRELESS MICROPHONE SYSTEM
13
5-2 Rack Mounting
5-3 System Operation
(1) Before mount receivers onto DR-900 rack adaptor, please release any cables from the rear of
the receiver.
(2) Turn over receiver and DR-900 rack adaptor simultaneously, there are 4 threaded holes each
in the boom of receiver and rack adaptor for inserting screws.
(3) Single receiver
Insert in a receiver through the front of DR-900 until it is rmly aached to the rack, then
screw on a RP-900 to another side of the rack.
(4) Dual receivers
e same way as above, put one receiver to each rack space.
Be sure to mute the audio signal of mixer or amplier before turning on the receiver and
transmier.
2
1
Figure 1 Figure 2 Figure 3 Figure 4
14
5-4 Handheld transmitter // Mh-700D / Mh-700 / Mh-800
(1) Mh-700D & Mh-700 & Mh-800 Handheld Transmier
1. Turn the microphone ball grille counter-clockwise
( Figure 1), press both release knobs to remove the
baery tray from the mic. housing ( Figure 2).
2. Insert two 1.5V baeries according to the correct polarity
(Step 1 of Figure 3) and return the baery tray back to
housing (Step 2 of Figure 3).
Aim the connecting pins exactly toward the cavities on the
boom side of detachable mic. capsule module ( Figure 4)
and tighten it clockwise!
2
1
Figure 1 Figure 2 Figure 3 Figure 4
WIRELESS MICROPHONE SYSTEM
15
5-5 Body-pack Transmitter // PT-900B / PT-900BD
(1) Basic operation
1. Slide the baery tray cover in the direction of the
arrow to open it, insert two 1.5V baeries according
the correct polarity, and return the cover.
2. Switch the transmier On
e On/O switch is located on the top of the
transmier.
3. Sensitivity adjusting
ere is a gain control adjustor in the up-le of its
back, you can adjust the level in 3 steps from 0 dB
to 30 dB.
AUDIO ADJUSTING STICKER
AF LEVEL CONTROL
ON/OFF
(2) Wearing the Body-pack transmier
e carry case allows body-pack transmier to be aached on performer’s belt, place the
antenna towards the back of his body. e Velcro tag around the belt and x it.
16
5-6 Installation of Condenser Microphones
(1) Lavaliere microphone
Aach lavaliere microphone to a tie, lapel, where is suitable for sound pick-up. Plug the
connector into input socket on the body-pack transmier.
(2) Headset microphone
Put the headband behind your head, and x the temples on your ears as shows, then
adjust the gooseneck to have best miking. Plug the connector into input socket on the
body-pack transmier.
(3) Instrument Microphones
e system is compatible with JTS various instrument microphones.
For detail please refer to user’s manuals of these microphones.
MIC IN
WIRELESS MICROPHONE SYSTEM
17
(4) Ear-hook Microphone
1. Lightweight Dual Ear Hook Microphone
Try on whether the headset is t.
Adjust the headband to a suitable width.
Tighten or loosen the curve of the ear-hook by twisting the loop or expanding it.
Curve and bend the boom to t your face.
Aach the detachable cable to a suitable place by a cable clip.
2. Lightweight Single Ear Hook Microphone
Try on whether the original curve is tight or loose.
Re-try and push the xed curve against your earlobe.
Curve and Bend the boom to t your face.
Aach the detachable cable to a suitable place by a cable clip.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Vonyx 141148 Operating instructions
-
Bowers Wilkins ISW-6 User manual
-
-
LD Systems LDU300 Wireless Microphone System User manual
-
Sense SE-500-DEH-T Owner's manual
-
Binary SE-300-WT-HAND Owner's manual
-
Sense SE-350-WT-HAND Owner's manual
-
Optimus MI-RD2CU16 User manual
-
Bogen Microphones User manual
-
TOA WT-5810 E01US/F01US Quick start guide