JTS US-8002D User manual

US-8002D

SINGLE / DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

US-8001D

Instruction Manual

ank you for choosing the JTS wireless system. In order to obtain the best eciency

from the system, you are recommended to read this instruction manual carefully.

TABLE CONTENTS

1. Important Cautions

2. Features

3. Specification

3-1 Overall System

3-2 Receiver

3-3 Transmier

3-4 Optional Condenser Microphone

4. Parts Identification & Accessories

4-1 Receiver

4-2 Handheld Transmier

4-3 Body-pack Transmier

4-4 Condenser Microphones

4-5 Optional Accessories

5. Preparing procedures & basic operation

5-1 Receiver

5-2 Baery Insertion of the Transmier

5-3 Rack Mounting

5-4 Installation of Condenser Microphones

6. System operation

7. Recommendations

01

02

03

04

06

08

10

12

13

14

16

17

18

20

Important Cautions

■ Always makes all connections before plugging the unit into an AC power outlet.

■ Do not leave the device in a place neither with high temperature nor high humidity.

■ Always do not handle the power cord with wet hands!

■ Keep the devices away from re and heat sources.

Features

■ Operated in UHF band where there is less RF interference than the VHF band.

■ Due to the PLL synthesized technology, the system oer 16 selectable channel.

■ e true diversity reception with 2 independent RF receivers ensure the stable transmission

and reception.

■ Adjustable squelch control can eectively reduce the noise.

■ Tuned antennas can benet the stable RF reception.

■ Built-in Tone key Squelch & Noise Mute detection are available to restrain the interference

signal.

■ Rugged metal housing can pass through the dicult environment.

■ Equipped with balanced XLR and unbalanced output allows great convenience.

■ Body-pack transmier provides phantom powering for condenser lavaliere and headset

microphones.

01 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

1

2

Specification

3-1 Overall System

3-2 Receiver

600 MHz~960 MHz

PLL Synthesized Control OSC

16 Channels

50 Hz~18KHz

24 Mhz

100M

US-8001D

±0.005%

>100 dB

-107dBm (12DB S/N AD)

>60 dB

<0.6%@1 KHz

LED

RF/AF Status, Channel,

Antenna A/B

Power On/O, Volume Control,

Channel Up/Down, Squelch level

-12 dB

Pilot Tone & Noise Mute

12-18V DC, 600 mA

1 Balanced XLR socket

1 ∅6.3mm Phone Jack (2.2 KΩ)

221mm(W)*40mm(H)*152mm(D)

US-8002D

±0.005%

>100 dB

-107dBm (12DB S/N AD)

>60 dB

<0.6%@1 KHz

LED

RF/AF Status, Channel,

Antenna A/B

Power On/O, Volume Control,

Channel Up/Down, Squelch level

-12 dB

Pilot Tone & Noise Mute

12-18V DC, 600 mA

2 Balanced XLR socket

1 ∅6.3mm Phone Jack (2.2 KΩ)

221mm(W)*40mm(H)*152mm(D)

RF Frequency Range

Oscillation Type

Channels

Audio Frequency Response

Band-width

Operation Range

Receiving Mode

Frequency Stability

S/N Ratio

RF Sensitivity

Image Rejection

T.H.D. (1 KHz)

Display

Display Contents

Controls

Audio Output Level

Squelch

Operation Voltage

Output Connector

Dimension(m/m)

3

02

Model No.

Type

Ball Grille Shape

Spurious Rejection

Stability

Frequency Deviation

S/N Ratio

Current Consumption

LED Indicates

Baery

Model No.

Type

Ball Grille Shape

Spurious Rejection

Stability

Frequency Deviation

S/N Ratio

Current Consumption

LCD/LED Indicates

Baery

PT-850B / PT-850Bmi

Body-pack

<-60dBc

±10KHz

±48 KHz

>100 dB (1 KHz-A)

100 mA

Power On/O

Low ba.

UM3,AA 1,5V*2

3-3 Transmitter

Mh-850 / Mh-8016

Handheld

Flat top

<-60dBc

±10KHz

±48 KHz

>100 dB (1 KHz-A)

100 mA

Power On/O

Low ba.

UM3,AA 1,5V*2

Mh-750

Handheld

Round top

<-60dBc

±10KHz

±48 KHz

>100 dB (1 KHz-A)

100 mA

Power On/O,

Low ba.

UM3,AA 1,5V*2

03 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

04

3-4 Optional Condenser Microphone

Lavaliere Microphone

Headset Microphone

Instrument Microphone

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

CM-501

100Hz~15,000Hz

Cardioid

-60dB±3dB

2.2k±30%

130dB

4 Pin Mini XLR

Windscreen

CX-201

60Hz~15,000Hz

Omini-directional

-60dB±3dB

2.2k±30%

130dB

4 Pin Mini XLR

Windscreen

CM-125

50Hz~18,000Hz

Omini-directional

-53dB±3dB

4.4k±30%

130dB

4 Pin Mini XLR

Windscreen

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

CM-204

60Hz~15,000Hz

Omini-directional

-60dB±3dB

2.2k±30%

130dB

4 Pin Mini XLR

Windscreen

CM-204U

30Hz~18,000Hz

Cardioid

-68dB±3dB

680±30%

130dB

4 Pin Mini XLR

Windscreen

CM-225

50Hz~18,000Hz

Omini-directional

-53dB±30%

4.4k±30%

130dB

4 Pin Mini XLR

Windscreen

Model No.

Frequency Range

Polar Paern

Sensitivity @ 1 KHz

Impedance

max. SPL for 1% T.H.D.

Connector Type

Standard Accessories

CX-516W

50Hz~18,000Hz

Cardioid

-70dB±3dB

2.2k±30%

130dB

4 Pin Mini XLR

Windscreen

CX-504

30Hz~18,000Hz

Cardioid

-68dB±3dB

680±30%

130dB

4 Pin Mini XLR

Windscreen

CX-508W

50Hz~18,000Hz

Cardioid

-67dB±30%

2.2k±30%

130dB

4 Pin Mini XLR

Windscreen

05 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

Ear-hook Microphone

Model No.

Frequency Response

Polar Paern

Sensitivity (at 1KHz)

Impedance

Max. SPL for 1% THD

Connector

CM-802/CM-804

60 ~ 15,000Hz

Omni-directional

-66±3 dB* (0.5mV)*0dB

=1V/μbar,1KHz

Rated impedance 2.2kΩ

130dB

4P Mini XLR

CM-815/CM-825

50 ~ 18,000Hz

Omni-directional

-53±3 dB* (2.24mV)*0dB

=1V/μbar,1KHz

Rated impedance 4.4kΩ

130dB

4P Mini XLR

Parts Identification & Accessories

4-1 Receiver

US-8001D Single Channel PLL Diversity Receiver

Power On

Channel Selector

RF indicator

AF indicator

Volume control

Antenna

DCV Input (12-18V DC/600mA)

Unbalanced 6.3mm jack socket

Balanced XLR socket

Accessories

AF output cable (With unbalanced ∅6.3 plug)

AC/DC adaptor

Scerwdriver

1

2

3

4

5

6

7

8

9

10

11

12

06

4

12

3

4

5

6

7

8

9

10

11

12

US-8002D Dual Channel PLL Diversity Receiver

Power On

Channel Selector

RF indicator

AF indicator

Volume control

Antenna

DCV Input (12-18V DC/600mA)

Unbalanced ∅6.3mm jack socket

Balanced XLR socket

Accessories

AF output cable (With unbalanced 6.3 plug)

AC/DC adaptor

Scerwdriver

1

2

3

4

5

6

7

8

9

10

11

12

07 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

7

8

99

12

3

4

5

6

10

11

12

08

4-2 Handheld Transmitter

Mh-850 Handheld Transmitter

Interchangeable capsule module

Baery tray release knobs

Baery tray

Channel selector

Power On/O switch

LED Indicator

ID housing

Mh-750 Handheld Transmitter

Interchangeable capsule module

Baery tray release knobs

Baery tray

Channel selector

Power On/O switch

LED Indicator

ID housing

1

2

3

4

5

6

7

8

9

10

11

12

13

14

8

10

9

11

12

13

14

Mh-8016 Handheld Transmitter

Interchangeable capsule module

Power On/O switch

Channel selector

Gain control

Baery tray

4-3 Body-pack Transmitter

PT-850B

Mic. input (mini 4 pin XLR socket)

Power On/O switch

Antenna

LED indiccator for power

and baery status

Baery tray

AF leavel control

Carry case

Belt-loop

Channel selector

09 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

1

2

3

4

5

2

3

4

5

6

7

8

9

10

11

12

13

14

6

10

PT-850Bmi

Mic. input (mini 4 pin XLR socket)

Power On/O switch

Antenna

LED indiccator for power

and baery status

Baery tray

AF leavel control

Carry case

Belt-loop

Channel selector

Aenuation Pad

4-4 Condenser Microphones

Lavaliere Microphone

Clip

4 Pin Mini XLR

Windscreen

1

2

3

4

5

6

7

8

9

10

11

12

3

4

9

6

8

5

13

11

12

13

10

7

11

CM-501

CM-125

CM-201

11 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

Headset Microphone

Gooseneck

Headband

4 Pin Mini XLR

Windscreen

Instrument Microphone

Gooseneck

Clip

4 Pin Mini XLR

Windscreen

1

2

3

4

5

6

7

8

3

4

5

6

78

1

2

5

CM-204

CM-225

CX-508W CX-516W

CM-204U

CX-504

12

Ear-hook Microphone

Boom

Adjustable Handband

Adjustable ear hook

4 Pin Mini XLR

Cable clip

Windscreen

Detachable Cable

4-5 Optional Accessories

DR-900 Dual Rack Adaptor

RP-900 Panel Cover

1

2

3

4

5

6

7

8

9

CM-804

CM-802

CM-825

CM-815

2

3

1

2

3

1

3

1

3

1

5

46

7

8

9

13 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

Preparing procedures & basic operation

5-1 Receiver

(1) Audio Output Connector

e receiver equipped with both balanced XLR output and unbalanced ∅6.3mm

jack output; you can choose the proper way for using.

Connect one end of the AF output cable to the AF output socket in the rear panel of

receiver and plug another end to the “MIC IN” input socket of a mixer or amplier.

(Step 1 of Figure 1)

(2) Power output connector

Connect one end of AC/DC adaptor cable to DC input socket in the rear panel of

receiver, and plug another end into an AC outlet. (Step 2 of Figure 1)

5

(Figure 1)

14

5-2 Battery Insertion of the transmitter

(1) Mh-850 & Mh-750 Handheld Transmier

1. Turn the microphone ball grille counter-clockwise (Step 1 of Figure 2), press

both release knobs to remove the baery tray from the mic. housing (Step 2 of

Figure 2).

2. Insert two 1.5V baeries according to the correct polarity, and return the baery

tray back to housing (Step 3 of Figure 3). Aim the connecting pins exactly

toward the cavities on the boom side of detachable mic. capsule module (Step 4

of Figure 3), and tighten it clockwise!

(Figure 2)

(Figure 3)

15 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

(2) Mh-8016 Handheld Transmier

Insert 2 pcs 1.5V AA baeries into the baery tray. (Figure 1)

Aer puing into the baery, switch on the power switch. (Figure 2)

(3) PT-850B / PT-850Bmi Body-pack Transmier

Slide the baery tray cover in the direction of the arrow to open it. Insert two 1.5V

baeries according to the correct polarity, and return the cover.(Figure 3)

(Figure 1)

(Figure 2)

1

2

(Figure 3)

16

5-3 Rack Mounting

(1) Before mount receivers onto DR-900 rack adaptor, please release any cables from

the rear of the receiver.

(2) Turn over receiver and DR-900 rack adaptor simultaneously, there are 4 threaded

holes each in the boom of receiver and rack adaptor for inserting screws.

(3) Single receiver

Insert in a receiver through the front of DR-900 until it is rmly aached to the

rack, then screw on a RP-900 to another side of the rack. (Figure 4)

(4) Dual receivers

e same way as above, put one

receiver to each rack space.

(Figure 4)

17 DUAL CHANNEL PLL DIVERSITY WIRELESS SYSTEM

5-4 Installation of condenser microphones

(1) Lavalier microphone

Aach a laveliere microphone to , tie, lapel, where is suitable for sound pick-up. Plug

the connector into input socket on the body-pack transmier. (Figure 1)

(2) Headset microphone

Put the headband behind your head, and x the temples on your ears as (Figure 2)

shows, then adjust the gooseneck to have best miking. Plug the connector into

input socket on the body-pack transmier. (Figure 2)

MIC IN

(Figure 2)

(Figure 1)

Page is loading ...

JTS US-8002D User manual

This manual is also suitable for

JTS US-8002D User manual

Related papers

Other documents