Somfy CD 1 x 4 P6 Installation guide

Brand: Somfy

Model: CD 1 x 4 P6

Type: Installation guide

CD 1 X 4 P Four motors control unit

The CD 1 x 4 P enables the individual control of 4 x 230 V AC motors. As the CD 1 x 4 P can be

used as local and master control, it is suitable for large and small installations. An additional group

control is no longer necessary with the CD 1 x 4 P.

The CD 1 x 4 P is suitable for roller shutters, awnings, as for exterior and interior Venetian blinds.

The slat rotation is adjustable.

General control is activated by IB compatible control units (such as e.g. a timer control, solar

and wind control or façade control) and transferred to all CD 1 x 4 P via the IB low voltage BUS

line.The 4 motors can be operated locally in one group by a local switch. Several push buttons and units can be connected

in parallel.

Two previously recorded intermediate positions can be called-up via an optional button (“IP key”). By connecting a switch, it is

possible to disconnect the automatic mode. All the safety commands, which are activated by the BUS line, have priority even

when the automatic mode is disconnected. The BUS line is powered directly by the CD 1 x 4 P.

The CD 1 x 4 P can be installed whether surface-mounted, in false floors, partition walls or false ceilings, or in an electrical

cabinet with a special DIN rail adapter.

ATTENTION : observe precaution for handling electrostatic discharge sensitive devices.

The printed circuit board is packed in an anti-static protective covering upon delivery.

INSTALLATION

guide

Ref. GMD021010

Installation

Assembly, testing, commissioning and trouble-shooting of the unit may only be carried out by a qualified electrician (respect the local

electrical standard). Disconnect all the connection wires which are to be fitted. Take the necessary safety measures to prevent uninten-

tional reconnection.

Proper functioning can only be guaranteed by expert installation and sufficient power supply.

1.1 Assembly / Wiring

CD 1 x 4 P6 for the DIN rail

When fitting the CD 1 x 4 P6 board on 35 mm DIN rail, two DIN rail adapters are used.

Put the board on the adapter and then clip the adapter onto the DIN rail.

When installing the unit in an electrical cabinet, please observe that a protection must be used to prevent direct access to the electri-

cally conductive components.

CD 1 x 4 P8 for surface-mounting

The board is screwed into a IP 54 box and can be installed in false ceilings, partition walls or false floors in damp rooms.

Motor 1 Motor 2

Mains

230V 50Hz

Live (L)

Neutral (N)

Ground (PE)

Jonction Box

Dry contacts control system :

Soliris IB

Chronis IB

Centralis IB

Outputs MCII

Local group control

motors 1 to 4

Local group control

motors 5 to 8

IB Bus line

to other CD 1x4 P

motor conrol units

Motor 3

SW1

AUTO ON/OFF

DOWN

AUTO ON/OFF

DOWN

Control

system

Mains SW1

Motor 4 Motor 5

CD 1x4 PCD 1x4 P

Motor 6 Motor 7 Motor 8

Connection wires:

max. 2.5 mm2 rigid wires or 1.5 mm2

stranded wires

PE (x6): Earth (all PEs are bridged)

L/N (x2) :Mains (both L and N are bridged)

M1 to M4: N/▲/▼ (x4)

Motors 1 to 4

Local 1: A /+/▲/▼/IP

on/off switch for all 4 motors (optional)

local switch (up/down/stop) for all 4 mo-

tors

local swirch for the intermediate position

(“IP key”) for all 4 motors (optional)

Bus 20 V: ▲/▼/COM (x2)

IB Bus line (coming and going)

SW1:

Dipswitch for selecting roller

shutters/awnings (ON)

or Venetian blinds (OFF) for all 4 motors.

2.1 Selecting between roller shutters/awnings and Venetian blinds

The selection is carried out via the dipswitch SW1 (see wiring diagram) :

- switch power supply off

- set dipswitch to ON ➜roller shutters/awnings mode

- set dipswitch to OFF ➜Venetian blinds mode

- turn power supply back on

When delivered, the dipswitch is set to Venetian blinds.

Warning : The CD 1 x 4P does not allow mixed installation.

2.2 Selecting between automatic mode and local mode (Automatic mode on/off)

Selecting between automatic mode and local mode requires a switch which has to be connected externally (see wiring diagram). In au-

tomatic mode, the general commands are automatically activated by IB compatible control units (such as a timer control, sun control, wind

control, general or façade control). In local mode, commands are activated by locally connected switches :

- connect the switch (see wiring diagram).

- switch open ➜automatic mode is activated.

All general and local commands are carried out. Local operation is not possible while general prioritary commands are activated (e.g. by

a wind control).

- switch closed ➜automatic mode is desactivated.

General commands are not carried out if they do not have priority. Only local commands are carried out in this case. If the general com-

mand has however higher priority (e.g. activated by a wind control), a command is given to the blind even though the automatic switch is

disconnected (safety function).

Instead of connecting the switch (depending on the function required) it is possible to leave the connection open or bridge it.

Possibility to select two tilting functions : European or US type.

"European" tilting mode:

- Press briefly less than 0,8s ➜the Venetian blind will be activated during the time of pressing (tilting of the slats).

- Press and hold more than 0,8s ➜the Venetian blind will be activated during 3 minutes (Up or Down control).

"US" tilting mode:

- Press briefly less than 0,2s or continuous control longer than 6s ➜the Venetian blind will be activated during 3 minutes (Up or Down control).

- Press and hold more than 0,2s and shorter than 6s ➜the Venetian blind will be activated during the time of pressing (tilting of the slats).

The product is initially configured in European tilting mode. Only one type of tilting mode can be set for all motors, a mixed mode is not

possible.

To change the tilting mode:

- Disconnect the mains supply of the motor control unit (cut off shortly the mains supply and turn it on again).

- During the next 30 seconds, press the connected “IP key” (see wiring diagram) for 5 seconds or, if no “IP key” is connected, bridge the

input of the "IP" connection to the "+" terminal for 5 seconds.

2.3 Operating ergonomics of the slat rotation

Local operation of the 4 motors is carried out via the local switch connected to the unit.

Several local switches can be connected in parallel.

Switches supplied by switch manufacturers as well as the SOMFY Centralis IB switch can ensure local operation.

- Connect the local switch (see wiring diagram)

- Press the corresponding key to move the motors UP or DOWN.

- Stop the 4 motors:

by pressing simultaneously the UP and DOWN keys.

or by pressing the reverse direction

or by pressing the same button again

or by pressing the “IP key”, if it is connected.

Settings

Local operation

The 4 motors can be moved to one or two selected intermediate positions. The recording and the calling-up of an intermediate position

can only be carried out by activating a connected “IP key” (see wiring diagram).

The first intermediate position is recorded from the upper end limit position of the system (shutter/awning up).

The second intermediate position is recorded from the lower end limit position of the system (shutter/awning down).

- Move the shutter/awning to the upper end limit position with the local switch.

- Press simultaneously the DOWN key and the “IP key” on the local switch (for approx. 2 seconds) until the shutter/awning moves downwards.

- Stop the shutter/awning at the desired position which is to be the intermediate position from the upper end limit position,by pressing:

Simultaneously the up and down keys

or the IP key

- The intermediate position can be adjusted with the local switch.

- Press and hold the “IP key” for at least 2 seconds ➜the intermediate position from the upper end limit position has been registered.

4.1 Recording the intermediate position from the upper end limit position

Upper end limit position

Lower end limit position

Intermediate position

- Move the shutter/awning downwards to the lower end limit position with the local switch.

- Press simultaneously the UP key and the “IP key” on the local switch (for approx. 2 seconds) until the shutter/awning moves upwards.

- Stop the shutter/awning at the desired position which is to be the intermediate position from the lower end limit position, by pressing:

Simultaneously the up and down keys

or the IP key

- The intermediate position can be adjusted with the local switch.

- Press and hold the “IP key” for at least 2 seconds ➜the intermediate position from the lower end limit position has been registered.

- When the 4 shutters/awnings are at the upper or lower end limit position, press briefly (less than 2 sec.) the “IP key”.

➜the shutters/awnings move to the recorded intermediate position.

4.3 Calling up a recorded intermediate position

4.2 Recording the intermediate position from the lower end limit position

- Move the 4 shutters/awnings to the intermediate position.

- Press the “IP key” for at least 10 seconds ➜the intermediate position has been deleted.

4.4 Deleting a recorded intermediate position

All 4 motors can be moved to a selected intermediate position with a slat angle. The intermediate position is recorded from the upper end

position. The slat angle can also be called up at any time after a DOWN command has been activated, whatever the position of the blinds.

The recording and the calling-up of the intermediate position can only be carried out by activating a connected “IP key” (see wiring dia-

gram).

Intermediate position With roller shutters and awnings

Intermediate position With Venetian blinds

- Move the Venetian blind to the upper end limit position with the local switch.

- Press simultaneously the DOWN key and the “IP key” (for approx. 2 seconds) until the blinds move downwards.

- Stop the blinds at the desired position which is to be the future intermediate position from the upper end limit position, by pressing:

Simultaneously the up and down keys

or the IP key.

- The intermediate position can be adjusted with the local switch.

- Press and hold the “IP key” for at least 2 seconds ➜the intermediate position has been registered.

Recording of slat setting

- Move the blind downwards until the slats are closed with the local switch.

- Press simultaneously the UP key and the “IP key” (for approx. 2 seconds) to set the required slat angle at the desired position which

is to be the future slat orientation setting.

- The angle of the slats can be adjusted with the local switch.

- Once the required slat angle has been obtained, press and hold the IP button for at least 2 seconds ➜the slat angle has been recorded.

5.1 Recording the intermediate position from the upper end limit position

5.2 Calling up the intermediate position with recorded slat angle

- When the 4 blinds are at the upper end limit position, press briefly the “IP key”.

➜the blinds move to the intermediate position followed by a rotation of the slats to the recorded slat angle.

Calling up the slat setting

- the recorded slat angle can be called up at any time after a local DOWN order (i.e. blinds with closed slats), by briefly pressing the “IP

key”.

5.3 Deleting the intermediate position

The intermediate position and slat setting are deleted separately.

Deleting the intermediate position

- Move the 4 blinds to their programmed intermediate position

- Press the “IP key” for at least 10 seconds ➜the intermediate position has been deleted.

Deleting the slat setting

- Move the blinds downwards

- stop the blinds in any position

- Press the “IP key” briefly ➜the blinds move to the set slat angle.

- Press and hold the “IP key” for at least 10 seconds ➜the slat setting has been deleted.

CD 1 x 4 P6 : ( 1 822 038) 100 x 142 mm

CD 1 x 4 P8 : ( 1 822 039) 160 x 165 x 60 mm

DIN rail adapter : ( 9 008 049) 65 x 107 mm

IP 54 box 160 x 165 x 60 mm

Nominal operating voltage 220-240 V ~ 50/60 Hz

BUS line voltage SELV, 9-20 V

Cross-section trip line 2 x 2 x 0,6 mm

Switching contact current-carrying capacity relay Cos phi > 0,8/3 A/230 V/50 Hz

Permissible cross-section of connection wire max. 2,5 mm2single wire

1,5 mm2stranded wire

Fuse Per output F3,15 AH; large disconnecting

capacity, 5 x 20 mm according to IEC 127-2/1

Temperature range 0° C to 40° C

(clean environmental conditions)

Protection factor against solid and splahproof Without box : IP 00

With box : IP 54

Protection class 1

Running time (switching time of relay) Approx. 3 minutes

CE EN 60730-1; EN 50081-1; EN50082-1

SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230

Technical data

Somfy CD 1 x 4 P6 Installation guide

Somfy CD 1 x 4 P6 Installation guide

Somfy CD 1 x 4 P6 Installation guide

Related papers

Other documents