Nyne NH-5000 User manual

Category
Docking speakers
Type
User manual

This manual is also suitable for

NH-5000
nyne.com
User Manual
Manual del usuario
Manuel utilisateur
FR
ES
EN
Série Home Audio
FR
Serie de audio para
el hogar
ES
Home Audio Series
EN
3
English
EN
Contents
1 Important 4
Safety 4
Notice 5
2 Introduction 8
What is Bluetooth technology? 8
Introduction to NH-5000 8
Overview 9
3 Preparation 12
Unpack 12
Connect power 12
Get the remote control ready
for use 12
Turn on the device 13
4 Operation 14
Use basic volume controls 14
Play and charge your iPod/
iPhone/iPad through the device 14
Listen from a Bluetooth
connected device 15
Listen from an auxiliary device 17
5 Specifications 18
6 Frequently asked questions (FAQ) 19
4EN
1 Important
Safety
The lightning fl ash with
arrowhead symbol within
an equilateral triangle
is intended to alert the
user to the presence of un-isolated,
dangerous voltage within the inside of
the device that may be of suffi cient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point
within an equilateral
triangle is intended
to alert the user to the presence
of important operating and
servicing instructions in the literature
accompanying the device.
Read these instructions before
operation.
Keep these instructions for future
reference.
Follow all instructions for installation,
use and maintenance of the device.
To avoid tilt or drop, place the device
on a fl at and hard surface.
To clean the device, disconnect
power fi rst. Clean only with soft and
dry cloth.
To ensure compatibility, only use
accessories recommended by the
manufacturer.
When the device is suddenly moved
from cold to warm surroundings,
condensation may form in the housing
of the device. Before use, leave the
device in the warm environment until
the moisture evaporates.
Keep the device away from heat
sources, such as a radiator, heater,
oven, amplifi er, naked fl ames or direct
sunlight.
Never block any ventilation openings.
Do not expose the device to sand
or dust, or cover it with items, such
as newspapers, table cloths, or
curtains.
Do not operate the device in an
enclosed cabinet. Leave suffi cient
free space around the device for
adequate ventilation.
Keep the device away from
moisture. Never expose the device
to rain, dripping or splashing. If water
penetrates into the device, unplug the
power cord and contact your dealer.
Continuous use in this case may result
in fi re or electric shock.
Make sure that the power supply
voltage is within the range indicated
on the label on the device or power
adapter. If you are not sure of the type
of power supply, consult you dealer or
local power company.
Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong is provided for your
safety. If the provided plug does not fi t
into your outlet, consult an electrician
for replacement of the obsolete outlet.
When connected to a power outlet,
power is always fl owing into the
device. To completely disconnect
power, unplug the power cord.
5
English
EN
When you unplug the power cord,
always hold the plug instead of the
cord.
Do not overload power strips and
extension cords. Overloading can
result in fi re or electric shock.
The wall socket should be located
near the device and be easily
accessible.
Where the mains plug or an appliance
coupler is used as the disconnect
device, the disconnect device shall
remain readily operable.
During lightning storms or when the
device is not to be used for a long
period of time, always unplug the
power cord of the device. Pulling on
the power cord can damage the wires
inside the cord and may cause fi re or
electric shock.
Do not attempt to repair or service the
device yourself. Opening or removing
the cabinet may expose you to
electric shock, and other hazards. If
repair is required, contact your dealer
and refer all servicing to qualifi ed
service personnel.
Do not use the device if any
abnormality occurs. If any smoke or
odor becomes apparent, unplug the
power cord and contact your dealer
immediately. Do not try to repair the
device yourself.
Avoid using dropped or damaged
appliances. If the device is dropped
and the housing is damaged, the
internal components may not function
normally. Unplug the power cord
immediately and contact your dealer
for repair. Continued use of the device
may cause fi re or electric shock.
Before moving the device, make sure
to disconnect the power cord and any
other cables fi rst.
To reduce the risk of electric shock,
do not touch any connector with wet
hands.
Use only with the cart
stand, tripod bracket,
or table specifi ed by
the manufacture, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
Never remove the housing of the
device.
Never lubricate any part of the device.
Never place the device on top of any
other electrical equipment.
Button cell batteries are dangerous if
swallowed! Keep batteries out of the
reach of children.
Notice
Modification
Any modifi cation (such as removing
the speaker grill) to the device,
without prior authorization from the
manufacturer, may void your warranty
and authority to operate the device.
FCC compliance statement
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant
to part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses,
6EN
and can radiate radio frequency
energy and, if not installed and used
in accordance with the instruction
manual, may cause harmful
interference to radio communications.
However, there is no guarantee
that interference will not occur in a
particular installation. If this equipment
does cause harmful interference to
radio or television reception, which
can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
Relocate the receiving antenna.
Increase the separation between
the equipment and receiver.
Connect the equipment into
an outlet on a circuit different
from that to which the receiver is
connected.
Consult the dealer or an
experienced radio/TV technician
for help.
This device complies with the FCC
Rules.
Operation is subject to the following
two conditions:
1This device may not cause harmful
interference, and
2This device must accept any
interference received, including
interference that may cause
undesired operation.
This device complies with FCC RF
radiation exposure limits set forth for an
uncontrolled environment.
This device and its antenna(s) must not
be co-located or conjunction with any
other antenna or transmitter.
Recycling
Packaging
Observe the local regulations for how
to dispose of the packaging materials.
Old product and battery
The old product shall not be treated
as household waste. Observe the
local regulations, and send the old
product and battery to the applicable
collection point for recycling of
electrical and electronic products
and batteries. Correct disposal of such
products helps prevent potentially
negative consequences on the
environment and human health. For
more information, consult your local
authority or dealer.
This is a CLASS II apparatus with double
insulation, and no protective earth
provided.
Copyright
“Made for iPod”, “Made for iPhone”,
and “Made for iPad” mean that
an electronic accessory has been
designed to connect specifi cally to
iPod, iPhone, or iPad respectively, and
has been certifi ed by the developer
to meet Apple performance
standards. Apple is not responsible
for the operation of this device or its
7
English
EN
compliance with safety and regulatory
standards. Please note that the use
of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
iPhone, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in
the U.S. and other countries. iPad is a
trademark of Apple Inc.
The Bluetooth word mark and logos
are owned by the Bluetooth SIG, Inc.
and any use of such marks by Nyne
Multimedia Inc. is under license.
8EN
2 Introduction
What is Bluetooth technology?
Bluetooth® is a wireless technology that
enables wireless data communication
over a short range between digital
devices. In general, Bluetooth-enabled
devices connect wirelessly with each
other within a range of 32 feet (10m).
In order for two Bluetooth-enabled
devices to work together wirelessly
to perform a certain function, both
devices should be compatible with the
same Bluetooth profi le that supports
this function.
Introduction to NH-5000
Thank you for purchasing our product.
This is a Bluetooth wireless docking
speaker system that supports Bluetooth
version 2.1.
This device is compatible with the
following Bluetooth profi les:
A2DP - (Advanced Audio
Distribution Profi le)
AVRCP - Audio/Video Remote
Control Profi le
With this device, you can:
Dock and charge your iPod/
iPhone/iPad.
Play music from your docked iPod/
iPhone/iPad.
Play video from your docked iPod/
iPhone/iPad on the large screen
of a TV connected to the device
through component video cables.
Play music from a Bluetooth-
enabled mobile phone or audio
source that is compatible with
A2DP, such as an iPod/iPhone/
iPad, Android smartphone, PC, or
Mac.
Play music from a connected
auxiliary device.
9
English
EN
Overview
Main unit
1 indicator
Light up in dock mode.
2 indicator
Light up in Bluetooth mode.
3
Light up in 3.5mm audio input (AUX)
mode.
4 indicator
Light up in RCA audio input mode.
5 touch button
Turn on the device or switch to
standby mode.
6 touch button
Select an audio source: iPod
(dock), BT (Bluetooth), AUX (3.5mm
audio input), or RCA (white/red
audio input).
7 Volume touchpad
Swipe to the left or right to
decrease or increase volume.
10 EN
8
Turn on or off power supply to the
device.
9
Connect the power adapter to AC
mains.
0
Connect to an auxiliary device,
such as a TV, DVD player, through
audio cables (white/red; not
supplied).
!
Connect to a TV through
component video cables (red/
blue/green; not supplied).
@ Dock for iPod/iPhone/iPad
#
Connect to an auxiliary device,
such as an MP3 player, through the
supplied 3.5mm audio cable.
$ Power/status indicator
Stay red in standby mode.
In Bluetooth mode, fl ash blue when
no Bluetooth connection has been
set up.
In Bluetooth mode, stay blue after
successful Bluetooth connection.
Flash red and blue briefl y during
any source or setting change.
Stay blue in dock, MP3, or RCA
audio input mode.
Remote control
1
Turn on the device or switch to
standby mode.
2
Turn up/down volume.
3
In dock/Bluetooth mode, press to
skip to the previous or next song.
In dock/Bluetooth mode, press and
hold to fast forward or backward.
4
In dock/Bluetooth mode, pause or
resume music/video play.
Mute Power
Vol+
Vol-
iPod BT
AUX RCA
Movie POP
Classic Rock
ag
b
e
f
c
d
11
English
EN
5 Source selection keys
Select an audio source: iPod
(dock), BT (Bluetooth), AUX (3.5mm
audio input), or RCA (white/red
audio input).
6 Keys of sound effect selection
Select a sound effect: movie, pop,
classic, or rock.
7
Mute or resume sound output.
12 EN
3 Preparation
Unpack
Unpack and identify the items of your
package.
1 x Bluetooth docking speaker
1 x remote control (with one
CR2025 button cell battery)
1 x AC power adapter
1 x 3.5mm audio cable
1 x User Manual
1 x Quick User Guide
1 x warranty card
Connect power
Warning:
Make sure that the power supply
voltage is within the range
indicated on the rating label at the
back of the device.
If you need other connections
(such as the audio and video
connection), complete these
connections before power
connection.
*)/4
Connect the power adapter.
round connector to the
socket on the back of the device
power plug to the wall socket
Get the remote control ready for
use
Warning:
To reduce the risk of explosion,
keep batteries away from heat,
sunshine, or fi re.
To reduce the risk of damage,
remove the battery when the
remote control is not to be used for
a long period of time.
Remove the protective tab on the
battery cover at the back of the
remote control.
13
English
EN
To replace the remote control battery:
1Remove the battery cover.
2Replace the old battery with a
new one (type: CR2025) with the
correct polarity.
3Mount the battery cover securely.
Turn on the device
1Turn the switch on the
back of the device to the
position.
The power/status indicator on the
front of the device lights up red.
2Press on the remote control
(or tap on the top panel).
The indicator of the last selected
audio source lights up.
The volume indicator bars on the
volume touchpad light up.
The power/status indicator fl ashes
red and blue alternately for a short
while, and then stays blue.
Tip:
If the device switches on to the
Bluetooth source, the power/status
indicator fl ashes blue when no
Bluetooth connection has been
set up.
To switch the device to standby mode:
• Press on the remote control
(or tap on the top panel) again.
14 EN
4 Operation
Use basic volume controls
You can use the basic volume controls
in any audio input mode, such as
dock, Bluetooth, 3.5mm audio input
(AUX), and RCA.
Press on the remote
control repeatedly (or swipe the
volume touchpad on the top panel to
the left or right) to adjust volume.
The volume indicator bars on
the volume touchpad change
accordingly as the volume
increases/decreases.
Press on the remote control once
to mute sound output.
Press on the remote control
again to resume sound output.
Press , , , or
on the remote control to select your
preferred sound effect.
Play and charge your iPod/
iPhone/iPad through the device
You can play and charge the
following iPod, iPhone, and iPad
models through this device:
Made for.
• iPad 2
• iPad
• iPhone 4S
• iPhone 4
• iPhone 3GS
iPod nano (3rd, 4th, 5th, and 6th
generation)
iPod touch (3rd, and 4th
generation)
Note:
If you have a protective case on
your iPod/iPhone/iPad, you may
need to remove it fi rst.
Dock your iPod/iPhone/iPad
Connect your iPod/iPhone/iPad to the
dock connector.
The device switches to the dock
source automatically.
The indicator on the top panel
lights up.
The device starts to charge your
iPod/iPhone/iPad.
Play music from your iPod/iPhone/iPad
When you dock your iPod/iPhone/
iPad onto the device, music play
starts automatically as long as there
is music in your iPod library. If music
play does not start automatically, start
music play on your iPod/iPhone/iPad
manually.
15
English
EN
During music play, you can:
• Press on the remote
control to skip to the previous/next
song.
Press and hold on the
remote control to fast forward/
backward in a song.
• Press on the remote control to
pause or resume music play.
Play video from your iPod/iPhone/iPad
1Connect the device to a TV with
component video cables (red/
blue/green; not supplied).
2Start video play on your iPod/
iPhone/iPad.
The video is played on the TV with
sound output from the Bluetooth
docking speaker.
During video play, you can:
Press and hold on the
remote control to fast forward/
backward.
• Press on the remote control to
pause or resume video play.
To switch to video play on your iPod/iPhone/iPad:
Press and hold on the remote
control.
To switch back to video play on the TV:
Press and hold on the remote
control again.
Listen from a Bluetooth
connected device
Pair with a Bluetooth-enabled device
Before using the Bluetooth feature of
NH-5000 for the fi rst time, you need to
pair NH-5000 with another Bluetooth-
enabled device, such as an iPod/
iPhone/iPad, Android smartphone, PC,
or Mac.
Note:
Make sure that NH-5000 and the
device to be paired are located
within the detectable range (32
feet or 10m).
16 EN
1Press on the remote control
(or tap on the top panel
repeatedly) to enter Bluetooth
mode.
The power/status indicator fl ashes
blue.
The indicator on the top panel
lights up and starts to fl ash.
The speaker enters pairing mode
automatically.
2Enable the Bluetooth function on
your device to be paired with
NH-5000.
The device to be paired with NH-5000
enters Bluetooth searching mode.
After a while, “NYNE NH-5000” is
displayed in the list of Bluetooth
equipment on the device to be
paired with NH-5000.
3Select “NYNE NH-5000”on the
device to be paired with NH-5000
to start pairing (if required, enter the
password “0000”).
After successful pairing and
connection, the indicator on the
top panel stops fl ashing and the
power/status indicator turns to blue
steadily.
Tip:
After successful pairing and fi rst-
time connection, if your paired
device fails to connect with NH-5000
automatically the next time, you may
need to select the device name of
NH-5000 from the list of Bluetooth
equipment on your paired device to
set up Bluetooth connection again.
Play music from a Bluetooth connected device
Notes:
To play/control music wirelessly
through the Bluetooth docking
speaker, make sure that your
device paired with NH-5000 is
compatible with Bluetooth profi les
A2DP/AVRCP. Check the user
manual of your paired device for
details.
Make sure that Bluetooth
connection has been set up
between the paired device and
NH-5000.
Start music play on your device paired
and connected with NH-5000.
You can hear music streamed
to the Bluetooth docking
speaker.
During music play, you can:
• Press on the remote
control to skip to the previous/next
song.
• Press on the remote control to
pause or resume music play.
17
English
EN
To use the (white/red) sockets:
1Connect audio cables (white/red;
not supplied).
one end to the
(white/red) sockets on the back of
the device
the other end to the audio out
(white/red) sockets on an auxiliary
device
2Press on the remote control
(or tap on the top panel
repeatedly) to select the RCA
audio input source.
The indicator on the top panel
lights up.
3Start music play on the auxiliary
device.
Listen from an auxiliary device
You can listen to music from an auxiliary
device through either the 3.5mm audio
input socket ( ) on the right side of
the dock or the (white/red)
sockets on the back panel of the Bluetooth
docking speaker.
To use the 3.5mm audio input socket:
Note:
Make sure that the auxiliary device
has a 3.5mm headphone socket.
1Connect the supplied 3.5mm
audio cable.
one end to the 3.5mm audio input
socket ( ) on the right side
of the dock
the other end to the 3.5mm
headphone socket on an auxiliary
device
The indicator on the top panel
lights up.
The device switches to 3.5mm
audio input (AUX) mode
automatically.
2Start music play on the auxiliary
device.
18 EN
5 Specifications
The technical specifi cations are
subject to change without prior notice.
General
AC power Input:
100-240V~50/60Hz
1500mA
Output: 22V
2500mA
Power
consumption
50W
Standby power
consumption
0.8W
Dimensions (W x
D x H)
400mm x 167mm x
203mm
Weight 3.5kg (net)
Amplifier
Output power
(L/R CH nominal)
2 x 15 W + 30 W
Frequency
response (L/R
CH)
30Hz - 20kHz at +/-
3dB
Sensitivity (L/R) 500mV
Signal to noise
ratio
75dB
19
English
EN
Check whether the sound output
is muted. Press on the remote
control to resume sound output.
Make sure that you have selected
an audio source for play.
If you have selected the dock
source, check whether you have
docked your iPod/iPhone/iPad
securely. If you have a protective
case on your iPod/iPhone/iPad,
remove it and try again.
If you have selected the Bluetooth
source, check whether the
Bluetooth connected device
supports Bluetooth profi le A2DP.
Check the user manual of the
device for details.
If you have selected the Bluetooth
source, check whether wireless
connection has been set up
between the paired device and
NH-5000.
If you are listening from an auxiliary
device, check the following points:
Make sure that you have started
music play on your auxiliary device.
Try to adjust volume on your
auxiliary device.
Check whether the 3.5mm audio
cable or audio cables (white/red)
have been connected securely
to both the Bluetooth docking
speaker and auxiliary device.
Why is there no picture or only distorted picture on the
TV?
Check whether you have
connected component video
cables to both the device and TV.
Check whether the TV is switched
on.
Check whether you have selected
the correct video input source on
the TV.
6 Frequently asked
questions (FAQ)
Never try to repair the device yourself
as you may void your warranty. When
you encounter any problems, read the
FAQ before you take the device for
repair. You may also visit www.nyne.
com/support for help.
Contact your dealer if any of the
following occurs:
The power cord frays or fails.
Liquid sprays or any object drops
into the device.
The device is exposed to rain or
other moisture.
The device is dropped or damaged
in any way.
The performance of the device
changes substantially.
Why is there no power?
Check whether you have
connected the power cable to
both the device and wall socket
securely.
Check whether the mains power is
interrupted.
Check whether you have turned
the switch on the back
of the device to the position.
Why is there no sound or only distorted sound?
• Press on the remote
control repeatedly (or swipe the
volume touchpad on the top
panel to the left or right) to adjust
volume.
• Press , , , or
on the remote control repeatedly
to adjust the sound effect.
20 EN
Why is it that I cannot control music play through
NH-5000?
Check whether the paired device
supports Bluetooth profi le AVRCP.
See the user manual of the device
for details.
Check whether the video is being
played on the screen of your iPod/
iPhone/iPad. If so, press and hold
on the remote control to switch
to video play on the TV.
Adjust the aspect ratio on the TV.
Why is there no response when I use the remote control to
operate the device?
Move closer to the device and try
again.
Aim the remote control directly at
the front of the device.
The battery may be used up.
Replace the battery with correct
polarity.
Why is my iPod/iPhone/iPad not charged after docking?
Check whether you have
connected the power cable to
both the device and wall socket
securely.
Check whether you have docked
your iPod/iPhone/iPad securely.
Check whether you have turned
the switch on the back
of the device to the position.
Why is it that I cannot find “NYNE NH-5000” on the device
already paired with NH-5000?
Check whether you have turned
on NH-5000.
Make sure that you have enabled
the Bluetooth function on the
device paired with NH-5000.
You may have failed to pair the
device with NH-5000. Repeat the
pairing procedures.
Check whether NH-5000 is
connected wirelessly with another
paired device. NH-5000 only
supports one Bluetooth connection
at a time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Nyne NH-5000 User manual

Category
Docking speakers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages