Tynetec ZXT811 User guide

  • Hello! I'm a chat assistant and I've reviewed the user manual for the Tynetec Heat Alarm ZXT811. This document details how to install, test, and maintain the device, which features a 10-year sealed battery, a test silence button, and is suitable for areas with dust, fumes, and moisture. I'm ready to answer any questions you have about its operation and features.
  • What does it mean when the unit chirps every 45 seconds and the yellow light flashes?
    How can I silence the low battery chirp?
    What does it mean if the unit chirps every 45 seconds and the yellow light flashes 20-25 seconds after?
    Where is the heat alarm best suited to be installed?
    How do I test the heat alarm?
Tynetec, a business unit of Legrand Electric Ltd
Cowley Road, Blyth Riverside Business Park, Blyth, Northumberland, NE24 5TF.
Tel: +44 (0) 1670 352371 www.tynetec.co.uk
Trusted Technology
Caring for People
869MHz
Heat Alarm
_________________________________________________________________________
________________________________________________________________
Doc No. FM0823 V1.07 Page 1
Compatible with Reach IP, Advent XT2, Carer Response
and Touchsafe Pro V4.01 onward
Complies with BS 5446-2:2003
Thermistek sensor technology
10 year sealed for life Lithium battery (typical)
Alarm point temperature range: +54oC to +62oC
Alarm sound level: 85dB(A) @ 3m
Large central Test/Silence ( ) button
Telecare Transceiver: 869.2125MHz Class 1.5
Digital Heartbeat
Weight: 199 grams
Dimensions: 132mm diameter x 60mm depth
Product Code: ZXT811
Positioning
Heat alarms are best suited to areas where dust, fumes and
moisture can cause nuisance alarms in smoke alarms such as;
kitchens, laundry rooms, lofts, and garages. Heat alarms must be
ceiling mounted in the centre of the room. They should be at a
distance no greater than 5.3m from the farthest wall, no greater
than 5.3m from a door to any room in which a fire might start
and no greater than 5.3m from the next heat alarm.
Heat alarms should not be wall mounted.
Thermistek technology activates the alarm sooner if it predicts a
significant rate of rise of temperature.
Refer to the Manufacturer’s instruction booklet for more
information on positioning.
Normal Operation
The red light will flash once every 45 seconds to indicate normal
operation.
Alarm Condition
The unit will repeatedly sound 3 loud beeps and the red light will
flash every second. Check if there is a fire hazard and leave the
building immediately.
DANGER: Never ignore any alarm. If you are not certain of the
cause, leave the building immediately.
Alarm Silence
In the event of a known false alarm you can temporarily silence
the heat alarm by pressing the Test/ button. The alarm will
automatically return to full sensitivity within 10 minutes.
NOTE: If the level of heat is very high the alarm silence will be
overridden, and the alarm will continue to sound.
Low Battery Condition
If the unit chirps every 45 seconds and the yellow light flashes at
the same time, this indicates the battery is running low. The low
battery condition will also be reported automatically to the Alarm
Receiving Centre (ARC) or the local Manager once a day.
The telecare transceiver module also contains a battery - this is
self-tested once a day, if it’s low for 7 consecutive days a low
battery condition will be reported once a week.
The complete heat alarm should be replaced as soon as possible
within 30 days.
Sleep Easy Feature
Low battery warnings often start when it is inconvenient to
replace the alarm. You can silence the audible low battery chirp
for a period of 8 hours by pressing the Test/ button. After this
period the audible chirp will start again. This process can be
repeated up to 10 times. The alarm will still detect heat during
this time, however it must be replaced within 30 days.
Fault Condition
If the unit chirps every 45 seconds and the yellow light flashes
20-25 seconds after, this indicates a fault with the heat alarm and
it should be replaced immediately.
Out of Range Notification (Reach IP)
The Reach IP can monitor all radio peripheral devices to
determine whether they have been damaged or removed from
an installation. Should the Reach IP be unable to detect a device’s
heartbeat it will automatically generate a “radio out of range”
notification. Firstly, investigate if there’s a genuine reason for the
alert, if not, arrange for the peripheral device to be replaced
immediately. The “Radio out of range timer” can be set from 30
hours to 99999 hours in Pulse CMP. “Radio supervision” can be
disabled by unchecking the tick box associated with each
peripheral device in Pulse CMP.
Maintenance
Test the heat alarm once every month.
Clean once every 3 months using a vacuum cleaner fitted with
the soft brush attachment.
Do not use solvents or cleaners on the heat alarm, the unit can
be wiped with a damp cloth.
Disposal
Waste electrical products should not be disposed of
with normal household waste. The heat alarm is ideally
suited for disposal within the waste electronic and
electrical equipment (WEEE) recycling scheme. Please
recycle where facilities exist. Check with your local authority or
contact your supplier for recycling/disposal advice.
Warning
The heat alarm contains a powerful Lithium battery.
If tampered with the battery may be damaged and create a fire
hazard. No attempt should be made to open the case or remove
the battery. Do not incinerate.
Tynetec, a business unit of Legrand Electric Ltd
Cowley Road, Blyth Riverside Business Park, Blyth, Northumberland, NE24 5TF.
Tel: +44 (0) 1670 352371 www.tynetec.co.uk
Trusted Technology
Caring for People
869MHz
Heat Alarm
_________________________________________________________________________
________________________________________________________________
Doc No. FM0823 V1.07 Page 2
The battery power will
now be switched on and
the red light will flash once
every 45 seconds to show
that it is active.
The unit will sound an
audible alarm consisting
of 2 cycles of 3 loud
beeps, then stop
automatically.
The Radio ID is a 10-digit code
printed on the radio module
label on the back of the
heat alarm
ZXT811
S:081923618
Iss-1
149308028A
19W8
How to install the Heat Alarm
Make sure you have read and understood the instructions on
positioning the alarm before starting.
The base plate must be securely fixed to the ceiling. Use the
fixing slots on the base plate as a guide when marking the
position of the drill holes. Fix with the screws and plugs
provided.
Alternatively, the base plate can be fixed with the self-adhesive
pads provided. Ensure the surface is smooth, clean and dry.
Press hard to make sure the pads are properly adhered.
Position the alarm on the base plate then twist it clockwise
until the alarm is fully locked in position.
IMPORTANT: when the heat alarm is fitted to the base plate it
enters a power-up initialization period. It is possible the first
Test/ button press will be missed during this period.
All subsequent Test/ button presses will function correctly.
Heat will always be detected during the initialization period.
WARNING: Removing the alarm from its base plate will
de-activate the unit and prevent it from detecting heat.
How to test the Heat Alarm
Press the Test/ button in the centre and release.
The red light on the alarm will flash rapidly during the audible
signal. Do not test with a naked flame.
Telecare Radio ID
The heat alarm includes a plug-in radio transceiver module to
communicate with the Reach IP, Advent XT2 or Carer Response.
Registering the Heat Alarm onto a Reach IP
Login to Pulse CMP (www.tynetecpulse.com) and enter the
Reach IP Serial No. in the ALARM UNIT view.
Press the Accessories button and enter the Radio ID code,
Location and Equipment type. Press Save then Synchronize.
IMPORTANT: when the heat alarm is installed a test call must be
made to check operation and start the digital heartbeat.
Alternatively, with the Reach IP in normal operating mode undo
the fixing screw and remove the stand or connector cover to
access the Power button.
Press the Power button to enter Control Mode, then press and
hold the button until the unit announces “add radio device
then release.
Press the button to confirm then activate the heat alarm by
pressing the Test button.
The Reach IP unit will sound a high beep if it’s a new device and
announce “range test mode.
Press to confirm, or press to step to the next function, or
press to exit the mode.
Press the test button on the heat alarm to check operation.
Registering the Heat Alarm onto an Advent XT2
Press the Settings button on the Home page of the Manager’s
Panel. Press the Manager (or Engineer) button, enter the
password and press the Programming button.
Select the Program Radio Devices option from the tabs along the
bottom of the screen.
Press Flat ID and enter the flat number the heat alarm is being
installed in. Enter 4-digits e.g. 0014.
Press Radio ID and enter the 10-digit code taken from the radio
module label on the back of the heat alarm.
Press Room Locations and select where the heat alarm is located
from the on-screen options e.g. Kitchen.
Press the Send button to update the XT2 system.
Press the test button on the heat alarm to check operation.
Power Button
Tynetec, a business unit of Legrand Electric Ltd
Cowley Road, Blyth Riverside Business Park, Blyth, Northumberland, NE24 5TF.
Tel: +44 (0) 1670 352371 www.tynetec.co.uk
Trusted Technology
Caring for People
869MHz
Heat Alarm
_________________________________________________________________________
________________________________________________________________
Doc No. FM0823 V1.07 Page 3
Registering the Heat Alarm onto a Carer Response
Refer to the Carer Response
user manual for full details
of the button functions and
how to navigate the menus.
From the Main menu select
Programming.
From the Programming menu select
Add transmitter.
The display will prompt you to
Activate the transmitter…
Press the test button on the heat alarm.
The Carer Response will beep and the display will change to the
Add transmitter menu with a box showing No ID.
Press then to select Room, then press
Press to select the room number box 0000.
Press to select the first digit, press to move between the
digits and press or to change each digit.
Press when the correct room number is displayed.
Press to select the alarm type box None.
Press then to select Smoke Detector then press
Press the button to select Save then press
The display will show Radio ID saved to memory…
Return to the Main menu and select Quit.
Press the test button on the heat alarm to check operation.
Registering the Heat Alarm onto a Touchsafe Pro
Login to the Master Touchsafe Pro Nursecall Panel (must be
V4.01 onward) using an Engineer or Manager password.
From the Main Menu page select the Telecare option to open
the screen shown below.
Touch the Add Telecare Device box and enter the Telecare
device 10-digit Radio ID using the on-screen keypad.
Touch the Filter box and enter the zone you want to add the
Telecare device to using the on-screen keypad.
Touch the Room box and select the Callpoint ID from the list
that will be used to cancel the Telecare alarm.
Touch the Save button on the keypad.
Touch the Close button to exit.
Press the test button on the heat alarm to check operation.
Declaration of Conformity
We declare this product complies with the
relevant UK legislation on condition that it is used in
the manner intended, and in accordance with the
current installation standards and/or the
manufacturer's recommendations. A copy of the full UKCA
Declaration of Conformity is available on request.
We declare this product complies with the
relevant European legislation on condition that it is
used in the manner intended, and in accordance with
the current installation standards and/or the
manufacturer's recommendations. A copy of the full CE
Declaration of Conformity is available on request.
Chris Dodd
CEO
Legrand Assisted Living & Healthcare
/