TrailFX DHS024B Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

Page 1 of 6 Rev B 03262020
www.TrailFX.com
TrailFX Drop Down Step
Part No. DHS024B / DHS023B
Fits: Chevrolet/GMC - Silverado/Sierra 1500 Crew Cab 2004-2013;
25/3500 2001-2019 (Body Mount), Chevrolet/GMC - Silverado/Sierra
Product image
TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF
THE TAILGATE VENT COVER CAREFULLY.
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
PARTS LIST:
Item Qty Part Description Tools Needed
1 1 Step Bar Driver Side 13 MM SOCKET & WRENCH
2 1 Step Bar Passenger Side 14 MM SOCKET & WRENCH
3 1 Front Mounting Bracket Driver Side 15 MM SOCKET & WRENCH
4 1 Front Mounting Bracket Passenger Side 18 MM SOCKET & WRENCH
5 1 Center Mounting Bracket Driver Side 21 MM SOCKET & WRENCH
6 1 Center Mounting Bracket Passenger Side RATCHET
7 1 Rear Mounting Bracket Driver Side TORQUE WRENCH
8 1 Rear Mounting Bracket Passenger Side
9 1 Support Strap Driver Side
10 1 Support Strap Passenger Side
11 2 M10 U Bolt
12 6 M10 Hex Nut
13 2 M10 Hex Head Bolt
14 6 M10 Lock Washer
15 8 M10 Flat Washer
16 12 M10 Flange Bolt
17 12 M10 Flange Nut
ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTEN-
ERS TO 30 ft. - lbs. Torque Body Mount Bolts to GM spec.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
1 866 638 4870
60 min Drilling Not
Required
Cutting Not Re-
quired
POLISHED STAINLESS STEEL – LIMITED LIFETIME
POWDER COATED BLACK – 3 YEARS
Mounting Kit Images
Item 3 Item 4 Item 5 Item 6 Item 7 Item 8 Item 7 Item 8 Item 9 Item 10
Extended Cab and Double
Cab Rear Brackets Crew Cab Rear Brackets
Page 2 of 6 Rev B 03262020
www.TrailFX.com
2. Move to the center mount position and insert the sup-
plied U bolt. See Figure 2.
INSTALLATION PROCEDURE
1. Start at the front driver side of the vehicle and remove
the factory bolt from the puck mount on the frame.
Grab the front driver side mount bracket and loosely
install with the factory bolt. See Figure 1.
3
11
5
9
FIGURE
FIGURE
FIGURE
Center Driver Side Shown
Center Driver Side Shown
Front Driver Side Shown
3. Move on to the center body puck mount on the driver
side. Loosely install the center bracket with the factory
bolt. See Figure 3.
Page 3 of 6 Rev B 03262020
www.TrailFX.com
INSTALLATION PROCEDURE
4. Loosely install the center mount bracket with the
support bracket using the supplied M10 hardware.
See Figure 4.
5. Move on the rear body puck mount and loosely in-
stall the rear mount bracket with the factory bolt.
Crew Cab shown. See Figure 5. Go to Page 4 for
Extended Cab and Double Cab applications.
7
FIGURE
Rear Driver Side Shown
Crew Cab Shown
Center Driver
Side Shown
FIGURE
Page 4 of 6 Rev B 03262020
www.TrailFX.com
17
FIGURE
INSTALLATION PROCEDURE
6. Move on the rear body puck mount and loosely in-
stall the rear mount bracket with the factory bolt.
Extended Cab and Double Cab shown. See Figure 6.
7. Loosely Install step bars respectively to either side
using the M10 hardware provided with the step bars.
See Figure 7.
8. Align and adjust the step bars as needed and fully
tighten all hardware.
9. See Figure 8 for reference.
7
16
FIGURE
Ext. Cab Double Cab Shown
Rear Driver Side Shown
FIGURE
FRONT
DOUBLE CAB DRIVER SIDE SHOWN
CREW CAB SIMILAR
Item 3 Item 5
Item 7
Page 5 of 6 Rev B 03262020
www.TrailFX.com
COMPLETE INSTALLATION
Page 6 of 6 Rev B 03262020
www.TrailFX.com
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of pur-
chase by the original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a
particular purpose or an intended use. If the product is found to be defective, KAO may replace or repair the product at our option,
when the product is returned prepaid, with proof of purchase. Alteration to, improper installation, or misuse of this product voids the
warranty. KAOs liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for any
incidental or consequential loss or damage.
Check out these other TrailFX Products!! www.TrailFX.com
PRODUCT CARE
1.
FAQs
1. Mounting bracket are not getting Installed properly.
In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / Passenger side
mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue.
2. Products are thumping / rattling after installation.
Please ensure that all required mounting brackets / hardwares are installed & tighten correctly. Suggest using white lithium / regular grease between the
metal to metal contact surfaces.
3. Missing / Excess Hardware.
Recheck hardware count as per the part list.
4. Product not installing properly.
Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

TrailFX DHS024B Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI