2. Computers & electronics
  3. Audio & home theatre
  4. Home audio sets
  5. ONKYO
  6. (HT-R494)
(HT-R494)

ONKYO (HT-R494), HT-R494, HT-S5805 User manual

  • Hello! I am an AI chatbot trained to assist you with the ONKYO (HT-R494) User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
En
HT-R494
AV RECEIVER
This manual includes information needed when
starting up and also instructions for frequently
used operations. The Advanced Manual is
published on the web for ecological reasons and
has more detailed information and advanced
settings.
Basic Manual
http://www.onkyo.com/manual/htr494/adv/en.html
Advanced Manual
found here
HT-R494_BAS_En_SN29401998_1503xx.indd 1 2015/03/12 15:07:40
En-2
ContentsFeatures
Advanced Manual (on the web)
The Advanced Manual, published as an e-manual on the
web, has more detailed information and advanced settings.
The Advanced Manual is created in a format that makes
it easy to read on a PC or Smartphone. The Advanced
Manual has the following content:
● Details on AM/FM reception
● Operating Music Files with the Remote Controller
● Using the Listening Modes
● Advanced Settings
● Operating Other Components with the Remote
Controller
● Advanced Speaker Connection
● Connecting and Operating Onkyo RI Components
● Troubleshooting
● Reference Information
Advanced Manual found here
http://www.onkyo.com/manual/htr494/adv/en.html
● Equipped with 7 ch amplifier
● Supports playback in Dolby Atmos format which
provides 360-degree placement and movement of
sounds including overhead sound
● Dolby Surround listening mode expands 2 ch, 5.1 ch or
7.1 ch source to available speaker configurations
● Equipped with 4K compatible HDMI IN/OUT jacks (To
play 4K or 1080p video, use a high speed HDMI cable
or high speed HDMI with Ethernet cable)
● Supports the HDMI Standby Through function which
allows signal transmission from players to the TV in
standby state
● Supports HDCP2.2, a strict copy-protection for providing
high quality content
● Supports ARC (Audio Return Channel)
● Supports Bluetooth
®
connection
● A/V Sync Function to correct deviation of audio and
video
● 32 bit DSP (Digital Signal Processor) with excellent
calculation performance
● Music Optimizer™ for compressed digital music files
● Phase Matching Bass System
● Automatic speaker setup available using supplied
calibrated microphone (AccuEQ Room Calibration)
● Supports multi-language on-screen displays
English, German, French, Spanish, Italian, Dutch,
Swedish, Russian
1
, Chinese
1, 2
1
European, Australian and Asian models only
2
OSD is not displayed when the input selector is "BLUETOOTH".
Refer to the back cover for supplied accessories.
Basic Manual (this manual)
Front Panel ..........................................................................3
Rear Panel...........................................................................4
Step 1: Connections ����������������������������������������������5
1 Connecting the TV and Players ........................................5
･ Connection to TV ..........................................................5
･ Connection with a player that has a HDMI jack ............6
･ Connection with a player that does not have a
HDMI jack ......................................................................6
2 Connecting the AM/FM Antenna.......................................6
3 Connecting Speakers .......................................................7
･ Speaker layout ..............................................................7
･ Instructions on how to connect speakers ......................8
Step 2: Setting Up ��������������������������������������������������9
1 Turning the Power On ......................................................9
2 Making Automatic Speaker Setting ..................................9
3 HDMI Setup ....................................................................10
･
HDMI CEC (RIHD) ........................................................ 10
･ HDMI Standby Through ..............................................10
･ ARC (Audio Return Channel) ......................................10
Step 3: Playing Back ������������������������������������������� 11
1 Basic Operations ............................................................11
･ Part names and functions of the remote controller .....11
･ Display ........................................................................12
2 Bluetooth
®
  ......................................................................12
3 AM/FM Radio .................................................................12
4 Quick Setup Menu ..........................................................13
5 Other useful functions ....................................................14
Troubleshooting .................................................................15
Specifications ....................................................................16
Table of display resolutions ...............................................17
Resolutions supported by HDMI ........................................17
Supplied Accessories ..........................................Back cover
HT-R494_BAS_En_SN29401998_1503xx.indd 2 2015/03/12 15:07:40
En-3
1 23 89
FG
HJ
4
K
56 7
I
MLN
(European, Australian
and Asian models)
Front Panel
1 zON/STANDBY button: Turns the unit on or into
standby mode.
2 BLUETOOTH indicator: Flashes while pairing with a
Bluetooth-enabled device is in progress and stays lit
when pairing is completed.
3 DOLBY ATMOS indicator: Lights when playing Dolby
Atmos.
4 SUBWOOFER Level buttons: Adjust the volume of the
Subwoofer.
5 Remote control sensor: Receives signals from the
remote controller.
6 DIMMER button (North American and Taiwanese
models): Switches the brightness of the display.
RT/PTY/TP button (European, Australian and Asian
models): Can be used when receiving the station
transmitting text information.
7 Display: Refer to page 12 for details.
8 SETUP button: Used when making settings.
9 Cursor buttons,
l
TUNING
j
button,
d
PRESET
c
button and ENTER button: Move the cursor and
confirms the selection. When listening to AM/FM
broadcasting, tune in to the station with
l
TUNING
j
or
select the registered station with
d
PRESET
c
.
F RETURN button: Returns the display to the previous
state.
G MASTER VOLUME: Allows you to adjust the volume.
H MUSIC OPTIMIZER button: Turns on/off the MUSIC
OPTIMIZER function that improves the quality of the
compressed audio.
I PHONES jack: Stereo headphones with a standard plug
are connected.
J TONE and Tone Level buttons: Adjust the high tone
and low tone.
K Input selector buttons: Switch the input to be played.
L LISTENING MODE buttons: Allow you to select the
listening mode.
M AUX INPUT VIDEO/AUDIO jacks: A video camera or
such other device is connected.
N SETUP MIC jack: The supplied speaker setup
microphone is connected.
HT-R494_BAS_En_SN29401998_1503xx.indd 3 2015/03/12 15:07:41
En-4
1 2 3 4 5 6 7
8 9 F G H I J
Rear Panel
1 TUNER AM/FM (75Ω) terminals: The supplied
antennas are connected.
2 to TV jack: Connect to a TV using a HDMI cable.
Change the input selector to "TV" to hear audio from the
TV.
¼ If your TV does not support ARC, you need connection F in addition to
this connection.
3 BD/DVD jacks: Connect to a Blu-ray Disc Player or
DVD Player using a HDMI cable. This corresponds with
the "BD/DVD" input selector.
4 CBL/SAT jacks: Connect to a Cable Set-top box using
a HDMI cable. This corresponds with the "CBL/SAT"
input selector.
5 GAME 1 jack: Connect to a Game console using a
HDMI cable. This corresponds with the "GAME 1" input
selector.
6 STRM BOX jacks: Connect to a Streaming Media
Player. When a power supply is required, connect using
a USB cable to the POWER OUT port. This corresponds
with the "STRM BOX" input selector.
7 Power cord
8 RI REMOTE CONTROL jack: An Onkyo product with RI
jack can be connected and synchronized with this unit.
9 CD jacks: Connect to audio equipment such as a CD
Player using a digital optical cable. This corresponds
with the "CD" input selector.
F TV jacks: If your TV does not support ARC, you need
to connect this jack to the audio output jack on the TV,
in addition to connection 2. This corresponds with the
"TV" input selector.
G GAME 2 jacks: Connect a game console that has
component video jacks. This corresponds with the
"GAME 2" input selector.
H VCR jacks: Connect to a Video Cassette Recorder. This
corresponds with the "VCR" input selector.
I SUBWOOFER jack : A subwoofer with built-in amplifier
is connected.
J SPEAKERS jacks : Speakers are connected. Up to 7
channels of speakers can be connected.
HT-R494_BAS_En_SN29401998_1503xx.indd 4 2015/03/12 15:07:41
Step 1: Connections
En-5
HDM
I
IN
HDMI
OUT
AV OUT
Connection example
1 Connecting the TV and Players
Before Start
● Connect this unit between the TV and
player.
● To select the source to play, select
the input selector button with the
same name as the jack to which it is
connected. Input switches automatically
when you have connected equipment
that conforms to the CEC (Consumer
Electronics Control) standard to this unit
using a HDMI cable. ()
● This allows audio and video signal
transmission from players to the TV
even if this unit is in standby. (HDMI
Standby Through function) ()
● The power cord must be connected
only after all other connections are
completed.
¼ It is necessary to make appropriate settings to enable
this function. See "3 HDMI Setup" of "Step 2: Setting
Up".
Cable used for connection (sold
separately)
HDMI cable
Component video cable
Composite video cable
Digital coaxial cable
Digital optical cable
Analog audio (RCA) cable
Connection to TV
Connect the "to TV" jack and the HDMI IN
jack of the TV with a HDMI cable. This is
the only connection necessary with a TV
that supports ARC. If your TV does not
support ARC, you need to connect the "TV"
jack to the audio output jack on the TV with
a digital optical cable or an RCA cable, in
addition to this connection to the "to TV"
jack.
¼ This function enables you to play the audio from
the TV through the speakers of this unit just by
connecting this unit and the TV with a single HDMI
cable. To use the ARC function, connect to the
ARC compatible HDMI jack of the TV and make
appropriate settings on this unit. See "3 HDMI Setup"
of "Step 2: Setting Up".
DIGITAL
OPTICAL
OUT
AUDIO
OUT
TV
¼ Audio connection with a TV not supporting ARC
¼ Select an appropriate
connection for your TV.
HT-R494_BAS_En_SN29401998_1503xx.indd 5 2015/03/12 15:07:42
Step 1: Connections
En-6
2 Connecting the AM/FM Antenna
Connect the antennas to listen to AM/FM broadcast. When
listening to the broadcast for the first time, adjust the
antenna position and orientation to get the best reception.
AM loop antenna
(supplied)
Indoor FM antenna
(supplied)
Fix with a tack on
the wall.
(North American models) (European, Australian
and Asian models)
Assemble the AM loop antenna (supplied).
Connection with a player that has a HDMI jack
Connect to the "BD/DVD", "CBL/SAT", "GAME 1", and
"STRM BOX" jacks using a HDMI cable. Connect the
equipment to the corresponding jack, for example a Blu-ray
Disc Player to "BD/DVD", so that it is easy for you when
selecting with the input selector. Connect a Streaming
Media Player to the "STRM BOX" jack. When a power
supply is required, connect using a USB cable to the
POWER OUT port. ()
¼ The POWER OUT jack supports a 5V/1A power supply.
Connection with a player that does not have a
HDMI jack
Connect equipment with video output jacks to the "BD/
DVD", "CBL/SAT", "GAME 2", and "VCR" jacks. Connect
with component video cable or composite video cable for
video signals and digital coaxial cable or RCA cable for
audio signals.
Connect audio equipment such as a CD Player using a
digital optical cable or an RCA cable to the "CD" jack.
● Video signals input to the component video input or
the composite video input will be upconverted to HDMI
signals and then output from the "to TV" jack. When
upconverting video signals input to the component video
input for output from the HDMI OUT jack, set the output
resolution of the player to 480i or 576i. If the input has
480p/576p or higher resolution, a message prompting
you to change the resolution setting will appear. If your
player does not support 480i or 576i output, use the
composite video jack.
● Connection with a digital coaxial cable or digital optical
cable is necessary for playback of digital surround
sources such as Dolby Digital. The digital in optical jack
of the unit has a cover, push in the cable against the
cover as it is turned inside.
HT-R494_BAS_En_SN29401998_1503xx.indd 6 2015/03/12 15:07:42
Step 1: Connections
En-7
HEIGHT RIGHT
FRONT RIGHT
HEIGHT LEFT
FRONT LEFT
LINE INPUT
1/2˝-5/8˝
(12-15 mm)
3/8˝-1/2˝
(10-12 mm)
#)
Front & Height R
&
Surround R
%
Surround L
"(
Front & Height L
$
Center
'
Subwoofer with
built-in power
amplifier
3 Connecting Speakers
Speaker layout
(
$
%
&
'
)
"
#
" #
Front speakers
$
Center speaker
% &
Surround speakers
'
Subwoofer
( )
Height speakers
Front & Height speakers "# & () placed with their top
diaphragms facing toward the ceiling can produce a sound
field of the Dolby Atmos listening mode by providing sounds
echoing off the ceiling. The speakers on the front output
front stereo sound.
$ outputs center sounds such as dialogs and vocals.
%& create back sound field. ' reproduces bass sounds
and creates rich sound field.
● To enjoy the Dolby Atmos listening mode, the Dolby
Atmos format signals need to be input from a player.
HT-R494_BAS_En_SN29401998_1503xx.indd 7 2015/03/12 15:07:42
Step 1: Connections
En-8
Instructions on how to connect speakers
2 speaker cables are required to connect each Front
& Height speaker. Use one speaker cable for the other
speakers' connection.
Cut and remove the plastic coating from the end of the
speaker cable, twist the core and connect it to the terminal.
Be sure to make correct connection between the unit's
jacks and speaker's jacks (+ to + and - to -) for each
channel. If connection is wrong, a bass sound may become
poor due to reverse phase.
● Short-circuiting the + cable and - cable or contacting
the cable core to the rear panel of the unit may cause
failure. Further, do not connect more than 2 speaker
cables to each individual set of speaker terminals on
this unit or the speakers.
When using commercially available banana plugs:
tighten the speaker terminals to the end and then insert
the banana plugs. Do not insert the core of speaker cable
directly into the hole for banana plug of speaker terminal.
(North American models)
HT-R494_BAS_En_SN29401998_1503xx.indd 8 2015/03/12 15:07:43
Step 2: Setting Up
En-9
Operation: Use the remote controller of this unit to
operate the menus shown on the TV screen. To display the
guidance, you need to make HDMI connection between
the unit and TV. Select the item with the cursor buttons of
the remote controller and press ENTER to confirm your
selection. To return to the previous screen, press RETURN.
1 Turning the Power On
Connect the power cord to the outlet. Press z ON/
STANDBY on the main unit or z RECEIVER on the remote
controller to turn the unit on or to standby mode.
● When the unit is turned on, a large instantaneous
current may flow affecting functionality of the computer
and other devices. It is recommended to use a separate
outlet from that for the computer or such other sensitive
devices.
2 Making Automatic Speaker Setting
The AccuEQ Room Calibration function, our proprietary
technology, measures the test tone coming from each
speaker with the supplied speaker setup microphone,
setting of the number of speakers, volume level, each
speaker's optimum crossover frequencies, and distance
from the primary listening position, and also enables
correction of distortion caused by the acoustic environment
of the room.
● You cannot return to the previous screen during speaker
setup, even if you press RETURN.
1� Place the speaker setup microphone�
Before starting the procedure, refer to the figure and
place the supplied speaker setup microphone at the
measurement position .
Listening area
Measurement position with
microphone
¼ Correct measurement will not be possible if the microphone is held
by hand. Measurement is not possible if headphones are being used.
¼ The subwoofer sound may not be detected since it is extremely
low frequencies. Set the subwoofer volume to around the half of its
maximum volume and make its frequency to the maximum level.
¼ Measurement may be interrupted if there is ambient noise or radio
frequency interference. Close the window and turn off the home
appliance and fluorescent light.
2� Connect the speaker setup microphone to the
SETUP MIC jack of the unit�
SETUP MIC jack
Speaker
setup
microphone
HT-R494_BAS_En_SN29401998_1503xx.indd 9 2015/03/12 15:07:43
Step 2: Setting Up
En-10
When the screen below is displayed, press ENTER on the
remote controller without changing any of the settings.
AccuEQ Room Calibration
Select how many speakers you have.
Ne xt
ENTER
Speaker Channels
Subwoofer
Height Speaker
5.1.2 ch
Yes
Bundled Dolby Speaker
After that, follow the guidance displayed on the TV
screen to operate the unit. To proceed to the next
screen, press ENTER on the remote controller.
3� The test tones sound from the connected speakers
and automatic speaker setting starts�
Measurement will be made three times or more for each
speaker. It takes several minutes to be completed. Keep
the room as quiet as possible during measurement. If
any of the speakers do not produce the test tone, check
for disconnection.
● During measurement, each speaker outputs the test
tones at a high volume. Be careful of sound leak
that may disturb your neighbors, or be careful not to
frighten young children.
● To cancel measurement on the way, disconnect the
microphone plug.
4� When the measurement is completed, the
measurement result is displayed�
Press
t
/
u
on the remote controller to check the
settings. Press ENTER with "Save" selected. Select
"On" in the next screen and press ENTER on the remote
controller.
● You should normally select "On (All Channels)", and
to disable just the front speakers, you should select
"On (Except Front Left/Right)".
● If there is an error message, follow the on-screen
instruction to remove the error cause.
5� When "Please unplug setup microphone�" is
displayed, disconnect the microphone�
3 HDMI Setup
The unit supports the linked system function such as power
on/off link when connected via HDMI cable with a CEC
(Consumer Electronics Control) compliant TV or player. You
need to change the default setting to use the linked system
function, HDMI Standby Through function and ARC (Audio
Return Channel) function.
HDMI CEC (RIHD)
¼ RIHD is a name for the linked system function of Onkyo's CEC compliant
products.
The following linked operations are possible with connected
equipment when the CEC function is enabled.
●
Turning the TV to standby mode will turn the unit to
standby mode.
●
On the TV side, it is possible to set whether to output
audio from the speakers connected to the unit or from the
TV's speakers.
●
Starting playback of a CEC compliant player/recorder will
automatically switch the unit's input to the HDMI input of
the player/recorder. If the unit is in standby mode, it will
automatically be turned on.
1� After pressing RECEIVER, press SETUP on the
remote controller�
2� Select "5� Hardware" with the cursor and press
ENTER�
3� Select "HDMI" with the cursor and press ENTER�
4� Select "HDMI CEC (RIHD)" with the cursor and
select "On"�
When setting is complete, press SETUP to close the
menu screen.
● It is also possible to control the connected CEC
compliant equipment with the remote controller of the
unit. For details, see the Advanced Manual.
HDMI Standby Through
The function allows transmission from players to the TV
even if the unit is in standby. Setting the HDMI CEC (RIHD)
setting mentioned above to "On" enables this setting
automatically.
● Power consumption in standby mode increases when
the HDMI Standby Through function is enabled.
ARC (Audio Return Channel)
Simple connection to the ARC compatible TV using a single
HDMI cable allows to listen to the TV audio signals from
the speakers connected to the unit. Setting the HDMI CEC
(RIHD) setting mentioned above to "On" enables the "Audio
Return Channel" setting automatically.
Audio output of connected players
To enjoy digital surround sound including Dolby
Digital and DTS, audio output should be set to
"Bitstream output" on the connected Blu-ray Disc
Player or other device.
Depending on the settings on the Blu-ray Disc Player,
there may be cases when Dolby TrueHD, Dolby
Atmos, and DTS-HD Master Audio is not output
according to the format of the source.
In this case, in the Blu-ray Disc Player settings
try setting "BD video supplementary sound" (or
secondary sound) to "Off".
Change the listening mode after changing the setting
to confirm.
HT-R494_BAS_En_SN29401998_1503xx.indd 10 2015/03/12 15:07:44
Step 3: Playing Back
En-11
1 Basic Operations
When using the remote controller to operate
the AV receiver: The remote controller of this unit
has the remote mode function for controlling other
devices. You cannot control this unit when the
remote controller is in the remote mode other than
RECEIVER mode (for controlling this unit). Be sure
to press F RECEIVER to select the RECEIVER
mode before starting operation.
1� Turning the power on�
Press 1 z RECEIVER on the remote controller to turn
the power on.
● Switch the input on the TV to that assigned to the
unit. Use the TV's remote controller.
2� Select the input on the unit�
Press the 2 INPUT SELECTOR for the player you want
to listen to. Press TV to listen to the TV's sound. You can
also use the input selector buttons on the main unit.
● Input will automatically be selected if the TV or player
is CEC compliant and connected to the unit with
HDMI cable.
3� Select the desired listening mode�
After pressing F RECEIVER, press the 7 listening
mode buttons to switch the mode so that you can enjoy
different listening modes.
4� Adjust the volume with H VOL�
Part names and functions of the remote
controller
1
3
7
5
6
8
2
4
I
H
J
K
9
G
F
1 z RECEIVER button: Turns the unit on or into standby
mode.
2 REMOTE MODE/INPUT SELECTOR buttons: Switch
the input to be played. Furthermore, by registering a
particular remote control code to a button, you can
switch the remote control mode to operate other
equipment by pressing that button.
3 MEMORY button: Registers a radio station.
4 TUN MODE button: Switches the tuning mode.
5 Cursor buttons and ENTER button: Move the cursor
and confirms the selection.
6 SETUP button: Displays the screen for making various
settings for this unit.
7 Listening mode buttons: Allow you to select the
listening mode.
MOVIE/TV button: You can select a listening mode
suitable for movies and TV programs.
MUSIC button: You can select a listening mode suitable
for music.
GAME button: You can select a listening mode suitable
for games.
STEREO button: You can select a listening mode for
stereo and all channel stereo sources.
● For details on the listening modes, see the Advanced
Manual.
8 DIMMER button: Switches the brightness of the display.
9 MUSIC OPT button: Turns on/off the MUSIC
OPTIMIZER function that improves the quality of the
compressed audio.
F RECEIVER button: Switches the remote controller to
the mode for operating this unit.
G MUTING button: Temporarily mutes audio. Press again
to cancel muting.
H VOLUME buttons: Allow you to adjust the volume. This
button also cancels the muting.
I RETURN button: Returns the display to the previous
state.
J Q button: Displays the Quick Setup menu that allows
you to quickly access the frequently used setting items
including sound quality adjustment.
K DISPLAY button: Switches the information on the
display.
HT-R494_BAS_En_SN29401998_1503xx.indd 11 2015/03/12 15:07:44
Step 3: Playing Back
En-12
Display
13 52 64
87
1 Lights in the following conditions. "HDMI": HDMI signals
are input and HDMI input selector is selected. This
lights faintly when the HDMI Standby Through function
is enabled and the unit is in standby. / "ARC": Audio
signals are input from ARC compatible TV and TV
input selector is selected. / "3D": Input signals are 3D. /
"DIGITAL": Digital signals are input and selected.
2 Stays lit when headphones are connected.
3 Lights according to the type of input digital signals and
the listening mode.
4 Stays lit when Music Optimizer is enabled.
5 Lights in the following conditions. "AUTO": Tuning mode
is auto. / "TUNED": Receiving AM/FM radio. 
flashes while tuning is automatically performed. / "FM
STEREO": Receiving FM stereo. / "RDS" (European,
Australian and Asian models): Receiving RDS
broadcasting.
6 "MUTING": Flashes when muting is on.
7 Lights in the following conditions. "SLEEP": Sleep timer
has been set. This lights faintly when the Power Out
at Standby for STRM BOX function is enabled and the
unit is in standby. / "ASb" (Auto Standby): Auto Standby
is on. / "ch": Channel is being set. / "Hz": Crossover
frequencies are being set. / "m/ft": Speaker distances
are being set. / "dB": Speaker volume is being set.
8 Displays various information of the input signals.
Pressing DISPLAY displays the type of input digital
signals and the listening mode.
2 Bluetooth
®
 
You can wirelessly enjoy music files stored in a smartphone
or other Bluetooth-enabled device. The coverage area is 48
feet (15 meters).
● The Bluetooth-enabled device needs to support the
A2DP profile.
● Note that connection is not always guaranteed with all
Bluetooth-enabled devices.
Pairing
Pairing is necessary when connecting the Bluetooth-
enabled device for the first time. Before starting the
procedure, learn how to enable the Bluetooth setting
function and to connect with other devices on the
Bluetooth-enabled device.
1� Press BLUETOOTH on the remote controller�
The unit begins pairing and "Now Pairing..." is displayed.
2� While "Now Pairing���" is on the display, complete
connection on the Bluetooth-enabled device in the
nearby area within about 1 minute�
If the name of this unit is displayed on the Bluetooth-
enabled device's display, select this unit. Pairing will end
after a short time.
● If a password is requested, enter "0000".
● You can pair with another Bluetooth-enabled device
by pressing and holding the BLUETOOTH button
until "Now Pairing..." is on the display. This unit can
store the data of up to 8 paired devices.
Playing Bluetooth-enabled devices
If the unit is on and the Bluetooth-enabled device is
connected, the input will be automatically switched to
BLUETOOTH. Play music in this state.
For details on using the remote controller for these
operations, see the Advanced Manual.
● If the volume setting on the Bluetooth-enabled device is
low, the sound will not be output from this unit.
● Due to the characteristics of Bluetooth wireless
technology, the sound produced on this unit may slightly
be behind the sound played on the Bluetooth-enabled
device.
● The on-screen displays are not displayed when the
OSD language is set to Chinese. (European, Australian
and Asian models)
3 AM/FM Radio
The Basic Manual explains the method using automatic
tuning. For manual tuning, see the Advanced Manual.
1� Press TUNER on the remote controller several times
to select either "AM" or "FM"�
2� Press TUN MODE so that the "AUTO" indicator on
the display lights�
3� Press the
/
cursor buttons�
The automatic tuning to a radio station starts. Searching
stops when one is tuned. When tuned into a radio
station, the "
u
TUNED
t
" indicator on the display lights.
The "FM STEREO" indicator lights if the radio station is
an FM radio station.
● Alternatively you can press
TUNING
on the main
unit.
Actual display varies
depending on the country
or the region
TUNED
FM STEREO
AUTO
Registering a radio station: You can register up to 40 of
your favorite AM/FM radio stations.
1. Tune into the AM/FM radio station you want to register.
2. Press MEMORY on the remote controller so that the
preset number on the display flashes.
3. Press CH +/- several times to select a number between
1 and 40 while the preset number is flashing (about 8
seconds).
● Alternatively you can press
t
PRESET
u
on the main
unit.
4. Press MEMORY again to register the station.
When registered, the preset number stops flashing. To
select a preset radio station, press
t
PRESET
u
on the
HT-R494_BAS_En_SN29401998_1503xx.indd 12 2015/03/12 15:07:44
Step 3: Playing Back
En-13
main unit or CH +/− on the remote controller.
● To delete a preset station, after selecting the preset
station you want to delete, press MEMORY on the
remote controller, and with the preset number flashing
on the display, press CLR on the remote controller.
AM/FM frequency step setting
It may be necessary for you to change the
frequency step to tune the radio in your area.
Change the step with the following procedure. Note
that when this setting is changed, all radio presets
are deleted.
1 After pressing
RECEIVER on the remote
controller, press SETUP.
2. Select "5. Hardware" with the cursor and press
ENTER.
3. Select "Tuner" with the cursor and press ENTER.
4. Select "AM / FM Frequency Step" (North
American models) or "AM Frequency Step"
(European, Australian and Asian models) with
the cursor and select the frequency step for your
area.
4 Quick Setup Menu
You can perform common settings on the TV screen while
playing.
1� Press Q on the remote controller�
The Quick Setup menu is displayed on the connected
TV's screen.
Quick Setup
Listening Mode
Audio
Information
MOVIE/TV
MUSIC
GAME
BD/DVD
2� Select the item with the cursors on the remote
controller and then press ENTER�
● To return to the previous screen, press RETURN.
3� Select the setting with the cursors of the remote
controller�
Listening Mode: Select the listening mode from the
categories of "MOVIE/TV", "MUSIC" and "GAME".
After selecting the Listening Mode, press ENTER button to
confirm.
● It cannot be set when audio is played from the TV's
speakers.
Audio: You can perform various audio settings including
audio quality and speaker level adjustment.
● You cannot select this item when audio is output from
the TV's speakers.
Bass, Treble: Adjust volume of the front speaker.
● It cannot be set if the listening mode is Direct.
Phase Matching Bass: Suppress phase shift in the
midrange to enhance bass sound. Thus smooth and
powerful bass sound can be obtained.
● It cannot be set if the listening mode is Direct.
Center Level, Subwoofer Level: Adjust the speaker
level while listening to the sound. The adjustment you
made will be reset to the previous status when you turn
the unit to standby mode.
● Changes may not be possible depending on the
speaker settings.
● This setting is not possible during MUTING or when
using headphones.
A/V Sync: If the video is behind the audio, you can
delay the audio to offset the gap. Different settings can
be set for each input selector.
● It cannot be set if the listening mode is Direct.
AccuEQ Room Calibration: Enable or disable the
settings made by automatic speaker setting. To enable
them, you should normally select "On (All Ch)", and to
disable just the front speakers, you should select "On
(ex. L/R)". The setting can be separately set to each
input selector.
● This setting cannot be selected if the automatic
speaker setting has not been performed.
● It cannot be set if headphones are connected or the
listening mode is Direct.
Music Optimizer: Improve the quality of the
compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The
setting can be separately set to each input selector.
● The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream
signals.
● It cannot be set if the listening mode is Direct.
Late Night: Make small sounds to be easily heard. It
is useful when you need to reduce the volume while
watching a movie late night. You can enjoy the effect
only with Dolby Digital, Dolby Digital Plus, and Dolby
TrueHD input sources.
● Turning the unit to standby mode will set the setting
to "Off". In case of Dolby TrueHD, the setting will be
set to "Auto".
● If "Loudness Management" is set to "Off", this
function is not available when playing Dolby Digital
Plus or Dolby TrueHD.
Cinema Filter: Adjust the soundtrack that was
processed to enhance its treble, in order to make it
suitable for home theater.
● This function can be used in the following listening
modes: Dolby Digital, Dolby Digital Plus, Dolby
TrueHD, Multichannel, DSD, DTS, DTS-ES, DTS
Neo:6 Cinema, DTS 96/24, DTS-HD High Resolution
Audio, DTS-HD Master Audio, DTS Express.
Center Spread: Adjust the width of the sound field of
the front channel when playing in the Dolby Surround
listening mode.
HT-R494_BAS_En_SN29401998_1503xx.indd 13 2015/03/12 15:07:45
Step 3: Playing Back
En-14
To spread the width of the sound field to the left and
right, set to "On". To concentrate sound in the center, set
to "Off".
● Depending on the speaker settings, this becomes
"Off".
Information:
Audio: Displays the audio input source, format, number
of channels, sampling frequency, listening mode, and
number of output channels.
Video: Displays information such as the video input
source, resolution, color space, color depth, 3D
information, Aspect and output.
Tuner: Displays information such as the band,
frequency, and preset number. This is displayed only
when "TUNER" is selected as the input source.
5 Other useful functions
To adjust the sound quality
It is possible to enhance or moderate the bass and treble
of front speakers. Press TONE on the main unit several
times to select the desired setting from "Bass", "Treble" and
"Phase Matching Bass", and adjust with +/-.
● It cannot be set if the listening mode is Direct.
"Bass": Allows you to enhance or moderate the bass.
"Treble": Allows you to enhance or moderate the treble.
"Phase Matching Bass": Allows you to keep the clear
midrange and effectively enhance the bass.
Checking the Input Format
Press DISPLAY on the remote controller several times to
switch the display of the main unit in order of:
Input source & volume
Listening mode
Signal format
Sampling frequency
Input signal resolution
● If "Dolby D 5.1" is displayed in Signal format, the
Dolby Digital 5.1 ch signals are being input. When
listening to AM/FM radio, the band, frequency and
preset number are displayed.
Playing Audio and Video from Separate Sources
It is possible to play audio and video from different sources.
For example, you can play audio from the CD player and
video from the BD/DVD player. In this case, press BD/
DVD and then CD. Then start playback on the BD/DVD
player and CD player. This function is effective when an
input with audio only has been selected (CD, TUNER or
BLUETOOTH). ()
¼ When BLUETOOTH is selected, press MODE on the remote controller.
HT-R494_BAS_En_SN29401998_1503xx.indd 14 2015/03/12 15:07:45
En-15
Others
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the
power on/off or disconnecting/connecting the
power cord, which is easier than working on the
connection, setting and operating procedure. Try
the simple measures on both the unit and the
connected device. If the problem is that the video
or audio is not output or the HDMI linked operation
does not work, disconnecting/connecting the HDMI
cable may solve it. When reconnecting, be careful
not to wind the HDMI cable since if wound the
HDMI cable may not fit well. After reconnecting, turn
off and on the unit and the connected device.
The AV receiver turns off unexpectedly�
● The AV receiver will automatically enter standby mode when
Auto Standby or Sleep Timer is set and launched.
● The protection circuit may have been activated. If this is the
case, when you turn the unit on again, "AMP Diag Mode" will
appear on the main unit’s display. The unit will then enter a
mode that detects abnormal conditions. If no problems are
detected, "AMP Diag Mode" will disappear and the unit will
return to a normal state. If "CHECK SP WIRE" appears on the
display, the speaker cables may be short-circuited. Turn the
unit off, and check to see if the cable core of any of the speaker
cables is in contact with that of another speaker cable or with
the rear panel. After that, turn the unit on again. If "NG" appears,
unplug the power cord immediately and contact your Onkyo
dealer.
There’s no sound, or it’s very quiet�
● A wrong input selector button has been selected. Select a
correct input for the player. Also check that muting is not on.
● Not all listening modes use all speakers.
There’s no picture�
● A wrong input selector button has been selected.
● To display video from the connected player on the TV screen
while the unit is in standby, you need to enable HDMI Standby
Through function.
● When the TV image is blurry or unclear, power cord or
connection cables of the unit may have interfered. In that case,
keep distance between TV antenna cable and cables of the unit.
Video and audio are out of synch�
● Video may be delayed relative to audio depending on the
settings and connections with your TV. Adjust in "Step 3:
Playing Back", "4 Quick Setup Menu", "A/V Sync".
Cannot play digital surround�
● To enjoy digital surround sound including Dolby Digital and
DTS, audio output should be set to "Bitstream output" on the
connected Blu-ray Disc Player or other device.
Cannot output audio such as Dolby Atmos according
to the format of the source�
● If you cannot output audio according to the format of the
source (Dolby TrueHD, Dolby Atmos, DTS-HD Master Audio,
etc.), in the Blu-ray Disc Player settings try setting "BD video
supplementary sound" (or secondary sound) to "Off". Change
the listening mode for each source after changing the setting to
confirm.
HDMI control does not function correctly�
● Set the CEC link function of the unit to on. It is also necessary
to make the HDMI linked system setting on the TV. See the TV's
instruction manual for details.
Resetting the unit
Resetting the unit to the status at the time of shipment may solve
the problem. If the measures above do not solve the problem, reset
the unit with the following procedure. If you reset the unit status,
your preferences will be reset to the defaults. Note them down
before starting reset.
How to reset:
1�
While holding down CBL/SAT on the main unit (note that
step 2 must be performed with this button pressed down)
2� Press zON/STANDBY on the main unit� ("Clear" appears on
the display and the unit returns to standby�)
● Do not unplug the power cord until "Clear" disappears from
the display.
Clear
1.
While holding
down CBL/SAT,
2.
Press zON/
STANDBY�
How to reset the remote controller:
1�
While holding down RECEIVER on the remote controller,
press Q until the remote indicator stays lit (about 3
seconds)�
2� Within 30 seconds, press RECEIVER again�
Remote indicator
RECEIVER
Q
HT-R494_BAS_En_SN29401998_1503xx.indd 15 2015/03/12 15:07:45
Others
En-16
Specifications
Amplifier Section
Rated Output Power (North American)
With 8 ohm loads, both channels driven, from 20-20,000 Hz; rated 65
watts per channel minimum RMS power, with no more than 0.7% total
harmonic distortion from 250 milliwatts to rated output.
Surround Mode Output Power ()
(6 ohms, 1 kHz THD 0.9%) 115 W per channel
¼ Reference output for each speakers.
Depending on the source and the listening mode settings, there may be
no sound output.
Rated Output Power (Others)
7 ch × 100 W at 6 ohms, 1 kHz, 1 ch driven of 1% (IEC)
Maximum Effective Output Power
7 ch × 120 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) (Asian)
Dynamic Power ()
¼ IEC60268-Short-term maximum output power
160 W (3 Ω, Front)
125 W (4 Ω, Front)
85 W (8 Ω, Front)
THD+N (Total Harmonic Distortion+Noise)
0.08% (20 Hz - 20 kHz, half power)
Input Sensitivity and Impedance (Unbalance)
200 mV/47 kΩ (LINE, 1 kHz 100 W/8 Ω)
Rated RCA Output Level and Impedance
1 V/470 Ω (SUBWOOFER PRE OUT)
Frequency Response
10 Hz - 100 kHz/+1 dB, –3 dB (Direct mode)
Tone Control Characteristics
±10 dB, 20 Hz (BASS)
±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio
100 dB (LINE, IHF-A)
Speaker Impedance
6 Ω - 16 Ω
Video Section
Signal level
1.0 Vp-p/75 Ω (Component Y)
0.7 Vp-p/75 Ω (Component Pb/Cb, Pr/Cr)
1.0 Vp-p/75 Ω (Composite)
Maximum resolution supported by component video
480i/576i
Tuner Section
FM Tuning Frequency Range
87.5 MHz - 107.9 MHz (North American)
87.5 MHz - 108.0 MHz, RDS (Others)
AM Tuning Frequency Range
522/530 kHz - 1611/1710 kHz
Preset Channel
40
Bluetooth Section
Communication system
Bluetooth Specification version 2.1 +EDR (Enhanced Data Rate)
Maximum communication range
Line of sight approx. 15 m ()
Frequency band
2.4 GHz band
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
A2DP 1.3 (Advanced Audio Distribution Profile)
AVRCP 1.5 (Audio Video Remote Control Profile)
Supported Codecs
SBC
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz)
¼ The actual range will vary depending on factors such as obstacles between
devices, magnetic fields around a microwave oven, static electricity,
cordless phone, reception sensitivity, antenna’s performance, operating
system, software application, etc.
General
Power Supply
AC 120 V, 60 Hz (North American)
AC 220 - 240 V, 50/60 Hz (Others)
Power Consumption
4.3 A (North American)
420 W (Others)
0.15 W (Stand-by, North American)
0.3 W (Stand-by, Others)
55 W (No-sound)
Dimensions (W × H × D)
435 mm × 160 mm × 328 mm
17-1/8" × 6-5/16" × 12-15/16"
Weight
7.8 kg (17.2 lbs.) (North American)
8.0 kg (17.6 lbs.) (Others)
● HDMI
Input
BD/DVD, CBL/SAT, GAME 1, STRM BOX
Output
HDMI OUT (to TV)
Video Resolution
4K 60 Hz (RGB/YCbCr 4:4:4/YCbCr 4:2:2, 24 bit)
Audio Format
Dolby Atmos, Dolby TrueHD, Dolby Digital Plus, Dolby Digital,
DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS 96/24,
DTS-ES, DTS, DTS Express, DSD, Multichannel PCM (up to 8ch)
Supported
3D, Audio Return Channel, Deep Color, x.v.Color™, LipSync, CEC, 4K,
Extended Colorimetry (sYCC601, Adobe RGB, Adobe YCC601),
Content Type, 3D Dual View, 21:9 Aspect Ratio Video Format
● Video Inputs
Component
COMPONENT VIDEO (BD/DVD, GAME 2)
Composite
VIDEO (CBL/SAT, VCR), AUX INPUT VIDEO (front)
● Audio Inputs
Digital
OPTICAL (CD, TV)
DIGITAL AUDIO (BD/DVD)
Analog
AUDIO (BD/DVD, CBL/SAT, GAME 2, VCR, CD, TV)
AUX INPUT (front)
● Audio Outputs
Analog
Pre Out (SUBWOOFER)
Speaker Outputs
FRONT L/R, CENTER, SURROUND L/R, HEIGHT/BACK L/R
Phones
PHONES (Front, ø 6.3)
● Others
Setup Mic 1 (Front)
RI REMOTE CONTROL 1
STRM BOX POWER OUT 1 (5 V/1 A)
Specifications and features are subject to change without notice.
HT-R494_BAS_En_SN29401998_1503xx.indd 16 2015/03/12 15:07:45
Others
En-17
Table of display resolutions
Refer to the following table for information about the image formats and resolutions output by this unit in
response to input signals.
Output
Input
HDMI
4K 1080p/24 1080p 1080i 720p 480p/576p 480i/576i
HDMI
4K
1080p/24
1080p
1080i
720p
480p/576p
480i/576i
Component
1080p
1080i
720p
480p/576p
480i/576i
Composite 480i/576i
Resolutions supported by HDMI
Input support
Content
protection
technology
Display
resolution
Frame rate Color space Color Depth Remarks
HDMI input
(BD/DVD,
CBL/SAT,
GAME1,
STRM BOX)
HDCP1.4
HDCP2.2
720×480i 60Hz
RGB/YCbCr4:4:4/
YCbCr4:2:2
8/10/12/16bit
With YCbCr4:2:2,
Color Depth
supported is 12 bit
only.
720×576i 50Hz
720×480p 60Hz
720×576p 50Hz
1920×1080i 50/60Hz
1280×720p 24/25/30/50/60Hz
1680×720p 24/25/30/50/60Hz
1920×1080p 24/25/30/50/60Hz
2560×1080p 24/25/30/50/60Hz
4K
(3840×2160p)
24/25/30Hz
RGB/YCbCr4:4:4 8/10/12/16bit
YCbCr4:2:2 12bit
50/60Hz
RGB/YCbCr4:4:4 8bit
YCbCr4:2:2 12bit
YCbCr4:2:0 8/10/12/16bit
4K SMPTE
(4096×2160p)
24/25/30Hz
RGB/YCbCr4:4:4 8/10/12/16bit
YCbCr4:2:2 12bit
50/60Hz
RGB/YCbCr4:4:4 8bit
YCbCr4:2:2 12bit
YCbCr4:2:0 8/10/12/16bit
HT-R494_BAS_En_SN29401998_1503xx.indd 17 2015/03/12 15:07:45
Others
En-18
Precautions
For European Models
Declaration of Conformity
We declare, under our sole responsibility, that
this product complies with the standards:
– Safety
– Limits and methods of measurement of
radio disturbance characteristics
– Limits for harmonic current emissions
– Limitation of voltage changes, voltage
fluctuations and flicker
– RoHS Directive, 2011/65/EU
– Hereby, Onkyo Corporation, declares that this HT-R494 is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/EC.
– С настоящето, Onkyo Corporation, декларира, че HT-R494 е в
съответствие със съществените изисквания и другитеприложими
разпоредби на Директива 1999/5/EC.
– Onkyo Corporation tímto prohlašuje, že HT-R494 splňuje základní
požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.
– Undertegnede Onkyo Corporation erklærer herved, at følgende udstyr
HT-R494 overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
– Hiermit erklärt Onkyo Corporation, dass sich das Gerät HT-R494 in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
– Käesolevaga kinnitab Onkyo Corporation seadme HT-R494 vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
– ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo Corporation ΔΗΛΩΝΕΙ
ΟΤΙ HT-R494 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ
ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
– Por la presente, Onkyo Corporation, declara que este HT-R494 cumple
con los requisitos esenciales y otras exigencias relevantes de la Directiva
1999/5/EC.
– Par la présente, Onkyo Corporation déclare que l’appareil HT-R494 est
conforme aux exigences essentielles et aux autres dispositions pertinentes
de la directive 1999/5/CE.
– Con la presente Onkyo Corporation dichiara che questo HT-R494 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
– Ar šo Onkyo Corporation deklarē, ka HT-R494 atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
– Šiuo Onkyo Corporation deklaruoja, kad šis HT-R494 atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
– A Onkyo Corporation ezzennel kijelenti, hogy a HT-R494 típusú beren-
dezés teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.
– Hierbij verklaart Onkyo Corporation dat het toestel l HT-R494 in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
– Niniejszym Onkyo Corporation deklaruje że HT-R494 jest zgodny z
zasadniczymi wymaganiami i innymi właściwymi postanowieniami
Dyrektywy 1999/5/EC.
– Eu, Onkyo Corporation, declaro que o HT-R494 cumpre os requisitos
essenciais e outras provisões relevantes da Directiva 1999/5/EC.
– Prin prezenta, Onkyo Corporation, declară că aparatul HT-R494 este
în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale
Directivei 1999/5/CE.
– Onkyo Corporation týmto vyhlasuje, že HT-R494 a spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
– Onkyo Corporation izjavlja, da je ta HT-R494 v skladu z bistvenimi
zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
– Onkyo Corporation vakuuttaa täten että HT-R494 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
– Härmed förklarar Onkyo Corporation att denna HT-R494 följer de
väsentliga kraven och andra relevanta stadgar i Direktiv 1999/5/EC.
– Hér með lýsir Onkyo Corporation því yfir að varan HT-R494 er í samræmi
við grunnkröfur og aðrar kröfur sem gerðar eru í tilskipun 1999/5/EC.
– Onkyo Corporation erklærer herved at denne HT-R494 er i
overensstemmelse med vesentlige krav og andre relevante bestemmelser
i direktiv 1999/5/EC.
– Ovime Onkyo Corporation, potvrđuje da je HT-R494 u suglasnosti sa
osnovnim zahtjevima i ostalim relevantnim odredbama Direktive 1999/5/
EC.
License and Trademark Information
Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos,
Dolby Surround, and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under license from
DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, the DTS-HD
logo, and DTS-HD Master Audio are registered trademarks or trademarks of
DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights
Reserved.
"CINEMA FILTER" and "CINEMA FILTER (logo)" are trademarks of Onkyo
Corporation.
®
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
The Bluetooth
®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Onkyo is under license.
Other trademarks and trade names are those of their respective owners.
Onkyo does not guarantee Bluetooth compatibility between the AV receiver and
all Bluetooth-enabled devices.
For compatibility between the AV receiver and another device with Bluetooth
technology, consult the device’s documentation and dealer. In some countries,
there may be restrictions on using Bluetooth devices. Check with your local
authorities.
Apple, Apple TV, iPod and iPhone are trademarks of Apple Inc., registered in
the U.S. and other countries.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
"x.v.Color" and "x.v.Color" logo are trademarks of Sony Corporation.
DSD and the Direct Stream Digital logo are trademarks of Sony Corporation.
AccuEQ, Music Optimizer, RIHD and WRAT are trademarks of Onkyo
Corporation.
"All other trademarks are the property of their respective owners."
HT-R494_BAS_En_SN29401998_1503xx.indd 18 2015/03/12 15:07:46
Page is loading ...
* 2 9 4 0 1 9 9 8 *
F1503-0
SN 29401998
(C) Cop
yright 2015 Onkyo Corporation Japan. All rights reserved.
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku,
OSAKA 541-0041, JAPAN
http://www.onkyo.com/
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
http://www.us.onkyo.com/
For Product Support Team Only:
1-800-229-1687
http://www.us.onkyo.com/
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
http://www.eu.onkyo.com/
Unit 1033, 10/F, Star House, No 3, Salisbury Road,
Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.hk.onkyo.com/
1301, 555 Tower, No.555 West NanJing Road, Jing’an District,
Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
http://www.cn.onkyo.com/
The Americas
China
Europe
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo
SUPPORT site.
http://www.intl.onkyo.com/support/
The above-mentioned information is subject to change
without prior notice.
Visit the Onkyo web site for the latest update.
(Mainland)
(Hong Kong)
Meridien House, Ground floor, 69 - 71 Clarendon Road,
Watford, Hertfordshire, WD17 1DS, United Kingdom
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
Supplied Accessories
Indoor FM antenna --- (1)
AM loop antenna --- (1)
Remote controller (RC-897M) --- (1)
Batteries (AA/R6) --- (2)
Speaker setup microphone --- (1)
¼ The number in parenthesis indicates the quantity. On packaging, the
letter at the end of the product name indicates the color.
How to use the remote controller
Batteries (AA/R6)
Remote control sensor
Approx.
16 ft. (5 m)
AV Receiver
¼ If you do not use the remote controller for a long time, remove the
batteries to prevent leakage.
¼ Note that keeping consumed batteries inside may cause corrosion
resulting in damage of the remote controller.
HT-R494_BAS_En_SN29401998_1503xx.indd 20 2015/03/12 15:07:47
/