Briggs & Stratton 020514-00 Owner's manual

Brand: Briggs & Stratton

Model: 020514-00

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Brute

Pressure

rator's

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association

(PWMA) standard PWI01 (Testing and Rating Performance of PressureWashers).

BRIGGS& STRATTONPOWERPRODUCTSGROUP,LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 315996G3 Revision -

Thankyou for purchasing this quality-built Briggs & Stratton@ pressurewasher. We are pleasedthatyou've placedyour

confidence in the BRUTFMbrand. When operatedandmaintained accordingto the instructions inthis manual,your Briggs &

Stratton pressurewasher will provide many years of dependableservice.

This manual contains safety information to makeyou awareof the hazardsand risks associatedwith pressure washersand

how to avoidthem. BecauseBriggs & Stratton does not necessarilyknow all the applicationsthis pressure washer could be

usedfor, it is important that you readand understand these instructions thoroughly before attempting to start or operatethis

equipment. Savethese original instructionsfar future reference.

This pressure washer requiresfinal assembly before use. Referto the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

You never haveto look far to find Briggs & Stratton support and servicefor your pressure washer.Consult your Yellow Pages.

Thereareover 30,000 Briggs & Stratton authorized servicedealersworldwide who provide qualityservice. You canalso

contact Briggs & Stratton Customer Serviceby phone at (800) 743o4115,or on the Internet at BRIGGSandSTRATTON.COM.

Forenginerelatedquestions,callAmerican HondaMotor Company, inc. at (888) 426o7701or visit www.handa-engines.cam

for a dealerIocator.

Pressure Washer

Model Number

Revision

Serial Number

Date Purchased

BRUTFMis a trademark

of Briggs & Stratton Power Products, LLC

Milwaukee, Wl, USA

2 www.brutepawer.cam

Table of Contents

Assembly ..................................... 7

Unpack PressureWasher....................................... 7

Attach HandleandAccessoryTray ............................... 7

Add Engine Oil and Fuel........................................ 8

Lubricate O-Rings ............................................ 8

Connect Hoseand Water Supply to Pump.......................... 9

Operation .................................... 11

PressureWasher Location..................................... 11

How to Start Your PressureWasher ............................. 11

How to Stop Your PressureWasher ............................. 12

How to UseAccessory Tray.................................... 12

How to UseSprayTips ....................................... 13

Applying Detergent .......................................... 13

PressureWasher Rinsing ..................................... 14

CleaningDetergentSiphoning Tube.............................. 14

Automatic Cool Down System IThermal ReHefl..................... 14

Maintenance .................................. 1,5

PressureWasher Maintenance ................................ 15

Engine Maintenance.......................................... 17

After EachUse.............................................. 17

Winter Storage.............................................. 18

Long Term Storage .......................................... 18

Warranty ..................................... 20

PressureWasher OwnerWarranty............................... 20

Specifications ................................. 22

Product Specifications........................................ 22

Common Service Parts ....................................... 22

Espafiol

OperatorSafety

Equipment Description

Read this ITlanuaJ carefuJJy and became familiar

with yourpressurewasher. Knowitsapplications,

its Jinlitatians,and any hazardsiflvaJved.

This pressurewasher operatesat a max of 2,600 PSi

(179.2 BARS)and a flow rateof up to 2.3 gallons per minute

(8.7 liters per minute). This high quality residentialsystem

features 10" (25.4 cm) wheels,axial cam pump with

stainless steel pistons, automatic cool down system,

detergent siphoning system, nozzleextension with quick

connect fitting, a variety of spray tips, heavyduty 25' (7.6 m)

hose, and more.

Everyeffort has beenmadeto ensurethat information in this

manual is accurateandcurrent. However,we reservethe

right to change,alter, or otherwise improve the product and

this document at anytime without prior notice.

The EmissionControl System for this pressurewasher is

warranted for standards set by the Environmental Protection

Agency andthe CaliforniaAir ResourcesBoard.

Mmportant Safety Mnformation

SafetySymbaisandMeanings

Operator'sManual

SlipperySurface

Toxic Fumes

ElectricalShock

Fall

Explosion

Fluid injection

Fire Kickback Projectile

Moving Parts Flying Objects ChemicalBurn Hot Surface

A Thesafetyalert symbol indicatesa potential personal

injury hazard.A signal word (DANGER,WARNING,or

CAUTION)is usedwith the alert symbol to designateadegree

or levelof hazardseriousness. A safety symbol may be used

to representthe type of hazard.Thesignal word NOT/CEis

usedto addresspractices not relatedto personalinjury.

A DANGERindicatesa hazardwhich, if not avoided, wiii

result in deathor serious injury.

_]_WARNENGindicatesa hazardwhich, if not avoided,

couid result in death or serious injury.

A CAUTJ0Nindicates ahazardwhich, if not avoided, cou/d

result in minor or moderate injury.

NOTICEaddress practices not relatedto personal injury.

A WARNING Theengine exhaustfrom this product

contains chemicals known to the Stateof Californiato

cause cancer,birth defects,or other reproductive harm.

A WARNING This product contains leadand lead

compounds, known to the State of Californiato cause

birth defects or other reproductive harm. V@shyour

hands after handling t,_£ product.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

Some chemicals or detergents could be harmful if inhaled

or ingested, resulting in death, serious injury, nausea,

fainting or poisoning.

* Operatethis product ONLYoutdoors.

* Keepexhaustgas from entering a confinedareathrough

windows, doors,ventilation intakes,or other openings.

* DO NOToperatethis product insideany building, carport,

porch, mobile equipment, marineapplications, or enclosure,

evenif windows and doors areopen.

* Use a respirator or maskwheneverthere is a chancethat

vapors may beinhaled when using chemicals.

* Readall instructions with mask so you arecertain the mask will

provide the necessary protection against inhaling harmful

vapors when using chemicals.

A WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

, DO NOTtouch hot parts andAVOID hot exhaust gases.

* Allow equipmentto cool beforetouching.

* Keepat least5 feet (1.5 m) of clearanceon all sidesof pressure

washer including overhead.

* It is aviolation of California Public Resource Code, Section

4442, to use or operate the engineon anyforest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained ineffective working order. Other states or

federal jurisdictions may have similar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designedfor the exhaust system

installed on this engine.

* Replacement parts must bethe sameand installed inthe Same

position as the original parts.

A WARNING Riskof electrocution.

Contactwith power source could causeelectric

shock or burn resulting in deathor serious injury.

,, NEVERspray near power source.

A WARNING Use of pressure washer could create

puddles and slippery surfaces causing

"t.. youto oso,tin0in so ioos

Injury.

Kickback from spray gun could cause you to fall resulting

in death or serious injury.

, Operatepressurewasher from a stable surface.

* Thecleaning areashould have adequateslopes and drainageto

reducethe possibility of a fall due to slippery surfaces.

* Beextremely careful if you must usethe pressurewasher from

a ladder,scaffolding, or any other similar location.

* Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A WARNING Fueland its vapors are extremely flammable

and explosive which could cause burns,

fire or explosion resulting in death,

serious injury and/or property damage.

WHENADDING OR DRNNING FUEL

. Turn pressurewasher engineOFFand let it cool at least 2

minutes before removingfuel cap. Loosen cap slowly to relieve

pressure in tank.

* Fill or drain fuel tank outdoors.

* DONOToverfill tank. Allow spacefor fuel expansion.

* If fuel spills, wait until it evaporatesbeforestarting engine.

* Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

* Checkfuel lines,tank, cap andfittings frequently for cracks or

leaks. Replaceif necessary.

* DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

* Ensurespark plug, muffler,fuel cap,and air cleanerarein place.

* DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

* DO NOToperatethis product inside any building, carport,

porch, mobile equipment, marineapplications, or enclosure.

DONOTtip engine or equipment at anglewhich causes fuel to

spill.

, DONOTsprayflammabb liquids.

WHENTRANSPORTBNG,MOVING OR REPAIMNG EQUIPMENT

* Transportimovdrepair with fuel tank EMPTYor with fuel shutoff

valveOFF.

* DONOTtip engine or equipmentat anglewhich causes fuel to

spill.

o Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELiN TANK

Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat havepilot light or other ignition

source becausethey could ignite fuel vapors.

,a, WARNING Starter cord kickback (rapid retraction) will

_, pull hand and arm toward engine faster than you

can let go which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

. NEVERpull starter cord without first relieving spraygun

pressure.

* When starting engine, pull cord slowly until resistance isfelt

andthen pull rapidlyto avoid kickback.

* After eachstarting attempt, where enginefails to run, always

point spray gun in safedirection, pressred button and squeeze

spray gun trigger to releasehigh pressure.

* Firmly grasp spray gun with both handswhen using high

pressure sprayto avoid injury when spraygun kicks back.

,a, WARNING ChemicalBurn Hazard.

Chemicals could cause burns resulting in death,

serious injury, and/or property damage.

* DO NOTuse caustic liquid with pressure washer.

* Use ONLYpressurewasher safe detergents/soaps. Followall

manufacturers instructions.

WARNING The high pressure stream of water that

_, his equipment produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which could result in

serious injury.

. if cut byfluid, call physicianimmediately. DONOTtreat as a

simple cut.

* DONOTallow CHILDRENto operate pressure washer.

* NEVERrepairhigh pressure hose.Replaceit.

* NEVERrepairleakingconnections with sealantof any kind.

Replaceo-ring or seal.

* NEVERconnect high pressure hoseto nozzleextension.

* Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

* ALWAYS pointspray gun in safedirection, pressred button

andsqueezespray gun trigger to releasehigh pressure, every

time you stop engine.

* NEVERaim spray gun at people,animals, or plants.

* DO NOTsecure spraygun in open position.

* DO NOTleavespray gun unattendedwhile machine is running.

* NEVERuseaspray gun which does not have atrigger lock or

trigger guard in placeand in working order.

* Always be certain spray gun, nozzlesand accessoriesare

correctly attached.

A WARNING Unintentionalsparking could causefire or

electric shock resulting n death or

serious injury.

WRENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

* Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug_

WHENTESTINGFORENGINESPARK

Use approved spark plug tester.

, DONOTcheckfor sparkwith spark plug removed.

A WARNING Starter and other rotating parts could

entangle hands, hair, clothing, or accessories

resulting in serious injury.

NEVERoperate pressure washerwithout protective housing or

covers.

° DO NOTwear looseclothing, jewelry or anything that could be

caught in the starter or other rotating parts.

° Tie up long hair and removejewdry.

,a, WARNING Riskof eyeor bodily injury.

Spraycould splash back or propel

objects resulting in serious injury.

* Alwayswear indirect vented (chemicalsplash) safetygoggles

markedto comply with ANSi Z8X1 when using or in vicinity of

this equipment.

* NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

* Alwayswear protectiveclothing such asa long-sleeved shirt,

long pantsand close-toed shoes.

* NEVERoperate pressure washerwhen barefoot or wearing

sandalsor shorts.

A CAUTION Excessively high operating speeds could

result in minor injury and/or pressure washer damage.

Excessively low speeds impose a heavy Ioa&

, DO NOTtamper with governor spring, links or other partsto

increase enginespeed. Pressurewasher suppliescorrect rated

pressure and flow when running at governed speed.

* DO NOTmodify pressurewasher in any way.

NOTICE High pressure spray could damagefragile items

including glass.....

DONOTpointspraygunatglasswhenusingred(0°) spraytip.

, NEVERaimspraygunatplants.

NOTICE mproper treatment of pressure washer could

damage it and shorten its life.

,, if you havequestions about intended use,ask dealeror contact

qualified servicecenter.

* NEVERoperate units with brokenor missing parts, or without

protective housing or covers.

* DO NOTby-pass any safetydevice on this machine.

* DONOTtamper with governedspee&

* DONOToperate pressurewasher above ratedpressure.

* DONOTmodify pressurewasher inany way.

* Beforestarting pressure washer in cold weather,check all parts of

the equipment to be sure ice has not formed there.

* NEVERmove machine by pulling on hoses.Use handleprovided

on uniL

* This equipment is designedto be usedwith Briggs & Stratton

Power Products authorizedparts ONLY.if equipment is used with

parts that DONOTcomply with minimum specifications,user

assumesall risks and liabilities.

Your pressure washer requires some assembly and is ready

for useafter it has beenproperly serviced with the

recommendedoil and fuek

if you haveanyproblems with the assemblyof your pressure

washer, pleasecall the pressurewasher helpline at

(800) 743-4115. if calling for assistance,pleasehavethe

model, revision, and serial number from the identification

label available,

UnpackPressureWasher

1, Removethe parts bag,accessories, and inserts

included with pressure washer.

2, OpencaCLoncompletely by cutting eachcorner from

top to bottom,

3, Ensureyou haveall included items priorto assembly,

items in the carton include:

o Main Unit

o Handle

o High Pressure Hose

o Spray Gun

o NozzleExtensionwith QuickConnectFitting

o Plastic AccessoryTray

o Oil Bottle

o Parts Bag(which includesthe following):

o Operator's Manual

o Owner's RegistrationCard

o Bagof 4 Multi-Colored Quick ConnectSpray Tips

o Handle/AccessoryTray FasteningHardwareKit

(which includes):

o CarriageBolts (2)

o Plastic Knobs (2)

o TreeClips (4)

To prepareyourpressurewasher for operation, youwiii

need to performthese tasks:

1, Fill out and send in registration card,

2. Attach handle and accessorytray to main uniL

3, Add oil to engine crankcase,

4, Add fuel to fuel tank,

5. Connecthigh pressure hoseto spray gun and pump,

6, Connectwater supply to pump,

7, Attach nozzleextensionto spray gun,

8, Select/attachquick connect spray tip to nozzle

extension,

Attach Handle and Accessory Tray

1, Placehandle(A) onto handlesupports (B) connectedto

main unit, Makesure hobs (C) in handle align with

hobs (C) on handlesupports,

insert handlecarriage bolts (D) through hobs from

inside of unit and attacha plastic knob (E) from outside

of unit, Tighten by hand, By loosening both knobs to

the middle section of the attachment bolt, the upper

handle canfold forward to store fiat atopthe cold

engine,

NOTICE DONOTfold handle down while the engine is hot.

3. Placeaccessorytray (F) over hobs (G) on handle

(viewing from back of unit), Pushthe tree clips (H) into

the hobs until they sit fiat against the accessorytray,

insert supplied accessoriesin spacesprovided in

accessorytray. SeeHow to UseAccessory Tray,

Add Engine Oil and Fuel

* Placepressure washer on a level surface.

NOTICE Any attempt to crank or start the engine before it

has been properlyfilled with the recommendedoil will

result in equipment failure.

• Referto enginemanualfor oilandfuelfill information.

• Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

* Referto engineoperator's manualandfollow oil and

fuel recommendations and instructions.

NOTfCE Checkoil oftenduring enginebreak-in. Referto

engine operator's manualfor recommendations.

Lubricate O-Rings

Lubrication of o-rings is extremely important for installation

and operation. The useof a lubricant (petroleum or synthetic

grease)during assembly helpsseat o-rings properly and

provides an improved seal. it also helps protect the o-ring

from damageby abrasion, pinching or cutting and extends

the life of the o-ring.

NOTfCE ALWAYSapplya small amountof lubricanton

o-rings prior to assemblingthe garden hoseto the pump (A),

high pressure hose(B), spray gun (C),and nozzle

extension(D).

Lubricateall cennectiens shewnbelew, feiiewing these

instru;tions:

1. Inspect and cleanconnecting surfaces prior to

lubrication and assembly.

2. Use lubricants sparingly during assembly; a light film is

all that is required.

3. Use a small brush or cotton swab to apply grease

directly to o-rings wherethey are not accessible(QC

fitting, M22 fitting).

8 www.brutepewer.eem

Connect Hose and Water Supply to Pump

NOTICE DONOTrun the pump without the water supply

connectedandturned on.

, Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

NOTICE Removeand discard the shipping capsfrom the

pump's high pressureoutlet andwater inlet before attaching

hoses.

1. Uncoil high pressure hoseand attachone end of hose

to baseof spray gun. Tighten by hand.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

NEVERconnecthighpressurehoseto nozzleextension.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

Alwaysbecertainspraygun,nozzlesandaccessoriesare .......

correctlyattached.

2. Attach other endof high pressure hoseto high

pressure outlet on pump. Tighten by hand.

Beforeconnecting garden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or

haveit replacedif damaged.DONOTrun pressure

washer if inlet screenis damaged.

4. Run water through your garden hosefor 30 secondsto

cleanout anydebris.

NOTICE DONOTsiphon standing waterfor the water

supply. UseONLYcold water (less than 100%).

NOTICE Using a OneWayValve (vacuum breakeror check

valve) at pump inlet could cause pump or inlet connector

damage.

ThereMUSTbeatleasttenfeetof unrestrictedgardenhose

betweenthepressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve.

* Damageto equipmentresulting from failure to follow this

instruction will void warranty.

5. Connectthe gardenhose (not to exceed50feet in

length) to the water inlet. Tighten by hand.

A WARNING Riskof eyeinjury.

Spray could splash back or propelobjects

resulting in serious injury.

* Alwayswear indirect vented (chemicalsplash) safetygoggles

markedto comply with ANSi Z87.1 when using or in vicinity of

this equipment.

* NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

6. Turn ONthe water, press red button (B) on the gun and

squeezethetrigger to purgethe pump system of air and

impurities.

Checklist Befere Starting Engine

Reviewthe unit's assembly to ensureyou haveperformed all

of the following.

1. Be sureto readthe OperatorSafetysection andHowto

Use Your Pressure Washerin Operationsection before

using pressurewasher.

2. Make sure handle is in placeand secure.

3. Checkthat oil hasbeenaddedto proper levelin the

engine crankcase.

4. Add proper fuel to fuel tank.

5. Checkfor properly tightened hoseconnections.

6. Checkto make surethere are no kinks,cuts, or damage

to high pressure hose.

7. Provide a proper water supply at an adequateflow.

Featuresand Controts

Readthis Operatar's Manual and safety rules before operating yaur pressurewasher.

Comparethe illustrations with your pressurewasher,to familiarizeyourself with the locations of various controls and

adjustments. Savethis manual for future reference.

A oSpray Tips -- Detergent,0°, 15° and 40°: for various

high pressure cleaningapplications.

B o Nigh Pressare Outlet -- Connectionfor high pressure

hose.

Co0il Fill/Dipstick -- Checkandadd engine oil here.

D oWater Inlet -- Connectionfor garden hose.

E oPump-- Developshigh pressure.

F oAutamatic Cad DawnSystem -- Cycleswater through

pump whenwater reaches125°-155°F (51°-68°C)_Warm

water will dischargefrom pump onto ground. This system

preventsinternal pump damage.

I_oDetergent Sipl_aningTube -- Useto siphon pressure

washer safe detergentsinto the low pressurestream.

N oAir Filter -- Protects engine by filtering dust and debris

out of intake air.

3 oRecall Starter -- Usedfor starling the enginemanually.

1(oFuel Tank-- Filltank with regular unleadedfuel. Always

leaveroom for fuel expansion.

IVlo NazzieExtensian with Quick Canned -- Allows you to

switch betweenfour different spray tips.

N oSprayGun-- Controlsthe application of water onto

cleaningsurfacewith trigger device.Includestrigger IocL

P o High Pressure Nasa-- Connectoneend to water pump

andthe other endto spraygun.

R oAccessaryTray -- Providesconvenient storage for

standard and optional accessories,such as brushes,

turbo wands,etc.

items Nat Shawn:

Identificatian Label(near rear of base plate}-- Provides

model and serial number of pressure washer. Pleasehave

these readily availableif calling for assistance.

Warning/0perating Instrudians Tag- identifies hazards

and proper procedureto sta@/stoppressure washer.

ifyouhaveanyproblemsoperatingyourpressurewasher,

pleasecallthepressurewasherhelplineat(800)743-4115.

Pressure Washer Lecatien

Ciearanees and Air Mevement

_k WARNING Exhaustheat/gasescould ignite

combustibles, structuresor damagefueltank

causing afire, resultingin death,seriousinjury

and/or property damage.

, Keepat least5 ft. (1.5m) clearanceonall sidesof pressure

washerincludingoverhead.

Placepressurewasher outdoors in an areathat will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas could accumulateand enter inside

or be drawn into a potentially occupied building. Ensure

exhaustgas (A) is kept awayfrom any windows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in aconfined area. Prevailingwinds andair

currents should be taken into considerationwhen positioning

_ressurewasher.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

. Operatethis product ONLYoutdoors.

Keepexhaustgas from entering a confined areathrough

windows, doors,venfibfion intakes,or other openings,

DO NOToperatethis product insideany building, carport,

porch, mania equipment, marineapplications, or enclosure=

evenif windows and doors areopen.

Haw to Start Your Pressure Washer

To start your pressure washer for the first time, follow these

instructions step-by-step. This starting information also

applies if you haveletthe pressure washer sit idle for at bast

a day.

1. Placepressurewasher near an outside watersource

capableof supplying water at a flow rategreaterthan

3.3 gallons (12.5 I) per minute and no lessthan 20 PSi

(1.38 BARS)at pressurewasher endof garden hose.

DONOTsiphon supply water.

2. Checkthat high pressure hoseis tightly connectedto

spray gun and pump. SeeAssembly section.

3. Make sure unit is in a level position.

4. Connectgarden hoseto water inlet on pressure washer

pump.

NOTICE DONOTrun the pump without the water supply

connectedandturned on.

Damageto equipmentresultingfromfailuretofollowthis

instructionwillvoidwarranty.

5. Turn ONwater, point gun in a safedirection, press red

button andsqueezetrigger to purge pump system of air

and impurities,

6. Attach nozzleextensionto spray gun. Tighten by hand.

Choosespray tip you want to use,pull backon collar of

nozzleextension, insert spraytip and releasecollar. Tug

on spray tip to makesure it is securely in place. See

How to Use@ray Tips.

NOTICE Beforestarting the pressure washer, be sureyou

are wearing safety goggles asdescribed below.

_k WARNING Riskof eyeinjury.

Spray could splash back or propelobjects

resulting in serious injury.

* Alwayswear indirect vented (chemicalsplash) safetygoggles

markedto comply with ANSi Z8X1 when using or in vicinity of

this equipment.

NEVERsubstitute safetyglasses or dry-condition goggles for

indirect vented safetygoggles.

Whenstarting engine,positionyourself as recommended

and start engineaccordingto instructions givenin

engineoperator's manual.Also seeoperating

instructions tag locatedon the pressurewasher.

WARNING Starter cord kickback (rapid retraction) will

pull hand and arm toward engine faster than you

_a_ can let which could cause broken bones,

fractures, bruises, or sprains resulting in serious

injury.

, NEVERpullstarter cord without first relieving spraygun

pressure,

When starting engine, pull cord slowly until resistance iSfelt

andthen pull rapidly to avoid kickback,

After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button and squeeze

spray gun trigger to releasehigh pressure,

Firmly grasp spray gunwith both hands when usinghigh

pressure sprayto avoid injury when spraygun kicks back.

,A WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

DONOTallowCHILDRENtooperatepressurewasher.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

NEVERaimspraygunatpeople,animals,or plants.

DONOTsecuresprayguninopenposition.

DONOTleavespraygununattendedwhilemachineis running.

NEVERuseaspraygunwhichdoesnothaveatriggerlockor

triggerguardin placeandin workingorder.

Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

,a, WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

DO NOTtouch hot parts and AVOIDhot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least5 feet (1.5 m) of clearanceon ail sidesof pressure

washer including overhead.

it is a violation of California PuNic Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark attester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions may have similar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain aspark attester designed for the exhaust system

installed on this engine.

Replacement parts must bethe sameand installed in the same

position as the original parts.

Hew to Step Your Pressure Washer

1. Releasespray gun trigger and let engine idle for two

minutes.

2. Turn engine off according to instructions given in

engine operator's manual.

3. ALWAYS point gun in a safe direction, press red button

and squeeze spray gun trigger to release retained high

water pressure.

,_, WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Hawte UseAccessoryTray

Theunit is equipped with anaccessorytray with placesto

store your spray gun, nozzle extension, high pressure hose

and quick connect spray tips.

1. Place nozzle extension through hob on accessory tray

on left side of unit.

2. Placespraygun through hob on accessorytray on

right side of unit.

12 www.brutepewer.eem

3. insert multi-colored spray tips in holesprovided on

front of accessorytray.

4. Placeone end of high pressure hose in grooveat top of

accessorytray and wrap high pressure hosearound

hooks asshown.

How to Use Spray Tips

The quick-connect on the nozzleextensionallows you to

switch betweenfour different quick connect spray tips. Spray

tips can be changedwhile pressurewasher is running once

spray gun trigger is locked.Thespraytips vary the spray

pattern as shown.

Fallow these instructionsto change spray tips:

1. Pull back collar on quick-connect and puff current

spray tip offi Store spray tips in holder provided on the

nozzleextension.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

* NEVERexchangespraytipswithoutthetriggerlockbeing

engagedonthespraygun.

* DONOTtwist spraytips whilespraying.

2. Select desiredspraytip:

Low Pressure

Black

Useto apply

detergent

40° White

21O0PSI

2.3 GPM

15° Yellow 0° Red

2600 PSI

2.1 GPM

° For gentle rinse,selectwhite 40° spraytip.

o To scour surface, selectyellow 15° or red 0° spray tip.

o To applydetergent, select black spray tip.

3. Pul backon collar,insert newspraytip and releasecollar.

Tugonspraytip to makesureit is securelyin place.

Usage Tips

* For most effective cleaning,keepspray tip from 8 to

24 inches _20to 61cm) awayfrom cleaning surface.

o if you get spraytip too close, especiallyusing a high

pressure spray tip, you may damagesurface being

cleaned.

o DONOTget closer than 6 inches (15 cm) when

cleaningtires.

Applying Detergent

A WARNING ChemicalBurn Hazard.

Chemicals could cause burns resulting in death,

serious injury, and/or property damage.

* DO NOTuse caustic liquid with pressure washer.

* Use ONLYpressurewasher safe detergents/soaps. Followall

manufacturers instructions.

Ta apply detergent, fallow these steps:

1. Reviewuse of spraytips.

2. Preparedetergent solution as required by job.

3. Placeendof detergentsiphoning tube into detergent

container.

NOTICE Make surethe tube is fully submerged in detergent

while applying detergent.

NOTICE Contact with the hot muffler could damage

detergent siphoning tube.

, When inserting the siphon into adetergent solution bottle, route

the tube so as to keep it from inadvertently contactingthe hot

muffler.

4. Make sure black spray tip is installed.

NOTICE Detergentcannot be applied with the high pressure

spray tips (White, Yellow or Red).

5. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connectedto spray

gun and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

Starting the engine without all the hoses connected andwithout

the waterturned ON coulddamagethe pump.

Damageto equipment resulting from failure to follow this

instruction will void warranty.

6. Start enginefollowing instructions How to Start Your

Pressure Washer.

7. Apply detergentto a dry surface, starting at lower

portion of areato bewashed andwork upward, using

long, even, overlapping strokes.

8. Allow detergent to "soakin"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergentto dry on

(prevents streaking).

NOTICE You must flush the detergent siphoning system

after each use by placingthe siphoning tube into a bucket of

cleanwater, then run the pressurewasher n low pressure

for 1-2 minutes.

Pressure Washer Rinsing

Fer Rinsing:

1. Removeblackspray tip from nozzleextension.

2. Select and install desired high pressure spray tip

following instructions How to UseSpray Tips.

3. Keepspray gun a safe distance from areayou plan to

spray.

WARNING Kickbackfrom spray gun could causeyou

to fall resulting in deathor serious injury.

4. Apply a high pressure spray to a small areaandthen

checksurface for damage, if nodamageis found, you

can assumeit is okay to continue rinsing.

5. Start attop of areato berinsed, working down with

same overlapping strokes asyou used for cleaning.

Cleaning Detergent $iphening Tube

if you usedthe detergent siphoning tube, you must flush it

with cleanwater before stopping the engine.

Placedetergentsiphoning tube ina bucketfull of clean

water.

Removehigh pressure spray tip from nozzleextension.

Select and install blackdetergent spray tip following

instructions How to UseSpray Tips.

Flush for 1-2 minutes.

Shut off engine following instructions How to Stop

Pressure VVasherandturn off watersupply.

ALWAYSpoint spraygun in a safe direction, press red

button and squeezespraygun trigger to release

retained high water pressure.

A WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

° Keephighpressurehoseconnectedto pumpandspraygun

whib systemispressurized,

o ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine,

Autematic CeetDewn System(Thermal Relief}

if you run the engineon your pressure washer for

3-5 minutes without pressingthe trigger on the spray gun,

cimulating water in the pump can reachtemperatures above

125°F (51°C).The system engagesto cool the pump by

discharging the warm water ente the ground.

* Operatepressurewasher from a stable surface.

Beextremely careful if you must usethe pressurewasherfrom

a ladder,scaffolding, or any other similar location.

Firmly grasp spray gunwith both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

Maintenance

General Recommendations

Regular maintenancewill improve the performance and

extendthe fifeof the pressurewasher.Seeanyqualified

dealerfor service.

The pressurewasher's warranty does not cover items that

havebeensubjectedto operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain the pressurewasher as instructed inthis manual,

including proper storage as detailedin VVinterStorageand

Long TermStorage.

NOTICE Should you havequestions about replacing

components on your pressure washer, pleasecarl

(888) 743o4115for assistance.

. Some adjustmentswill needto bemade periodically to

properly maintain your pressurewasher. Checkthe

spray gun and nozzleextensionassemblyfor wear.

. All maintenancein this manualandthe engineoperator's

manualshould bemadeat bast onceeachseason.

. Onceayear you should cleanor replacethe spark plug,

cleanor replacethe air filter. A newspark plug and

cleanair filter assureproper fuebair mixture and he p

your engine run better and last longer. Pleasereferto

your engineoperator's manualfor more details.

Befere EachUse

1. Checkengineoil level.

2. Cleandebris.

3. Checkwater inlet screen for damage.

4. Checkhigh pressure hosefor leaks.

5. Checkdetergent siphoning tube for damage.

6. Checkspray gun and nozzleextensionfor leaks.

7. Rinse out garden hoseto flush out debris.

Pump Oil

DONOTattempt anyoil maintenanceon this pump. The

pump is pre-lubricated and sealedfrom the factory, requiring

no additional maintenancefor the fife of the pump.

PressureWasher Maintenance

Clean Debris

Da@or beforeuse,cleanaccumulateddebris from pressure

washer.Keeprink@e,spring andcontroB dean. Keeparea

around and behind mufflerfree from anycombustibb debris.

inspect coofing air slots and openingsonthe pressure

washer.Theseopeningsmust bekeptcleanand unobstructed.

pressure washer parts should be kept cleanto reducethe

risk of overheating and ignition of accumulated debris.

* Use a damp cloth to wipe exterior surfaces clean.

NOTICE improper treatment of pressurewasher could

damageit and shorten its life.

, DONOTinsertanyobjectsthroughcoolingslots.

* Useasoft bristle brush to loosen cakedon dirt, oil, etc.

. Usea vacuum cleanerto pick up loose dirt and debris.

Cheekand Clean Inlet Screen

Examinethe screen on the pump's water inlet. Cleanit ifthe

screen is clogged or replaceit if screen is damaged.

CheckHigh Pressure Hese

Thehigh pressure hosecan developleaksfrom wear,

kinking, or abuse, inspectthe hoseeachtime beforeusing it.

Checkfor cuts, leaks,abrasionsor bulging of cover,damage

or movement of couplings, if any of theseconditions exist,

replacethe hose immediately.

,A WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

* NEVERrepairhighpressurehose.Replaceit.

ReplacementhoseratingMUSTequalorexceedmaximum

pressureratingofunit.

CheckDetergent Siphening Tube

Examinethe detergent tube and clean if clogged. Thetube

should fit tightly on the barbedfitting. Examinethe tube for

leaks or tears. Replacethe tube if damaged.

Detergent Siphening CheckBail

Occasionallycheck ball in detergentsiphoning system may

become stuck from storage, dried soap, or minerals in water.

Thecheck ballcan be freed by performing the following:

NOTICE Beforeperforming this procedure, be sure you are

wearing safety goggles asdescribed below.

A WARNING Riskof eyeinjury.

Spray could splash back or propelobjects

resulting in serious injury.

o Always wear indirect vented (chemical splash) safetygoggles

markedto comply with ANSi Z8X1 when using or in vicinity of

this equipment.

, NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles,

Shut off engine and turn off water supply.

ALWAYSpoint spraygun in a safe direction, press red

button and squeezespraygun trigger to release

retained high water pressure.

,A WARNING The high pressure stream of water that

_, his equipmentproduces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

3, Removedetergentsiphoning hosefrom barbed fitting

on pump.

4. Usinga firm, blunt object 7/64" in diameter or smaller,

by at bast 1" long, such as an Allen wrench, slowly

insert the object into the barbedfitting until you meet

resistance.This resistance isthe check ball.

5. Slowly push down until you feel the ball move slightly,

push no more than 1/8". Slight pressure may be

requiredto freethe ball.

6. Repeatsteps 4 and 5 if necessary.

7. Reinstalldetergent siphoning hose onto barbfitting.

8. Treatwith PumpSaveras described in Protecting the

Pumpduring storage to prevent reoccurrence.

CheckSpray Gun

Examinethe hose connectionto the spray gunand make

sure it is secure.Testthe trigger by pressing the red button

and making surethe trigger "springs back" into placewhen

you releaseit. You should not be able to press the trigger

without pressing the red button. Replacespraygun

immediately if it fails any of thesetests.

Nezzie Maintenance

A pulsing sensationfelt while squeezingthe spray gun

trigger may be caused by excessivepump pressure. The

principal causeof excessivepump pressure is a spray tip

clogged or restricted with foreign materials,such asdirt, etc.

To correct the problem, immediately cleanthe spray tip

following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYSpoint spray gun in a safe direction, press red

button and squeezespray gun trigger to release

retainedhighwater pressure.

WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized_

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine_

3. Removespraytip from end of nozzleextension.

4. Use a small paperclip to free anyforeign material

clogging or restricting spray tip (A).

5. Removenozzleextensionfrom spray gun.

6. Using a garden hose, remove additional debris by back

flushing water through nozzleextension. Backflush

between 30 to 60 seconds.

10.

11.

Reinstall spraytip into nozzleextension.

Reconnect nozzleextensionto spray gun.

Make sure garden hose is connectedto water inleL

Checkthat high pressure hoseis connectedto spray

gun and pump. Turn on water.

Start enginefollowing instructions How to Start Your

Pressure Washer.

Test pressurewasher by operatingwith eachquick

connect spray tip.

O°RingMaintenance

Purchasean O-Ring/Maintenance Kit, model 196002GS by

contacting the nearestauthorized service center, it is not

included with the pressurewasher. This kit includes

replacemento-rings, rubber washer andwater inlet filter.

Referto the instruction sheet provided in the kit to service

your unit's o-rings.

,a, WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

NEVERrepairleakingconnectionswithsealantofanykind.

Replaceo-ringor seal.

16 www.brutepewer.cem

Engine Maintenance

Seethe engine operator's manualfor instructions on howto

properly maintain the engine.

A CAUTmONAvoid prolongedor repeatedskin contact

with usedmotor oil.

, Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOiL TOCOLLECTIONCENTERS.

inspect IVluffier and Spark Attester

inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for

damage or carbon blockage, if replacement parts are

required, make sure to use only original equipment

replacement parts.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death,

serious injury and/or property damage.

Contact with muffler area could cause burns resulting in

serious injury.

o DO NOTtouch hot parts and AVOID hot exhaust gases.

Allow equipment to cool beforetouching.

Keepat least5 feet (1.5 m) of clearanceon all sidesof pressure

washer including overhead.

it is a violation of California PuNic Resource Code.Section

4442, to use or operate the engineon anyforest=covered.

brush=covered,or grass=coveredland unlessthe exhaust

system is equipped with aspark attester, as defined in Section

4442, maintained ineffective working order. Other states or

federal jurisdictions may havesimilar aws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkattester designedfor the exhaust system

installed on this engine.

Replacement parts must bethe sameand installed in the same

position as the original parts.

After Each Use

Water should not remain in the unit for long periods of time.

Sediments or minerals can deposit on pump parts and freeze

pump action. Followthese procedures after every use:

1. Shut off engine,turn off water supply, point gun in a

safe direction, press red button and squeezetrigger to

relievetrapped pressure, andlet engine cool.

A WARNING The high pressure stream of water that

this equipment produces could cut through skin

and its underlying tissues, resulting inserious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which could result in

serious injury.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

2, Disconnect hosefrom spray gun and high pressure

outlet on pump, Drainwater from hose, gun, and nozzle

extension. Use a rag to wipe off the hose.

3. Placethe spray gun, nozzleextensionandhigh

pressure hosein the accessorytray.

4. Empty pump of all pumped liquids by pulling recoil

handle about six times. This should remove most liquid

in pump.

5. Store unit in a clean,dry area.

6. if storing for more than 30 days,see Long Term

Storageon next page.

A WARNING Fueland its vapors areextremelyflammable

andexplosivewhich could causeburns,

fire or explosionresulting in death,

seriousinjury and/orpropertydamage.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

o Store awayfrom furnaces, stoves water heaters,clothes

dryers, or other appliancesthat havepilot light or other ignition

source becausethey could ignite fuel vapors,

Winter Storage

NOTICE You must protect your unit from freezing

temperatures.

, Failureto do so will permanently damageyour pump and render

your unit inoperable.

* Freezedamage is not covered underwarranty.

Te protectthe unit from freezing temperatures:

1. Follow steps 1-4 in the previous section After EachUse.

2. Use pump saver, Model 6039, to treat pump. This

minimizes freezedamageandlubricates pistons and

seals.

3. If pump saver is not available,connect a 3 ft. (92 cm)

section of garden hoseto waterinlet adapter. Pour

RV-antifreeze(antifreezewithout alcohol) into hose.

PuiIrecoil handletwice. Disconnect3 ft. (92 cm) hose.

4. Store unit in a clean, dry area.

Long Term Storage

if you do not plan to usethe pressure washer for morethan

30 days,you must preparethe engine and pump for long

term storage.

Protect Fuel System

FuelAdditive:

Fuelcan becomestalewhen stored over 30 days. Stab fuel

causesacid andgum deposits to form in the fuel system or

on essentialcarburetor parts. To keepfuel fresh, use Briggs

& Stratten@ AdvancedFormula FuelTreatment &

Stabilizer, availablewherever Briggs & Stratton genuine

service parts are sold.

For enginesequippedwith a FRESHSTART@fuel cap, use

Briggs & Stratten FRESHSTART@availableina drip

concentrate cartridge.

Thereis no needto drain gasolinefrom the eng ne if afuel

stabilizer is added according to instructions. Runthe engine

for 2 minutesto circulate the stabilizerthroughout the fuel

system before storage.

if gasoline in the engine hasnot beentreatedwith a fuel

stabilizer, it must be drained into an approvedcontainer. Run

the engine until it stops from lack of fuel. The useof a fuel

stabilizer in the storagecontainer is recommendedto

maintain freshness.

Storing the Engine

Seethe engine operator's manualfor instructions on howto

properly preparethe engine for storage.

Protecting the Pump

To protect the pump from damagecaused by mineral

deposits or freezing, use PumpSaver,Model 6039, to treat

pump. This preventsfreezedamageandlubricates pistons

and seals.

NOTICE PumpSaveris availableas an optional accessory, it

is not included with the pressurewasher. Contactthe nearest

authorized servicecenterto purchasePumpSaver.

NOTICE You must protect your unit from freezing

temperatures.

, Failureto dosowillpermanentlydamageyourpumpandrender

yourunitinoperable.

* Freezedamageisnotcoveredunderwarranty.

To use PumpSaver,makesurethe pressurewasher is turned

off and disconnectedfrom supply water. Readandfollow all

instructions and warnings given on the PumpSaver

container.

Other Storage Tips

1. DONOTstorefuel from one seasonto another unless it

has beentreated as described in Protect FuelSystem.

2. Replacefuel container if it starts to rust. Rustand/or

dirt in fuel can cause problems if it's usedwith this

unit.

3. Cover unit with a suitable protective coverthat does not

retain moisture.

A WARNING Storagecovers could causea fire

resulting in death,serious injury and/or property

damage.

* DO NOTplace astorage cover overa hot pressure washer,

Let equipment coolfor a sufficient time before placingthe cover

4. Store unit in acleanand dry area,

18 www.hrutepower.eom

Problem

Detergent faiJs to mix with spray.

Enginetuns good at flo-Joadbut

"bogs" whefl Joadis added.

EnginewiJJnot start;starts and tuns

tough, or shuts down during

operation.

EngineJackspower.

Cause

1. Low pressure spray tip installed.

2. Water inlet is blocked.

3. Inadequatewater supply.

4. Inlet hose is kinked or leaking.

5. Cloggedinlet hose screen.

6. Water supply is over 100°F.

7. High pressure hose is blocked or

leaks.

8. Spraygun leaks.

9. Spraytip is obstructed.

10. Pump is faulty.

1. Detergentsiphoning tube is not

submerged.

2. Detergentsiphoning tube is

JCottection

1. Replacewith high pressure spraytip.

2. Clearinlet.

3. Provide adequatewater flow.

4. Straighten inlet hose, patch leak.

5. Checkandcleaninlet hosescreen.

6. Provide cooler water supply.

7. Clearblocks in outlet hose.

8. Replacespray gun.

9. Cleanspraytip.

10. Contact local servicefacility.

1. Insert detergent siphoning tube into

detergent.

2. Cleanor replacedetergentsiphoning

clogged or cracked.

3. High pressure spray

4. Detergentsiphonir

stuck.

cmeaoer,

3. of fuel.

4. Stalefuel.

tube.

!h low pressure spray tip.

siphoning check ball.

control to FASTposition. If

still "bogs down", contact local

servicefacility.

1. Fill crankcaseto proper level.

2. Cleanor replaceaircleaner.

3. Fill fuel tank.

4. Drainfuel tank; fill with fresh fuel.

5. Spark p!ugwii_;not connectedto

spar_ .....

ad i:

a eI.

r chfuemm xture.

Dirty '_irfilter.

5. Connectwire to spark plug.

6. Replacespark plug.

7. Drainfuel tank; fill with fresh fuel.

8. Contact local servicefacility.

Replaceair filter.

EffectiveJanuary 1,2010; replaces aft undated Warranties and all Warranties dated before January 1,2010.

LIIVIITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the pressure washer that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealerin

our dealer Iocator map at BRIGGSandSTRATTON.COM.

THEREIS NO OTHEREXPRESSWARRANTY. IMPLIEDWARRANTIES, INCLUDINGTHOSEOFMERCHANTABILITYANDFITNESSFORA PARTICULAR

PURPOSE,ARELIMITED TOONEYEARFROM PURCHASE,ORTOTHE EXTENTPERMITTEDBY LAW. ANY ANDALL IMPLIED WARRANTIESARE

EXCLUDED.LIABILITY FORINCIDENTALOR CONSEQUENTIALDAMAGESARE EXCLUDEDTOTHE EXTENTEXCLUSIONIS PERMITTEDBY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the excJusJonor limitation

of incidental or consequential damages, so the above limitation and exclusion may not applyto you, This warranty gives you specific bgal rights and

you may also have other rights which vary'from state to state or country'to country'.

Consumer Use 2 years

Commercial Use 90 days

The warranty' period begins onthe dateof purchase by the first retail consumer or commercial end user and continues for the period of time stated above.

"Consumer use"means personal residential household use by a retail consumer '"Commercial use means all other uses ncJuding use for commercial,

income producing or rental purposes. Onceequipment has experiencedcommerdal use. it shaft thereafter beconsidered as commercial usefor purposes of

this warranty'.

NOWARRANTY REGISTRATIONIS NECESSARYTO OBTAINWARRANTY"ON BRiGGS& STRATTONPRODUCTS.SAVEYOURPROOFOFPURCHASE

RECEIPT.IF YOU DONOTPROVIDEPROOFOFTHEINITIAL PURCHASEDATEAT THETIN1EWARRANTYSERVICEiS REQUESTED,THE MANUFACTURING

DATEOFTHE PRODUCTWILL BE USEDTODETERMINETHEWARRANTY PERIOD.

We welcome warranty repair andapologize to you for being inconvenienced. Any Authorized Service Dealermay perform warranty' repairs. Most warranty'

repairs are handled routinely, but sometimes requests for warranty' service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty' is void if the manufacturing dateor the serial number on the pressure washer or engine has been removed or the equipment has beenaltered or

modified. During the warranty' period, the Authorized Service Dealer,at its option, will repair or replaceany part that, upon examination, is found to be

defective under normal use and service. This warranty will not cover the following repairs and equipment:

Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty' also does not

cover normal maintenance such as air filters, adjustments, fuel system cleaning and obstruction (due to chemical, lime, dirt, and so forth).

Installation and Nlaiatenaace: This warranty' does not apply to equipment or parts that have been subjected to improper or unauthorized installation or

alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,

to adversely affect its performance and reliability. This warranty' also does not cover normal maintenance such as air filters, adjustments, fuel system

cleaning and obstruction (due to chemical, lime, dirt, and so forth).

Other Exclusions: This warranty' excludesthe engine. For engine warranty' questions, carlAmerican Honda Motor Companyat 1-800-426-7701 or visit

www.honda-engines.com for a dealer Iocator.

It also excludes wear items such as quick couplers, seals, o-rings, pumps that have beenrun without water supplied or damage or malfunctions

resulting from accidents, abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts, such as guns,

hoses,nozzle extensions (wands), and nozzles,are excluded from the product warranty'.This warranty' excludes used, reconditioned, and