Gigabyte 7ZXR Series User manual

Category
Motherboards
Type
User manual

This manual is also suitable for

FCC Compliance Statement:
This equipment has been tested and found to
comply with limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable
protection against harmful interference in
residential installations. This equipment
generates, uses, and can radiate radio
frequency energy, and if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause interference to radio or
television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna
-Move the equipment away from the receiver
-Plug the equipment into an outlet on a circuit different from that to which
the receiver is connected
-Consult the dealer or an experienced radio/television technician for
additional suggestions
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void Your
authority to operate such equipment.
This device complies with Part 15 of the FCC Rules. Operation is subjected to
the following two conditions 1) this device may not cause harmful interference
and 2) this device must accept any interference received, including interference
that may cause undesired operation.
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name: G.B.T. INC.
Address: 18305 Valle
y
Blvd., Suite#A
LA Puent, CA 91744
Phone/Fax No: (818) 854-9338/ (818) 854-9339
hereby declares that the product
Product Name:
Model Number:
Mother Board
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),
Class B Digital Device
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful
and (2) this device must accept any inference received, including
that may cause undesired operation.
Representative Person's Name: ERIC LU
Signature:
Date: Feb. 09, 2001
Eric Lu
GA-7ZXR
Declaration of Conformity
We, Manufacturer/Importer
(full address)
G.B.T. Technology Träding GMbH
Ausschlager Weg 41, 1F, 20537 Hamburg, Germany
declare that the product
( description of the apparatus, system, installation to which it refers)
Mother Board
GA-7ZXR
is in conformity with
(reference to the specification under which conformity is declared)
in accordance with 89/336 EEC-EMC Directive
EN 55011
Limits and methods of measurement
EN 61000-3-2*
Disturbances in supply systems caused
of radio disturbance characteristics of
EN60555-2
by household appliances and similar
industrial, scientific and medical (ISM elect
r
ical equipment “Harmonics”
high frequency equipment
EN55013
Limits and methods of measurement
EN61000-3-3*
Disturbances in supply systems caused
of radio disturbance characteristics of
EN60555-3
by household appliances and similar
broadcast receivers and associated electrical equipment “Voltage fluctuations”
equipment
EN 55014
Limits and methods of measurement
EN 50081-1
Generic emission standard Part 1:
of radio disturbance characteristics of
Residual, commercial and light industry
household electrical appliances,
portable tools and similar electrical
EN 50082-1
Generic immunity standard Part 1:
apparatus Residual, commercial and light industry
EN 55015
Limits and methods of measurement
EN 55081-2
Generic emission standard Part 2:
of radio disturbance characteristics of Industrial environment
fluorescent lamps and luminaries
EN 55020
Immunity from radio interference of
EN 55082-2
Generic immunity standard Part 2:
broadcast receivers and associated Industrial environment
equipment
EN 55022
Limits and methods of measurement
ENV 55104
Immunity requirements for household
of radio disturbance characteristics of appliances tools and similar apparatus
information technology equipment
DIN VDE 0855
Cabled distribution systems; Equipment
EN 50091- 2
EMC requirements for uninterruptible
part 10
for receiving and/or
distribution
from power systems (UPS)
part 12
sound and television signals
CE marking
(EC conformity marking)
The manufacturer also declares the conformity of above mentioned product
with the actual required safety standards in accordance with LVD 73/23 EEC
EN 60065
Safety requirements for mains operated
EN 60950
Safety for information technology equipment
electronic and related apparatus for including electrical business equipment
household and similar general use
EN 60335
Safety of household and similar
EN 50091-1
General and Safety requirements for
electrical appliances uninterruptible power systems (UPS)
Manufacturer/Importer
Signature
:
Rex Lin
(Stamp)
Date : Feb. 09, 2001 Name : Rex Lin
7ZXR Series
AMD Athlon
TM
/Duron
TM
Socket A Motherboard
USER'S MANUAL
AMD Athlon
TM
/Duron
TM
Socket A Processor Motherboard
REV. 3.0 Frist Edition
R-3.0-01-010510
How This Manual Is Organized
This manual is divided into the following sections:
1) Revision History
Manual revision information
2) Item Checklist
Product item list
3) Features
Product information & specification
4) Hardware Setup
Instructions on setting up the motherboard
5) Performance & Block Diagram
Product performance & block diagram
6) Suspend to RAM & Dual BIOS
Instructions on STR installation & Dual
BIOS
7) Four Speaker & SPDIF
Four Speaker & SPDIF introduction
8) @BIOS & Easy Tune///
TM
Instructions on @BIOS & Easy Tune///
TM
9) RAID
Instructions on RAID
10) BIOS Setup
Instructions on setting up the BIOS
software
11) Appendix
General reference
Table Of Content
Revision History P.1
Item Checklist P.2
Summary of Features P.3
7ZXR Series Motherboard Layout P.5
Page Index for CPU Speed Setup / Connectors / Panel and Jumper
Definition
P.6
Performance List P.26
Block Diagram P.27
Suspend to RAM Installation P.28
Dual BIOS Introduction P.34
Four Speaker & SPDIF Introduction P.42
@BIOS Introduction P.48
Easy Tune///
TM
Introduction P.49
RAID Introduction P.51
Memory Installation P.74
Page Index for BIOS Setup P.75
Appendix P.105
7ZXR Series Motherboard
1
Revision History
Revision Revision Note Date
2.1 Initial release of the 7ZXR Series motherboard user’s
manual.
Dec. 2000
2.2 Initial release of the 7ZXR Series motherboard user’s
manual.
Jan. 2001
2.2 Second release of the 7ZXR Series motherboard user’s
manual.
Feb. 2001
2.3 Initial release of the 7ZXR Series motherboard user’s
manual.
Apr. 2001
3.0 Initial release of the 7ZXR Series motherboard user’s
manual.
May. 2001
The author assumes no responsibility for any errors or omissions that may appear in this
document nor does the author make a commitment to update the information contained herein.
Third-party brands and names are the property of their respective owners.
May. 10, 2001 Taipei, Taiwan, R.O.C
Item Checklist
2
Item Checklist
;
The 7ZXR Series motherboard
;
Cable for IDE / floppy device
;
Diskettes or CD (TUCD) for motherboard driver & utility
;
7ZXR Series user’s manual
7ZXR Series Motherboard
3
Summary Of Features
Form Factor
y
30.5 cm x 24.4 cm ATX size form factor, 4 layers PCB.
Motherboard
y
7ZXR Series includes 7ZXR , 7ZXR-C
CPU
y
AMD Athlon (K7) Socket A Processor
y
256K/64K L2
cache on die
y
Supports 500MHz ~ 1GHz
Chipset Apollo KT133A ,consisting of:
y
VT8363A Memory/AGP/PCI Controller(PAC)
y
VT82C686B PCI Super-I/O Integrated Peripheral
Controller (PSIPC)
Clock Generator
y
ICS94236AF
95 / 100 / 102 / 105 / 110 / 113 / 115 / 120 / 133 / 135 / 137 /
139 / 141 / 143 / 145 / 150 MHz system bus speeds
Memory
y
3 168-pin DIMM sockets
y
Supports PC-100 / PC-133 SDRAM and VCM SDRAM
y
Supports up to 1.5GB DRAM
y
Supports 3.3V / 3.4V / 3.5V SDRAM DIMM
I/O Control
y
VT82C686B
Slots
y
1 AGP slot supports 4X mode 1.5V ,1.6V ,1.7V & AGP
2.0 compliant
y
6 PCI slots support 33MHz & PCI 2.2 compliant
y
1 AMR(Audio Modem Riser) slot
On-Board IDE
y
IDE 1and IDE 2 Supports UDMA 33 / ATA 66/ATA100
IDE & ATAPI CD-ROM
y
IDE 3 and IDE 4 Compatible with RAID, Ultra ATA/100,
Ultra ATA/66, Ultra ATA/33, EIDE (Optional)
y
4 IDE bus master IDE ports for up to 8 ATAPI devices
On-Board
Peripherals
y
1 floppy port supports 2 FDD with 360K, 720K,1.2M,
1.44M and 2.88M bytes
y
1 parallel ports supports Normal/EPP/ECP mode
y
2 serial ports (COM A and COM B)
y
4 USB ports
y
1 IrDA connector for IR
Hardware Monitor
y
CPU/System fan revolution detect
y
CPU/System temperature detect
y
System voltage detect
To be continued…
Summary of Features
4
PS/2 Connector
y
PS/2
Keyboard interface and PS/2
Mouse
interface
On-Board Sound
y
Creative CT5880 sound
y
AC’97 CODEC
y
Line In/Line Out/Mic In/AUX In/CD In/TEL/Game Port
/Four Speaker & SPDIF
On-Board RAID
(Optional)
y
Support data striping (RAID 0) or mirroring (RAID 1) .
y
Supports concurrent dual IDE controller operation.
y
Supports IDE bus master operation.
y
Displays status and error checking messages during
boot-up.
y
Mirroring supports automatic background rebuilds
y
Features LBA and Extended Interrupt13 drive
translation in controller onboard BIOS.
BIOS
y
Licensed AMI BIOS, 2M bit flash ROM
y
Support Dual BIOS
Additional Features
y
Support Wake-On-LAN (WOL)
y
Support Internal / External Modem Ring On
y
Support USB KB/MS Wake up from S3
y
Includes 3 fan power connectors
y
Poly fuse for keyboard over-current protection
y
Support STR (Suspend-To-RAM) function
7ZXR Series Motherboard
5
7ZXR Series Motherboard Layout
7ZXR
PCI2
VT82C
686B
VT8363A
GAME & AUDIO
COM B
COM A
LPT
PS/2
J3
J16
J15
J18
BAT1
J2
BZ1
FLOPPY
IDE2
IDE1
AGP 1
JP6
SW1
J11
LED1
J13
J12
J4
JP4
USB1
AMR
PCI3
Sigmtal
USB2
DIMM3
ATX POWER
DIMM2
DIMM1
PCI4
PCI5
MAIN
BIOS
BACK Up
BIOS
JP10
JP11
JP18
JP9
JP16
JP17
Creative
CT5880
Clock
Generator
IDE3
IDE4
JP3
JP19
JP20
JP7
JP21
SW4
SW5
SW3
PCI6
Socket A CPU
PCI1
SW6
J50
7ZXR Series Motherboard Layout
6
Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition
Page
CPU Speed Setup P. 7
Connectors P.10
ATX Power P.10
COM A / COM B / LPT Port P.10
Floppy Port P.11
Game & Audio Port P.11
IDE 1/IDE2 (Primary/Secondary), IDE3/IDE4(Promise RAID/ATA100) Port P.12
J2 (System Fan) P.12
J3 (CPU Fan) P.13
J4 (IR) P.13
J12 (Wake On LAN) P.14
J13 (Ring Power On) P.14
J15 (AUX_IN) P.15
J16 (TEL) P.15
J18 (CD Audio Line In) P.16
JP6 (Power Fan) P.16
JP8 / LED1 (STR LED Connector & DIMM LED) P.17
PS/2 Keyboard & PS/2 Mouse Connector P.17
USB 1 Connector P.18
USB 2 Connector P.18
Panel and Jumper Definition P.19
J11 (2x11 Pins Jumper) P.19
JP3 (Clear CMOS Function)[Optional] P.20
JP4 (Rear USB Device Wake Up Selection) P.20
JP7 (STR Function Enabled) P.21
JP9 (Onboard Sound Function Selection) P.21
JP10 (BIOS Write Protection)[Optional] P.22
JP11 (Front USB Device Wake Up Selection) P.22
JP16/JP17/JP18 (AMR Select) P.23
JP19 (Onboard Promise select) [Optional] P.23
JP20 (RAID/ATA100 Select) [Optional] P.24
J50 (NB Heat Sink Fan) P.24
BAT1 (Battery) P.25
7ZXR Series Motherboard
7
CPU Speed Setup
There are 2 ways to set system bus speed. To set system bus speed by BIOS, please refer to P.
95. To set system bus speed by DIP switch (
SW1
and
JP21)
. Please refer to table below.
Set System Bus Speed
SW1: (CPU Freq.)
O : ON,
X : OFF
CPU CLK PCI CLK 1 2 3 4 5
95.00 31.67 O O O O 0
100.00 33.33 O 0 X O 0
102.00 34.00 O 0 O X 0
105.00 35.00 O 0 X X O
110.00 36.67 X O O O 0
113.00 37.67 X O X O O
115.00 38.33 X O O X O
120.00 40.00 X O X X 0
133.33 33.33 O X 0 O O
135.00 33.75 O X X O O
137.00 34.25 O X O X O
139.00 34.75 O X X X O
141.00 35.25 X X O O O
143.00 35.75 X X X O O
145.00 36.25 X X O X O
150.00 37.50 X X X X O
100.90 33.63 O O O O X
100.00 33.33 O O X O X
103.00 34.33 O O O X X
107.00 35.67 O O X X X
117.00 39.00 X O O O X
120.00 30.00 X O X O X
123.00 30.75 X O O X X
125.00 31.25 X O X X X
133.33 33.33 O X O O X
133.90 33.48 O X X O X
147.00 36.75 O X O X X
151.00 37.75 O X X X X
153.00 38.25 X X O O X
155.00 38.75 X X X O X
160.00 40.00 X X O X X
200.00 50.00 X X X X X
CPU Speed setup
8
Ë
ËË
Ë
The FSB Speed of the VIA KT133A is 100MHz/133MHz.
SW1
JP21
Pin No. Definition
1-2 close CPU Clock
Frequency 133MHz
2-3 close CPU Clock
Frequency 100MHz
(Default)
1
The CPU speed must match with the frequency ratio. It will cause system hanging up if
the frequency ratio is higher than that of CPU.
0
AMD CPU Heat Sink Installation:
Beware: Please check that the heat sink is in good contact with the CPU before you turn on your
system.
The poor contact will cause over heat, and might cause damage to your
processor.
SW3: (CPU Over Voltage Tage)
O : ON,
X : OFF
FSB 1 2 3 4 5 6
Auto X X X X X X
1.5V 0 X X X 0 O
1.525V X 0 X X 0 O
1.55V 0 0 X X 0 O
1.575V X X 0 X 0 O
1.6V 0 X 0 X 0 O
1.625V X 0 0 X 0 O
1.65V 0 0 0 X 0 O
1.675V X X X 0 0 O
1.7V 0 X X 0 0 O
1.725V X 0 X 0 0 O
1.75V 0 0 X 0 0 O
1.775V X X 0 0 0 O
1.8V 0 X 0 0 0 O
1.825V X 0 0 0 0 O
1.85V 0 0 0 0 0 O
7ZXR Series Motherboard
9
SW4: (Memory Over Voltage )
SW5: (AGP Over Voltage )
SW6: (CPU Ratio )
O : ON,
X : OFF
0
00
0
Note: Please set the CPU host frequency in accordance with your processors
specifications. We don’t recommend you to set the system bus frequency over
the CPU’s specification because these specific bus frequencies are not the
standard specifications for CPU, chipset and most of the peripherals. Whether
your system can run under these specific bus frequencies properly will depend
on your hardware configurations, including CPU, Chipsets, SDRAM, Cards….etc.
FSB 1 2
3.3V ON ON
3.4V OFF ON
3.5V OFF OFF
FSB 1 2
1.5V ON ON
1.6V OFF ON
1.7V OFF OFF
FSB 1 2 3 4 5
Auto X X X X O
5X 0 O X O X
5.5X X 0 X O X
6X 0 X X O X
6.5X X X X O X
7X 0 O 0 X X
7.5X X 0 0 X X
8X 0 X 0 X X
8.5X X X O X X
9X 0 O X X X
9.5X X 0 X X X
10X 0 X X X X
10.5X X X X X X
11X 0 O 0 0 X
11.5X X 0 0 0 X
12X 0 X 0 0 X
12.5X X X O O X
SW3 & SW5
SW4 & SW6
Connectors
10
Connectors
ATX Power
Pin No. Definition
3,5,7,13,
15-17
GND
1,2,11 3.3V
4,6,19,20 VCC
10 +12V
12 -12V
18 -5V
8 Power Good
9 5V SB(stand by+5V)
14 PS-ON(Soft On/Off)
20 10
11
1
COM A / COM B / LPT Port
COM A
LPT Port
COM B
7ZXR Series Motherboard
11
Floppy Port
Red Line
FDD1
Game & Audio Port
MIC In
Game
Port
Line In/Line Out
Line Out 1
Line Out 1: Line Out or SPDIF (The SPDIF output is
capable of providing digital audio to external speakers
or compressed AC3 data to an external Dolby digital
decoder). To enable SPDIF, simply insert SPDIF
connector into Line Out1. Line Out1 will become
SPDIF Out automatically. (see page 43 for more
information).
To enable Four Speaker (for Creative 5880 audio
only), simply follow instructions on page 40 and Line
In will become Line Out2 to support second pair of
stereo speakers.
Connectors
12
IDE1,IDE2 (Primary/Secondary),
IDE3/IDE4(RAID/ATA100) Port(Optional)
IDE 1 IDE 2
Red Line
IDE 3 IDE 4
J2 : System Fan
Pin No. Definition
1 Control
2 +12V
3 NC
1
7ZXR Series Motherboard
13
J3 : CPU Fan
Pin No. Definition
1 Control
2 +12V
3 SENSE
1
J4 : IR
Pin No. Definition
1 VCC (+5V)
2 NC
3 IR Data Input
4 GND
5 IR Data Output
1
1 / 1

Gigabyte 7ZXR Series User manual

Category
Motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document