EVOC EC4­1812CLDNA User manual

EVOC
Brand
EVOC
Model
EC4­1812CLDNA
Category
Motherboards
Type
User manual
EC41812CLDNA
EPIC Single Board Computer with
CPU/Memory/VGA/LVDS/USB/COM
/SATA/LAN/Audio
Version: A1
Announcement
Whatcontainedinthis User Manualdoesnotrepresent the commitmentsofEVOC
Company. EVOC Company reserves the right to revise this User Manual, without
priornotice,andwillnotbeheldliableforanydirect,indirect,intendedorunintended
lossesand/orhiddendangersduetoinstallationorimproperoperation.
Before purchasing, pleasehave adetailedunderstanding of theproduct performance
toseewhetheritmeetsyourrequirements.
EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. All
trademarks,registered trademarks,andtrade namesused in thisUser Guide are the
propertyoftheirrespectiveowners.
EVOCIntelligentTechnologyCo.,Ltd.©2009,CopyrightReserved.Nopartofthis
manual can be reproduced in any form or by any means, such as in electronic or
mechanicalway,withoutpermissioninwritingfromEVOC.
SafetyInstructions
1. Beforehandlingyourproduct,readtheuser’smanualcarefully;
2. Any board or card not ready to be installed shall be kept in the antistatic
packaging;
3. Before taking board or card from antistatic packaging, put your hand on
groundedmetalobjectforawhile(about10seconds)toeliminatestaticonyour
body;
4. Whileholding a boardor card,pleasedo wearstaticprotectivegloves;always
holdaboardbyitsedges;
5. Before inserting, removing or reconfiguring motherboard or expansion card,
firstdisconnectthecomputerandperipheralsfromtheirpowersources;
6. Before removing boards or computer, turn off all power resources firstly and
disconnectthepowercordfrompowersource;
7. For PC Box products, when inserting or removing boards, disconnect the
computerand peripheralsfromthepowersourcesfirstly;
8. Before connectingorunplugging anyequipment,makesureallpowercordsare
unpluggedinadvance;
9. Toavoidunnecessarydamagecausedbyturningon/offcomputerfrequently,wait
atleast30secondsbeforereturningonthecomputer.
Contents
Chapter1ProductIntroduction ................................................................................1
Overview ............................................................................................................1
EnvironmentandMechanicalDimension .............................................................2
PowerConsumption ............................................................................................2
Microprocessor ...................................................................................................2
Chipsets ..............................................................................................................2
SystemMemory ..................................................................................................2
VideoFunction....................................................................................................2
NetworkFunction................................................................................................2
AudioFunction ...................................................................................................3
CFCard ..............................................................................................................3
SATA Function....................................................................................................3
PowerFeature .....................................................................................................3
ExpansionBus ....................................................................................................3
I/OFunctions ......................................................................................................3
Watchdog Function..............................................................................................3
Chapter2Installation...............................................................................................4
ProductOutline ...................................................................................................4
LocationsofInterfaces ........................................................................................5
JumperSettings...................................................................................................6
InterfaceforPower,HardDisk,WirelessNetworkCardIndicators........................7
LVDSBacklightControl......................................................................................7
USBInterface..................................................................................................... 8
SerialPort........................................................................................................... 8
VideoInterface ................................................................................................... 9
NetworkInterface ............................................................................................. 11
PowerInterface................................................................................................. 11
AudioInterface................................................................................................. 12
MultifunctionInterface ..................................................................................... 12
DigitalI/OInterface.......................................................................................... 13
SATA Interface ................................................................................................. 13
CFCard............................................................................................................ 14
MiniPCIEInterface.......................................................................................... 15
Chapter3BIOSSetup ........................................................................................... 16
Advanced ......................................................................................................... 17
Chipset............................................................................................................. 22
PCIPnP............................................................................................................. 23
Appendix.............................................................................................................. 24
Watchdog ProgrammingGuide.......................................................................... 24
DigitalIOProgrammingGuide ......................................................................... 26
I/O AddressMap............................................................................................... 29
IRQAssignmentTable ...................................................................................... 31
Chapter1ProductIntroduction
EC41812CLDNA 1
Chapter1ProductIntroduction
Overview
This board is a sort of embedded motherboard compliant with EPIC single board
specification, which is developed basing on the Intel® Atom platform; the board
adopts pin interfaces and is abundant in integration functions, complete in
performanceandhighinreliability;itsmainfeaturesareasfollows:
◆ Support ATOMN270CPU;
◆ Intel®945GSE+Intel®ICH7Mchipset;
◆ Onboard512MBDDR2 memory(couldbeexpandedto 1GB);
◆ Support VGA and LVDSdualdisplayfunction;
◆ Providesix USB2.0 highspeedinterfaces;
◆ Provideone 10/100/1000Mbps Ethernetcontroller;
◆ ProvideoneHDA audiointerface;
◆ Provide two SATA harddiskinterfacesandoneCF cardinterface;
◆ Provide eight COMs, four of which support RS232 and the other four
supportthreeline TTL level;
◆ Provideone MiniPCIEinterface;
◆ Provideone4bitinputand4bitoutputdigitalI/Ointerface;
◆ Single 5V power.
In addition, it also provides one multifunction interface with
keyboard/mouse/buzzer/reset functions and watchdog timer function. This product
could be widely used in the fields like medical monitor, analysis instrument and
electricpowerinspectionandmilitaryindustry.
Chapter1ProductIntroduction
2 EC41812CLDNA
EnvironmentandMechanicalDimension
l OperatingEnvironment:OperatingTemperature: 20℃~60℃;
Humidity: 5%~95%,noncondensing;
l StorageEnvironment:StorageTemperature: 40°C~80°C;
Humidity: 5%~95%,noncondensing;
l Dimension: 115.00mmx165.00mm
PowerConsumption
CPU: onboardIntel®Atom1.6G
Memory: onboard1G (or512M) DDR2533MHz
l +5V@2.8A; +5%/3%;
Microprocessor
ATOMN270CPU;
Chipsets
Intel® 945GSE+Intel® ICH7M;
SystemMemory
512MB or 1GBDDR2 memoryonboard;
VideoFunction
Intel®945GSEintegratesinsystem chip andsupport VGAandLVDS dualdisplay
function.
Net workFunct ion
The motherboard integrates one 10/100/1000Mbps Ethernet controller RTL8111C,
whichprovidesyouwithhighspeedandstablenetworkplatform.
Chapter1ProductIntroduction
EC41812CLDNA 3
AudioFunction
IntegrateonestandardHDA audiochipandprovideexcellentsoundeffect.
CF Card
Provide one Compact Flash card interface, which is easy to use and its storage
capacity willvarywiththecard inuse.
SATA Function
Two SATA hard disk interface, speed 3.0Gb/s(when using onboard SATA power
interface to supply power for SATA hard disk, only 2.5″ SATA hard disk is
supported; when using external power, both 2.5″ hard disk and 3.5″ hard disk are
supported).
PowerFeature
Single +5V powersupply;
ExpansionBus
One MiniPCIEinterface;
I/OFunctions
● Supporteight COMs,fourofwhichareRS232 interfaceswhiletheother
fourarethreelineTTLinterface;
● Supportsix USB2.0 interfaces;
● Onekeyboard/mouse/buzzer/RESET functioninterface;
● One4bitinput4bitoutputdigitalI/Ointerface.
WatchdogFunction
● 1~255m/sprogrammable;
● Overtimeinterrupt orsystemreset.
Chapter 2 Installation
4 EC41812CLDNA
Chapter2Installation
ProductOutline
154.84
165.00
104.85
5.08
5.08
115.00
Unit: mm
Chapter2Installation
EC41812CLDNA 5
LocationsofInte rfaces
AUDIO1 LAN1 USB3
USB2 USB1
VGA1
LVDS2
LVDS1
LCDB1
JLCDB1
JLCD1
PWR1
MPCIE1
J1
LED2
COM1
COM3
JCC1
GPIO1
COM2
COM4
COM6
COM5
JCF1
SATA1
SATA2
CF1
Tip:Howtoidentifythefirstpinofthejumpersandinterfaces
1. Observetheletterbesidethesocket,itwouldbemarkedwith“1”orthickened
linesortriangularsymbols;
2. Observethesolderpadontheback, thesquarepadisthefirstpin;
3. Theredline onthecableorothermarksshowsthatthey shouldbe connected
withthefirstpinofthesocket.
Chapter 2 Installation
6 EC41812CLDNA
JumperSettings
JCC1:Clear/Keep CMOS Setting
By changing the status of the jumper cap of CMOS to realize this function. If the
systemcannotstartupnormallyduetoimproperBIOSsetup,usersmaytrytoclear the
contentsofCMOS to restore the defaultvalueofthe system parameters andrestart
thesystem.
Setup Function
12Open Normal(Default)
JCC1
12Short
Clear the contents of CMOS, all BIOS setting will
restoretofactorydefaultvalues.
JCF1:CFCard OperatingVoltageSelecti on
Setup Function
12Short +3.3V (Default)
JCF1
23Short +5V
JLCDB1:LVDS B acklightVoltageSelection
Setup Function
12Short +12V(Default)
JLCDB1
23Short +5V
Chapter2Installation
EC41812CLDNA 7
JLCD1: LVDS OperatingVoltageSelection
Theboardprovidestwovoltageoptions,3.3Vand5V.OnlywhentheselectedLCD
voltage is in accord with the LCD voltage in use, the LCD screen could display
normally.
Setup Function
12Short +3.3V (Default)
JLCD1
23Short +5V
InterfaceforPower,HardDisk,WirelessNetworkCardIndicators
Pin SignalName Pin SignalName
1 FP_IDE_LED 2 FP_IDE_LED+
3 POWER_LED 4 POWER_LED+
LED2
5 WLAN_LED 6 WLAN_LED+
LVDSBacklightControl
Pin SignalName
1 VCC_LCDBKLT
2 LCD_BKLTCTL
3 LCD_BKLTEN
LCDB1
4 GND
Note: VCC_LCDBKLTbacklight power (power voltage is controlled by the
backlightvol tageselectingjumper);
LCD_BKLTCTLbacklightcontrol;
LCD_BKLTEN  backlightenabling.
Chapter 2 Installation
8 EC41812CLDNA
USBInte rface
USB1,USB2andUSB3arethe2×5Pin(2.0mm)USBdevicepins;thetransfercable
is required to connect the interface signals to the standard socket. The table below
showsthepin definitionsoftheinterfaces.
Pin SignalName Pin SignalName
1 +5V 2 +5V
3 USB1_Data 4 USB2_Data
5 USB1_Data+ 6 USB2_Data+
7 GND 8 GND
USB1/USB2/USB3
9 NA 10 GND_CHASSIS
SerialPort
1) COM1/COM2/COM3/COM4:RS232
COM1, COM2, COM3 and COM4 are 2×5Pin (2.0mm) COM device pins; the
transfercableisrequiredtoconnecttheinterfacesignalstothestandardsocket.The
tablebelowshowsthepindefinitionsoftheinterfaces.
Pin SignalName Pin SignalName
1 DCD# 2 RXD
3 TXD 4 DTR#
5 GND 6 DSR#
7 RTS# 8 CTS#
COM1/COM2/COM3/COM4
9 RI# 10 NA
Chapter2Installation
EC41812CLDNA 9
2) COM5/COM6: TTL
COM5/COM6 are2×3Pin (0mm)COMdevicepinsandthetablebelowshowsthepin
definitionsoftheinterfaces.
Pin SignalName Pin Si gnalName
1
COM5_TXD/
COM7_TXD
2
COM6_TXD/
COM8_TXD
3
COM5_RXD/
COM7_RXD
4
COM6_RXD/
COM8_RXD
COM5/COM6
5 GND 6 GND
VideoInterface
1） VGADisplayInterface
VGA1 is 2×5Pin (2.0mm) device pin; the transfer cable is required to connect the
interfacesignalstothestandardsocket.Thetablebelowshowsthepindefinitionsof
theinterface.
Pin SignalName Pin SignalName
1 VSYNC 2 HSYNC
3 DDCDATA 4 Red
5 DDCCLK 6 Green
7 +5V 8 Blue
VGA1
9 GND 10 GND
Chapter 2 Installation
10 EC41812CLDNA
2） 36bitDualscan LVDSDisplayInterface
Pindefinitions of LVDS1:
Pin SignalName Pin SignalName
1 LVDS0_D0+ 2 LVDS0_D0
3 GND 4 GND
5 LVDS0_D1+ 6 LVDS0_D1
7 GND 8 GND
9 LVDS0_D2+ 10 LVDS0_D2
11 GND 12 GND
13 LVDS0_CLK+ 14 LVDS0_CLK
15 GND 16 GND
17 NC 18 NC
LVDS1
19 VDD 20 VDD
Pindefinitionsof LVDS2:
Pin SignalName Pin SignalName
1 LVDSE_D0+ 2 LVDSE_D0
3 GND 4 GND
5 LVDSE_D1+ 6 LVDSE_D1
7 GND 8 GND
9 LVDSE_D2+ 10 LVDSE_D2
11 GND 12 GND
13 LVDSE_CLK+ 14 LVDSE_CLK
15 GND 16 GND
17 NC 18 NC
LVDS2
19 VDD 20 VDD
Note: LVDS0xrepresentstheoddlineofdualscan PANEL; LVDSExrepresentsthe
even line of dualscan PANEL. Please connect to LVDS1 if a singlechannel
LCDscreen isused.
Chapter2Installation
EC41812CLDNA 11
Net workInterface
LAN1 is a 2×7Pin (2.0mm) device pin. This pinstyle interface is the
10/100/1000MbpsEthernetportonmotherboardandthetransfercableisrequiredto
connect the interface signals tothestandardsocket. The table below showsthe pin
definitionsoftheinterface.
Pin SignalName Pin SignalName
1 MX0+ 2 MX0
3 MX1+ 4 MX1
5 MX2+ 6 MX2
7 MX3+ 8 MX3
9 GND 10 GND
11 LINK_LED+ 12 LINK_LED
LAN1
13 ACT_LED+ 14 ACT_LED
Whenuse thetransfercabletoconnecttheinterfacesignalstothestandard socketof
RJ45interface. PleaserefertothestatusdescriptionforeachLED asfollow:
LILED
(DualCol or:Y/G)
LANSpeed
Indicator
ACTLED
(SingleGreen)
LANActivity
Indicator
Green 1000Mbps
Flash DataTransmitting Yellow 100Mbps
Off NoDatatoTransmit Off 10Mbps
PowerInterface
PWR1isa1×8Pinpowerdevicepinandthetransfercableisrequiredtoconnectthe
interfacesignalstothestandardsocket.Thetablebelowshowsthepindefinitionsof
theinterface.
Chapter 2 Installation
12 EC41812CLDNA
Pin SignalName Pin SignalName
1 +5V 5 GND
2 +5V 6 GND
3 +5V 7 GND
PWR1
4 GND 8 NC
AudioInterface
AUDIO1isa2×5Pin(2.0mm)audiodevicepinandthetransfercableisrequiredto
connect the interface signals tothestandardsocket. The table below showsthe pin
definitionsoftheinterface.
MultifunctionI nterface
J1isa2×5Pin(2.0mm)devicepin;itisamultifunctioninterfaceandusedtoconnect
withkeyboard, mouse, buzzer andRESET;thetransfercable isrequired toconnect
theinterfacesignalstothestandardsocket.Thetablebelowshowsthepindefinitions
oftheinterface.
Pin SignalName Pin SignalName
1 SPEAK 2 +5V
3 RESET 4 GND
5 KeyboardData 6 KeyboardClock
7 GND 8 Mouse Clock
J1
9 +5V 10 Mouse Data
Pin SignalName Pin SignalName
1 LOUT_R 2 LOUT_L
3 GND_AUDIO 4 GND_AUDIO
5 LIN_R 6 LIN_L
7 GND_AUDIO 8 GND_AUDIO
AUDIO1
9 MIC_L 10 MIC_R
Chapter2Installation
EC41812CLDNA 13
DigitalI/OInterface
GPIO1 isa2×5Pin(2.0mm)digitalI/Ointerface andthetablebelowshows thepin
definitionsoftheinterface.
SATA Interface
TheboardprovidestwostandardSATA interfaces,whichadoptfoolproofdesignand
could be used to connect with SATA hard disk; users shall pay attention to the
directionofthesocketandinsertitgently.Thetablebelowshowsthepindefinitions
oftheinterface,A1~A7areinterfacesforSATAdatacableswhileB1~B15areSATA
powerinterfaces.
Pin SignalName Pin SignalName
A1 GND B5 GND
A2 TX+ B6 GND
A3 TX B7 +5VL
A4 GND B8 +5V
A5 RX B9 +5V
A6 RX+ B10 GND
A7 GND B11 NC
B1 NC B12 GND
B2 NC B13 NC
B3 NC B14 NC
SATA1/SATA2
B4 GND B15 NC
Note: when using onboard SATA power interface to supply power for SATA hard
disk,only2.5″SATAharddiskissupported;whenusingexternalpower,both
2.5″harddiskand3.5″harddiskaresupported.
Pin SignalName Pin SignalName
1 INPUT0 2 OUTPUT0
3 INPUT1 4 OUTPUT1
5 INPUT2 6 OUTPUT2
7 INPUT3 8 OUTPUT3
GPIO1
9 GND 10 NC
Chapter 2 Installation
14 EC41812CLDNA
CF Card
CompactFlashcardisasortofhighspeedmemory,smallinsizeandeasytouse.Its
storagecapacitywillvarywithdifferentcardsinuse,suchas1M,256Metc.CFcard
couldonlyinsertinonedirection(markedasCF1 onthebackofboard).
Pin SignalName Pin SignalName
1 GND 26 NC
2 D3 27 D11
3 D4 28 D12
4 D5 29 D13
5 D6 30 D14
6 D7 31 D15
7 CS0# 32 CS1#
8 GND 33 NC
9 GND 34 IOR#
10 GND 35 IOW#
11 GND 36 WE#
12 GND 37 IRQ
13 VCC 38 VCC
14 GND 39 CSEL#
15 GND 40 NC
16 GND 41 RESET#
17 GND 42 IORDY
18 A2 43 DREQ
19 A1 44 DACK#
20 A0 45 DASP#
21 D0 46 ATA66_DET
22 D1 47 D8
23 D2 48 D9
24 WP/IOCS16# 49 D10
25 NC 50 GND
Chapter2Installation
EC41812CLDNA 15
MiniP CIEInterface
MPCIE1 is a 52Pin wireless network card; the card could only be inserted in one
direction(markedasMPCIE1onboard).Thetablebelowshowsthepindefinitionsof
theinterface.
Pin SignalName Pin SignalName
1 WAKE# 2 3.3V
3 CHANNEL_DATA 4 GND
5 CHANNEL_CLK 6 1.5V
7 CLKREQ# 8 RESERVED_SIM4
9 GND 10 RESERVED_SIM3
11 REFCLK 12 RESERVED_SIM2
13 REFCLK+ 14 RESERVED_SIM1
15 GND 16 RESERVED_SIM0
17 RESERVED0 18 GND
19 RESERVED1 20 RESERVED_DISABLE#
21 GND 22 PERST#
23 PETN0 24 3.3V
25 PETP0 26 GND
27 GND 28 1.5V
29 GND 30 SMB_CLK
31 PERN0 32 SMB_DATA
33 PERP0 34 GND
35 GND 36 USB_D
37 RESERVED_PCIE0 38 USB_D+
39 RESERVED_PCIE1 40 GND
41 RESERVED_PCIE2 42 LED_WWAN#
43 RESERVED_PCIE3 44 LED_WLAN#
45 RESERVED_PCIE4 46 LED_WPAN#
47 RESERVED_PCIE5 48 1.5V
49 RESERVED_PCIE6 50 GND
51 RESERVED_PCIE7 52 3.3V
Chapter 3 BIOS Setup
16 EC41812CLDNA
Chapter3 BIOSSetup
Regarding the BIOS features setup of EC41812CLDNA, please refer to the AMI
BIOSSetupGuide editedbyEVOCCompany.Whilethedifferent part,pleasereferto
thedescriptionsbelow.
When starting up the SETUP program, you may see the main interface of CMOS
SetupUtility asfollows:
BIOSSETUPUTILITY
SystemOverview
Processor
Genuine Intel(R) CPU @ 2.40GHz
Speed :2400MHz
Cores :1
SystemMemory
Size: 504MB
SystemTime [00:47:55]
SystemDate [Wed03/30/2007]
←→ SelectScreen
↑↓ SelectItem
+ ChangeField
Tab SelectField
F1 GeneralHelp
F10 SaveandExit
ESC Exit
V02.57(c)Copyright19852004,AmericanMegatrends,Inc.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

EVOC EC4­1812CLDNA User manual

EVOC
Brand
EVOC
Model
EC4­1812CLDNA
Category
Motherboards
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents