AB-909W
A-Bus Two Zone Audio Kit w/Bluetooth
& 2 pair In-Ceiling Speakers
R
• Intelligent Entertainment • Infrastructure • Security Solutions
C H A N N EL V I S I O N
Pwr
Channel Vision
C H A N N EL V I S I O N
Pwr
Local In
24VDC
AB-412
IR Out
Priority
Loc
Sys
C H A N N E L V I S I O N
2
3
Simplify your installation with this two zone bluetooth audio package. This audio
package allows you to customize individual rooms to give anyone in condos, hotels,
dorm rooms, and bedrooms control over their own smartphone or other streaming
music. The AB-909W Kit includes the (1) AB-412, (2) AB-135W, (1) AB-303 (2) pair
IC608 speakers, and an AB-T2410 power supply.
Product Introduction
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with these
instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. This apparatus must not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Unplug this apparatus during lightning storms or when unused for long
periods of time
Warning: To reduce the risk of electric shock, do not remove the cover (or back),
no user serviceable parts inside, refer servicing to qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
Pwr/Source Button ... Keypad On/Off control and source
selection control when in multi-mode.
Green LEDs...These LED’s illuminate green to
indicate volume level
Volume Controls...
Increase or decrease volume level.
Features:
• Compatible with Channel Vision single source CAT5 audio systems
• Easy to use volume control
Compatibility
How it Works
Basic Operation
The AB-135 is an amplified keypad for single-source CAT5
audio systems. It provides convenient volume control capabilities while its elegant
decorator styling blends seamlessly with other wall switch devices.
Channel Vision’s
The AB-1 adheres
Vision’s other CAT5 audio hubs to ensure maximum
compatibility. Single-source CAT5 audio products from
other manufacturers may not (and typically will not) use the
same control codes for the AB-135 keypad.
35 to the same protocols as Channel
The AB-1 can be used to control a single source with a CAT5 audio hub. T
provides basic controls: volume up, volume down, and power on/off.
35 he unit
Using the AB-135 Amplified keypad...
The Pwr (power) button located at the lower left of the keypad is used to turn the unit
on or off. Press and hold the power button to turn the keypad off.
After volume is changed, the LEDs will stay lit for 5 seconds, showing the current
volume level. Volume adjustments can be made using the up/down buttons to the
right hand side of the keypad.
C H A N NE L V I S I ON
Pwr
Model AB-135W
2
3
Simplify your installation with this two zone bluetooth audio package. This audio
package allows you to customize individual rooms to give anyone in condos, hotels,
dorm rooms, and bedrooms control over their own smartphone or other streaming
music. The AB-909W Kit includes the (1) AB-412, (2) AB-135W, (1) AB-303 (2) pair
IC608 speakers, and an AB-T2410 power supply.
Product Introduction
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this device near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with these
instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. This apparatus must not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Unplug this apparatus during lightning storms or when unused for long
periods of time
Warning: To reduce the risk of electric shock, do not remove the cover (or back),
no user serviceable parts inside, refer servicing to qualified service personnel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
Pwr/Source Button ... Keypad On/Off control and source
selection control when in multi-mode.
Green LEDs...These LED’s illuminate green to
indicate volume level
Volume Controls...
Increase or decrease volume level.
Features:
• Compatible with Channel Vision single source CAT5 audio systems
• Easy to use volume control
Compatibility
How it Works
Basic Operation
The AB-135 is an amplified keypad for single-source CAT5
audio systems. It provides convenient volume control capabilities while its elegant
decorator styling blends seamlessly with other wall switch devices.
Channel Vision’s
The AB-1 adheres
Vision’s other CAT5 audio hubs to ensure maximum
compatibility. Single-source CAT5 audio products from
other manufacturers may not (and typically will not) use the
same control codes for the AB-135 keypad.
35 to the same protocols as Channel
The AB-1 can be used to control a single source with a CAT5 audio hub. T
provides basic controls: volume up, volume down, and power on/off.
35 he unit
Using the AB-135 Amplified keypad...
The Pwr (power) button located at the lower left of the keypad is used to turn the unit
on or off. Press and hold the power button to turn the keypad off.
After volume is changed, the LEDs will stay lit for 5 seconds, showing the current
volume level. Volume adjustments can be made using the up/down buttons to the
right hand side of the keypad.
C H A N NE L V I S I ON
Pwr
Model AB-135W
4
5
Features:
Adds Bluetooth streaming capability to existing or new A-BUS systems
h
Functions as a main or local source
h
Operation:
Plug the AB-303 output (do no use input) into the System Input on the back of the AB-
412. To pair to the AB-303, consult instructions on pairing supplied with your
Bluetooth device. The Bluetooth LIM identification code will have the prefix AB in front
of the individual code number. When pairing occurs, a blue LED will light up on the
front plate. For systems with multiple AB-303s, it is recommended the codes be
changed to easily identify each room before completing installation.
Operating Range:
Bluetooth devices are intended to provide wireless communication between
enabled devices within a room. In ideal conditions, range can be up to 50’
This distance can be reduced significantly by transmission interference from other
communication devices, electrical wiring and room construction materials, such as
brick walls and concrete floors. When the AB-303 is operating near maximum range,
the signal may intermittently drop in and out, as signal strength varies.
Bluetooth Source Volume Level Compatibility:
The audio output level from Bluetooth enabled devices can vary from brand to brand.
Though the AB-303 has been adjusted to be equal to the output of most Bluetooth
devices, in some cases the level may be different. Most devices have their own
adjustable volume level, and it is recommended that this be used to adjust the output
level to match the main audio source’s volume level.
Room Identification:
Pairing each AB-303 requires the identification of an individual code number
beginning with the prefix AB (ABxxx). This code number can be replaced with an
individual room name identification such as Bedroom 1, Study, Patio, etc. prior to
installation. To download the renaming software visit www.a-bus.com/bt. Once
downloaded and installed, connect the AB-303 via the mini USB socket located at
the side of the unit to your PC and start the program, follow the on screen prompts to
rename the device.
The AB-303 A-BUS Bluetooth local input module provides a local wireless input
connection for the purpose of streaming audio from sources such as smart-phones,
tablets and computers, etc with Bluetooth capability to individual A-BUS equipped
rooms. When the AB-303 is paired, it will automatically switch the music source from
the main audio source to the local Bluetooth source. This local connection will remain
until pairing is disconnected, or the Bluetooth device is out of range.
If pairing remains selected on the Bluetooth device, when it comes back into range,
the connection will automatically reconnect and play audio in the zone.
Model AB-303
Model AB-412
Local In
24VDC
AB-412
IR Out
Priority
Loc
Sys
C H A NN E L V I S I ON
TM
The AB-412 functions as the heart of your A-BUS system. It is a 1x2
distribution module that deliver power and audio signals to 2 amplified
keypads (model AB-135).
IR emitter output (not used if using an AB-135)
24VDC power supply
connection (included).
Expansion connector is used to hook up
additional AB-412s.
TM
A-BUS Input from model
AB-203, AB-303, or Expansion
output.
Zone outputs for keypad
connections.
Rear panel connections
Front panel connections
Local Input
Features:
•
• Integrated single source audio input
• A-Bus input from remote room
Fits into a standard 2-gang low voltage ring (not included)
The priority switch determines
which input will be heard (either
TM
A-BUS or Local) when audio is
sensed from both.
Expansion
Out
TM
A-BUS
Input
by
TM
Channel Vision
1-800-840-0288
International Patent Pending
Leisure Tech Electronics Ltd Australia
MADE IN CHINA
AB-412
TM
1x2
A-BUS
Distribution Module
Zone 1
Zone 2
4
5
Features:
Adds Bluetooth streaming capability to existing or new A-BUS systems
h
Functions as a main or local source
h
Operation:
Plug the AB-303 output (do no use input) into the System Input on the back of the AB-
412. To pair to the AB-303, consult instructions on pairing supplied with your
Bluetooth device. The Bluetooth LIM identification code will have the prefix AB in front
of the individual code number. When pairing occurs, a blue LED will light up on the
front plate. For systems with multiple AB-303s, it is recommended the codes be
changed to easily identify each room before completing installation.
Operating Range:
Bluetooth devices are intended to provide wireless communication between
enabled devices within a room. In ideal conditions, range can be up to 50’
This distance can be reduced significantly by transmission interference from other
communication devices, electrical wiring and room construction materials, such as
brick walls and concrete floors. When the AB-303 is operating near maximum range,
the signal may intermittently drop in and out, as signal strength varies.
Bluetooth Source Volume Level Compatibility:
The audio output level from Bluetooth enabled devices can vary from brand to brand.
Though the AB-303 has been adjusted to be equal to the output of most Bluetooth
devices, in some cases the level may be different. Most devices have their own
adjustable volume level, and it is recommended that this be used to adjust the output
level to match the main audio source’s volume level.
Room Identification:
Pairing each AB-303 requires the identification of an individual code number
beginning with the prefix AB (ABxxx). This code number can be replaced with an
individual room name identification such as Bedroom 1, Study, Patio, etc. prior to
installation. To download the renaming software visit www.a-bus.com/bt. Once
downloaded and installed, connect the AB-303 via the mini USB socket located at
the side of the unit to your PC and start the program, follow the on screen prompts to
rename the device.
The AB-303 A-BUS Bluetooth local input module provides a local wireless input
connection for the purpose of streaming audio from sources such as smart-phones,
tablets and computers, etc with Bluetooth capability to individual A-BUS equipped
rooms. When the AB-303 is paired, it will automatically switch the music source from
the main audio source to the local Bluetooth source. This local connection will remain
until pairing is disconnected, or the Bluetooth device is out of range.
If pairing remains selected on the Bluetooth device, when it comes back into range,
the connection will automatically reconnect and play audio in the zone.
Model AB-303
Model AB-412
Local In
24VDC
AB-412
IR Out
Priority
Loc
Sys
C H A NN E L V I S I ON
TM
The AB-412 functions as the heart of your A-BUS system. It is a 1x2
distribution module that deliver power and audio signals to 2 amplified
keypads (model AB-135).
IR emitter output (not used if using an AB-135)
24VDC power supply
connection (included).
Expansion connector is used to hook up
additional AB-412s.
TM
A-BUS Input from model
AB-203, AB-303, or Expansion
output.
Zone outputs for keypad
connections.
Rear panel connections
Front panel connections
Local Input
Features:
•
• Integrated single source audio input
• A-Bus input from remote room
Fits into a standard 2-gang low voltage ring (not included)
The priority switch determines
which input will be heard (either
TM
A-BUS or Local) when audio is
sensed from both.
Expansion
Out
TM
A-BUS
Input
by
TM
Channel Vision
1-800-840-0288
International Patent Pending
Leisure Tech Electronics Ltd Australia
MADE IN CHINA
AB-412
TM
1x2
A-BUS
Distribution Module
Zone 1
Zone 2
Green/White - Left Channel Audio Ground
Green - Left Channel Audio
Orange/White - Right Channel Audio Ground
Blue - IR Signal
Blue/White - Status
Orange- Right Channel Audio
Brown/White 24vDC Ground
Brown 24vDC
Top view:
6
7
System Diagram
Troubleshooting
Problem: Hum in System
Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away.
Try lifting the ground with a ground lifting plug.
Possible Cause: The different components in the system are connected to different electrical
grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz
hum.
Solution: Plug products into an electrical circuit with a common ground.
Problem:
Troubleshooting:
1. Restart Bluetooth source device
2. Check Source device is connected to Wifi
3. Check the music source is active before pairing
4. The blue LED indicates when devices are paired
5. Try a different A-BUS source.
6. Make sure Bluetooth device is in play mode
Not linking with Bluetooth device or Linking with no audio is present.
Problem:
Troubleshooting: Verify you have connected the CAT5 cable correctly. Follow the TIA-568A
standard at both ends. Mis-wiring can cause distorted sound, prevent the system from
functioning, or possibly cause damage to the components in the system. Verify you have
connected the speakers in phase. Follow the label on the product. Out of phase speakers can
rob the system of its bass, especially when driving dual-voice-coil speakers.
If no audio is heard, check to make sure that the audio source is playing, then press the power
button on the AB-135 to make sure it is turned on.
Audio quality issues
Pin-out
Local In
24VDC
AB-412
IR Out
Priority
Loc
Sys
C H A N N EL V ISI O N
Source
C H A N N E L VI S ION
Pwr
Expansion
Out
TM
A-BUS
Input
Zone 1
Zone 2
by
TM
Channel Vision
1-800-840-0288
International Patent Pending
Leisure Tech Electronics Ltd
Australia
MADE IN CHINA
AB-412
TM
1x4 A-BUS
Distribution Module
Power supply
(AB-T2410)
AB-135
AB-135
Receiver
Room 2
Use speaker wire rated for use in walls.
AWG 18 or larger is recommended.
Be sure to wire speakers in phase. +
terminal on the AB-135 to the + or red
terminal on each speaker.
1
2
3
Front
Rear
Room 1
Source
C HA NN EL V ISI ON
Pwr
Cat-5 cables: Use RJ-45 connectors that are wired for the TIA568A
standard. (Using the TIA568B wiring configuration will work, but the left and
right audio information will be reversed).
Expansion Output: Use this to expand to an additional AB-412. This
connector only provides audio signals to an additional AB-412. It cannot be
used to directly connect a 3rd AB-135 to the system.
Volume indicators: The LEDs indicate the volume level. If the Status is
<off>, the LEDs will be dark. Pressing the UP/DOWN keys will light the
LEDs for a short period to show the stored volume level.
1
2
3
Problem: CAT5 audio input (AB-303 or other device) is not working.
Troubleshooting: Verify you have plugged the CAT5 output on the AB-303 or other A-Bus input
module into the input on the back of the AB-412. Verify you have plugged the zone 1 or zone 2
output of the AB-412 into the input on the back of the AB-135.
Possible Cause: AB-303 or other A-Bus input module is not connected properly, wire crimped
improperly or plugged into the wrong terminal.
Solution: Verify wiring, verify RJ-45 crimps
Problem: RCA Audio input is not working.
Troubleshooting: Verify source audio is playing, or try another audio source Check speaker
wires to verify nothing is backwards or crossed.
Possible Cause: There is no signal (or very weak signal) coming from the source, or source is
not compatible with AB-412
Solution: Make sure the source audio is playing. Try a different source.
AB-303
Green/White - Left Channel Audio Ground
Green - Left Channel Audio
Orange/White - Right Channel Audio Ground
Blue - IR Signal
Blue/White - Status
Orange- Right Channel Audio
Brown/White 24vDC Ground
Brown 24vDC
Top view:
6
7
System Diagram
Troubleshooting
Problem: Hum in System
Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away.
Try lifting the ground with a ground lifting plug.
Possible Cause: The different components in the system are connected to different electrical
grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz
hum.
Solution: Plug products into an electrical circuit with a common ground.
Problem:
Troubleshooting:
1. Restart Bluetooth source device
2. Check Source device is connected to Wifi
3. Check the music source is active before pairing
4. The blue LED indicates when devices are paired
5. Try a different A-BUS source.
6. Make sure Bluetooth device is in play mode
Not linking with Bluetooth device or Linking with no audio is present.
Problem:
Troubleshooting: Verify you have connected the CAT5 cable correctly. Follow the TIA-568A
standard at both ends. Mis-wiring can cause distorted sound, prevent the system from
functioning, or possibly cause damage to the components in the system. Verify you have
connected the speakers in phase. Follow the label on the product. Out of phase speakers can
rob the system of its bass, especially when driving dual-voice-coil speakers.
If no audio is heard, check to make sure that the audio source is playing, then press the power
button on the AB-135 to make sure it is turned on.
Audio quality issues
Pin-out
Local In
24VDC
AB-412
IR Out
Priority
Loc
Sys
C H A N N EL V ISI O N
Source
C H A N N E L VI S ION
Pwr
Expansion
Out
TM
A-BUS
Input
Zone 1
Zone 2
by
TM
Channel Vision
1-800-840-0288
International Patent Pending
Leisure Tech Electronics Ltd
Australia
MADE IN CHINA
AB-412
TM
1x4 A-BUS
Distribution Module
Power supply
(AB-T2410)
AB-135
AB-135
Receiver
Room 2
Use speaker wire rated for use in walls.
AWG 18 or larger is recommended.
Be sure to wire speakers in phase. +
terminal on the AB-135 to the + or red
terminal on each speaker.
1
2
3
Front
Rear
Room 1
Source
C HA NN EL V ISI ON
Pwr
Cat-5 cables: Use RJ-45 connectors that are wired for the TIA568A
standard. (Using the TIA568B wiring configuration will work, but the left and
right audio information will be reversed).
Expansion Output: Use this to expand to an additional AB-412. This
connector only provides audio signals to an additional AB-412. It cannot be
used to directly connect a 3rd AB-135 to the system.
Volume indicators: The LEDs indicate the volume level. If the Status is
<off>, the LEDs will be dark. Pressing the UP/DOWN keys will light the
LEDs for a short period to show the stored volume level.
1
2
3
Problem: CAT5 audio input (AB-303 or other device) is not working.
Troubleshooting: Verify you have plugged the CAT5 output on the AB-303 or other A-Bus input
module into the input on the back of the AB-412. Verify you have plugged the zone 1 or zone 2
output of the AB-412 into the input on the back of the AB-135.
Possible Cause: AB-303 or other A-Bus input module is not connected properly, wire crimped
improperly or plugged into the wrong terminal.
Solution: Verify wiring, verify RJ-45 crimps
Problem: RCA Audio input is not working.
Troubleshooting: Verify source audio is playing, or try another audio source Check speaker
wires to verify nothing is backwards or crossed.
Possible Cause: There is no signal (or very weak signal) coming from the source, or source is
not compatible with AB-412
Solution: Make sure the source audio is playing. Try a different source.
AB-303
500-373 rev A
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Tested To Comply
With FCC Standards
A-BUS is a registered trademark of LeisureTech Electronics Pty Ltd.
This product may be covered by one of the following patents:
US patent no. 7,181,023, 6,389,139 EP 1004222, AU 739808, NZ 502982, Mexico Z41196, Canada
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: [email protected]
• Intelligent Entertainment • Infrastructure • Security Solutions
www.channelvi s i o n . c o m
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs
during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from
the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This
warranty does not cover damages in shipment, failures caused by other products not supplied by
Channel Vision Technology, or failures due to accident, misuse, abuse, acts of God, or alteration of the
equipment. This warranty is extended only to the original purchaser when purchased through an
authorized reseller. A purchase receipt, invoice, or other proof of original purchase date will be required
before warranty repairs are provided. Mail in service can be obtained during the warranty period by
calling (714) 424-6500. A Return Authorization number must be obtained in advance and can be marked
on the outside of the shipping carton. This warranty gives you specific legal rights and you may have
other rights (which vary from state to state). If a problem with this product develops during or after the
warranty period, please contact Channel Vision Technology, your dealer or any factory-authorized
service center. Channel Vision products are not intended for use in medical, lifesaving, life sustaining or
critical environment applications. Channel Vision customers using or selling Channel Vision products for
use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any
damages resulting from such improper use or sale.
One Year Limited Warranty
AB-135, AB-412 & AB-303 Specifications: (typical at 77º)
Operating Voltage: 24VDC 1 Amps (one keypad)
Cable requirements: CAT5 or CAT6
Speaker impedance: 6-8 ohm (max two speakers per AB-135)
IR repeating: 30-60kHz
IR sensor range: 40’@40kHz, 25’@56kHz
Operating Temperature: -10ºC to +50ºC
Line Level input (AB-203): Max 1VRMS
IC608 Specifications: (typical at 77º)
Frequency range: 60Hz - 20kHz ± 3dB
Power Handling: 120 Watts
Drivers: 1- 0.5” High compliance polymer
1- 6.5” Polypropylene woofer
Impedance: 8 ohms
Finish: ABS plastic
Dimensions: 9” OD. 3.15
Hole size: 7.7”
*Specifications subject to change without notice
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Channel Vision AB-T2410 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Channel Vision IC608 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
BAZZ 303-600 Operating instructions
-
Black Box EYN7001RD-1000 Datasheet
-
Xantech D5XH User manual
-
AMBIEN TECH STCV-SA-A-96-XXX Installation guide
-
Fender Showman 412S loudspeakers Enclosed Owner's manual
-
-
Aria A0325 Instructions Manual
-
Legrand Multi-Button Low Voltage Switches Installation guide
-
Audioplex JB-2 Quick start guide
-
Cambridge Audio 640r User manual