CLS Emerald M Office Owner's manual

Brand
CLS
Model
Emerald M Office
Type
Owner's manual

This manual is also suitable for

www.cls-led.com www.cls-led.com
h
Ceiling 12,5 cm -
20 cm
15 - 20 cm 150 cm Various
Weights
50.000 h 50º or 71º 60º or 83º IP40
4000K
CRI>92
4000K
CRI>80
Max.
350 mA
Max.
500 mA
Max.
700 mA
Max.
1000 mA
Max.
41 Watt
Max.
28 Watt
Max.
20 Watt
Max.
15 Watt
Phase
dimmable
1-10V
dimmable
ø
21 - 25 cm
ø
3000K
CRI>92
2700K
CRI>80
2700K
CRI>92
3500K
CRI>92
3000K
CRI>80
DRIVER
INCLUDED
DRIVER
EXTERNAL
2500K
CRI>80
2
CLS EMERALD SERIESCLS EMERALD SERIES
Manual V2.6 - February 2021
INDEX
Index 2
Safety information 2
Content 2
Technical 3
Specifications 4
CONTENT
SAFETY INFORMATION
Always switch o mains power
of the driver before connecting
or maintaining any fixtures!
Qualified
technician
Ambiance
Max. 40º
Do not stare
into the LED
Block access
below the work
area when
maintaining
the unit
Use a source
of AC power
that complies to
local electrical
codes
Make sure all
connectors are
connected
properly
Don’t install in
a flammable
or explosive
area
Warning!
Some surfaces
can be hot
Don’t modify
or install
genuine parts
on this product
Assembly 5
Installation 6
Wiring diagram uni non dim driver 7
Wiring diagram uni DALI dim driver 7
Wiring diagram Mains dim driver 9
Wiring diagram 1-10V dim driver 9
Wiring of the LDC-407 driver 10
Programming 10
Programming table 11
List of symbols 12
h
Ceiling 12,5 cm -
20 cm
15 - 20 cm 150 cm Various
Weights
50.000 h 50º or 71º 60º or 83º IP40
4000K
CRI>92
4000K
CRI>80
Max.
350 mA
Max.
500 mA
Max.
700 mA
Max.
1000 mA
Max.
41 Watt
Max.
28 Watt
Max.
20 Watt
Max.
15 Watt
Phase
dimmable
1-10V
dimmable
ø
21 - 25 cm
ø
3000K
CRI>92
2700K
CRI>80
2700K
CRI>92
3500K
CRI>92
3000K
CRI>80
DRIVER
INCLUDED
DRIVER
EXTERNAL
2500K
CRI>80
www.cls-led.com www.cls-led.com
3 4
ø 260 mm
ø 205 mm
131 mm
ø 205 mm
71 mm106 mm
ø 205 mm
ø 260 mm
ø 260 mm
121 mm 86 mm
146 mm
Emerald M Emerald L
Light engine
5 serie - Max. 20 Watt
6 serie - Max. 28 Watt
5 serie - Max. 20 Watt
6 serie - Max. 28 Watt
5 serie - Max. 20 Watt
6 serie - Max. 28 Watt
4 serie - Max. 15 Watt
4 serie - Max. 15 Watt 4 serie - Max. 15 Watt
7 serie - Max. 41 Watt
7 serie - Max. 41 Watt 7 serie - Max. 41 Watt
Ø150 - 200 mm
Cut-out size Ø210 - 250 mm
Cut-out size
TECHNICAL SPECIFICATIONS
Emerald 4 serie
LED: High Power LED
Available colours: CRI>80: 2500K, 2700K, 3000K & 4000K
Beam angle: 50º or 71º
Power supply: Max. 350mA
Power consumption: Max. 15 Watt
Housing: PC / aluminium
Weight: Emerald M: 246 gr
Emerald L: 336 gr
IP value: IP40
Measurements: Emerald M: 71 x 205 mm (hxø)
Emerald L: 86 x 260 mm (hxø)
Ambient temperature: -10º C till +40º C
Emerald 5 serie
LED: High Power LED
Available colours: CRI>80: 2500K, 2700K, 3000K & 4000K
Beam angle: 50º or 71º
Power supply: Max. 500mA
Power consumption: Max. 20 Watt
Housing: PC / aluminium
Weight: Emerald M: 324 gr
Emerald L: 464 gr
IP value: IP40
Measurements: Emerald M: 106 x 205 mm (hxø)
Emerald L: 121 x 260 mm (hxø)
Ambient temperature: -10º C till +40º C
Emerald 7 serie
LED: High Power LED
Available colours: CRI>80: 2500K, 2700K, 3000K & 4000K
CRI>92: 2700K, 3000K, 3500K & 4000K
Beam angle: 60º or 83º
Power supply: Max. 1000mA
Power consumption: Max. 41 Watt
Housing: PC / aluminium
Weight: Emerald M: 484 gr
Emerald L: 570 gr
IP value: IP40
Measurements: Emerald M: 131 x 205 mm (hxø)
Emerald L: 146 x 260 mm (hxø)
Ambient temperature: -10º C till +40º C
Emerald 6 serie
LED: High Power LED
Available colours: CRI>80: 2500K, 2700K, 3000K & 4000K
CRI>92: 2700K, 3000K, 3500K & 4000K
Beam angle: 60º or 83º
Power supply: Max. 700mA
Power consumption: Max. 28 Watt
Housing: PC / aluminium
Weight: Emerald M: 324 gr
Emerald L: 464 gr
IP value: IP40
Measurements: Emerald M: 106 x 205 mm (hxø)
Emerald L: 121 x 260 mm (hxø)
Ambient temperature: -10º C till +40º C
Tools
ø 150 - 200 mm / 210 - 250 mm
www.cls-led.com www.cls-led.com
65
1
3
2
4
Cone
Diusion lter
Oce lens*
Light engine
Make sure that
the shaped surface is
facing downwards
before
assembling
* Only included by the Emerald Oce series
Remove safety
foil from the
diusion lter
before
assembling
ASSEMBLY
2021 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all aliated companies disclaim
liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to
use or reliance on the information contained in this manual. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from CLS-LED BV. Other legal information can be found in our General conditions, found on the back of
your CLS-LED BV invoice, inside the CLS catalogue or on our website www.cls-led.com/General-Terms.pdf
Emerald M ø 150 mm - max. ø 200 mm
Emerald L ø 210 mm - max. ø 250 mm
Minimal
Built-in height
2
34
1
Suspended
ceiling
See step 1
for the minimal
built-in height,
required for
ventilation
Type Emerald M Emerald L
4 serie 125 mm 140 mm
5 serie 160 mm 175 mm
6 serie 160 mm 175 mm
7 serie 185 mm 200 mm
Minimal built-in height
Drivers (included)
Emerald 4 serie - Max. 15 Watt
Emerald 5 serie - Max. 20 Watt
Emerald 6 serie - Max. 28 Watt
Emerald 7 serie - Max. 41 Watt Emerald 4-7 series
130 x 42 x 30 mm
(hxwxd)
130 x 76 x 30 mm
(hxwxd)
222 x 50 x 35 mm
(hxwxd)
Ceiling panel
thickness
max. 20 mm
INSTALLATION
www.cls-led.com www.cls-led.com
7 8
WIRING DIAGRAM UNI NON DIM DRIVER
CLS ND UNI NON DIM
* 150 cm cable
Installation wire 2 x 0.5 mm2
Driver till last Emerald total cable length is max. 10 m
120 ~180 cm cable
120 ~ 180 cm cable
146,5 mm
22 mm
CLS Emerald
# E-X-XX-XX-X
LED engine Min. Max.
4 serie 1 2
5 serie 1 2
6 serie 1 1
7 serie 1 1
A
mount of Emerald xtures on the CLS ND UNI non dim
CLS ND UNI, non dim, 300-1050mA driver
22 x 146,5 x 43,5 mm (hxwxd)
CLS DD UNI DALI
* 150 cm cable
Installation wire 2 x 0.5 mm2
Driver till last Emerald total cable length is max. 10 m
120 ~180 cm cable
120 ~ 180 cm cable
146,5 mm
44 mm
CLS Emerald
# E-X-XX-XX-X
LED engine Min. Max.
4 serie 1 1
5 serie 1 1
6 serie 1 1
7 serie 1 1
A
mount of Emerald xtures on the CLS DD UNI DALI dim
CLS DD UNI DALI, DALI dim, 300-1050mA driver
30 x 146,5 x 44 mm (hxwxd)
Always switch off mains power of the driver before connecting any fixtures!
WIRING DIAGRAM UNI DALI DIM DRIVER
WIRING DIAGRAM MAINS DIM DRIVER
* 150 cm cable
Installation wire 2 x 0.5 mm2
Driver till last Emerald total cable length is max. 10 m
120 ~180 cm cable
CLS Dimmer Jung phase cut
max. 270VA 230-240VAC
# 872019
80,5 mm (w)
80,5 mm (h)
L
N
Max. 12 pieces of MD 004 on
1 CLS dimmer Jung phase-cut
CLS MD 004
46 mm
166 mm
CLS Emerald
# E-X-XX-XX-X
LED engine Min. Max.
M4 1 1
M5 1 1
M6 1 1
M7 - -
Amount of Emerald fixtures on the CLS MD 004
CLS MD 004, mains dimmable, 250-700mA driver
34 x 166 x 46 mm (hxwxd)
Installation wire 2 x 0.5 mm2
Driver till last Emerald
total cable length is max. 10 m
CLS VD 001
0-10 V
80,5 mm (w)
80,5 mm (h)
CLS Dimmer electr. 1-10V
# 872010
L
N
120 ~180 cm cable
* 150 cm cable
Max. 12 pieces of VD 001 on
1 CLS Dimmer electr. 1-10V
52 mm
100 mm
CLS Emerald
# E-X-XX-XX-X
LED engine Min. Max.
M4 1 1
M5 1 1
M6 - -
M7 - -
Amount of Emerald fixtures on the CLS VD 001
CLS VD 001, 1-10V dimmable, 350-900mA driver
22 x 100 x 52 mm (hxwxd)
Always switch off mains power of the driver before connecting any fixtures!
WIRING DIAGRAM 1-10V DIM DRIVER
www.cls-led.com www.cls-led.com
9 10
Installation wire 2 x 0.5 mm2
Driver till last Emerald
total cable length is max. 10 m
0-10 V
80,5 mm (w)
80,5 mm (h)
CLS Dimmer electr. 1-10V
# 872010
L
N
120 ~180 cm cable
* 150 cm cable
Max. 12 pieces of VD 004 on
1 CLS Dimmer electr. 1-10V
CLS VD 004
67 mm
100 mm
CLS Emerald
# E-X-XX-XX-X
LED engine Min. Max.
M4 1 1
M5 1 1
M6 1 1
M7 - -
Amount of Emerald fixtures on the CLS VD 004
CLS VD 004, 1-10V dimmable, 350-900mA driver
21 x 103 x 67 mm (hxwxd)
120 ~180 cm cable
Max. 12 pieces of VD 008 on
1 CLS Dimmer electr. 1-10V
CLS VD 008
Installation wire 2 x 0.5 mm2
Driver till last Emerald
total cable length is max. 10 m
0-10 V
80,5 mm (w)
80,5 mm (h)
CLS Dimmer electr. 1-10V
# 872010
L
N
* 150 cm cable
79 mm
124 mm
LED engine Min. Max.
M4 1 2
M5 1 2
M6 1 1
M7 - -
Amount of Emerald fixtures on the CLS VD 008
CLS Emerald
# E-X-XX-XX-X
CLS VD 008, 1-10V dimmable, 250-700mA driver
22 x 124 x 79 mm (hxwxd)
Always switch off mains power of the driver before connecting any fixtures!
WIRING DIAGRAM 1-10V DIM DRIVER WIRING OF THE LDC-407 DRIVER
PROGRAMMING
123
* If the LEDs ashes 10 times, something went wrong. Please try again. If the problem continues to occur, please contact your local sales distributor.
Place magnet
at the bottom
of the LDC-407.
The LED of the
Mika will
light up
After 2 seconds
the LED will ash
3 times
conrming
storage*
All settings can be configured via DMX. Settings can be configured at once or separately. When one or a couple settings needs to be
changed just leave all other setting values zero. This keeps those settings unchanged. Please check the table for more information.
Always use a DMX controller with digital interface. If not available, you can purchase the CLS D-ta DMX addresser unit (
#122200
).
First make sure to set the DATA on the DMX controller. To program the setting into the LED fixture follow the next steps.
www.cls-led.com www.cls-led.com
11 12
PROGRAMMINGTABLE
DMX
Function
Data
Parameters
CH1
Setaddress
001to255
0
0=nochange
1…255
DMXaddress=1…255
CH2
Setaddress
256to508
0
nochange
1…255
DMXaddress=256…508
CH3 Static
behavior
0
nochange
IfnoDMXispresentthefixturewillrespondlike
setinthisfunction.
1
lastDMXvalue
2
outputoff
3
loadstaticvalues
CH4 Softdim
0
nochange
values.Thisfunctionmakesthedimcurve
1
off
2
on
CH5 Master
control
0
nochange
Ifmasterisfirstchannelisselectedthechannel
willbeDMXchannel“n”.Ifmasterislastchannel
isselectedthechannelwillbe“n+x”
1
nomasterused
2
masterisfirstchannel
3
masterislastchannel
CH6 Output1
patch
0
nochange
Eachoutputchannelcanbepatchedtorespond
tothedesiredDMXchannel.Thisenablesthe
usertomixupthecoloursaccordingtothe
controllerthatisused.
Example:alloutputsarepatchedas1
AlloutputswillbecontrolledbyDMXchannel
“n”.IfmasterisusedtotalDMXchannelswillbe2
otherwiseituses1channel(“x”=1).
Example:output1&2arepatchedas1and3&4
arepatchedas2
Output1&2willbecontrolledbyDMXchannel
“n”.
Output3&4willbecontrolledbyDMXchannel
“n+1”.
IfmasterisusedtotalDMXchannelswillbe3
otherwiseituses2channels(“x”=2).
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH7Output2
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH8 Output3
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH9Output4
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH10Staticoutput
1
0
nochange
Eachoutputchannelcanbesettoanstatic
intensity.
IfnoDMXispresentandStaticbehaviorissetto
“loadstaticvalues”.Theoutputswillbesettothe
configuredintensityvalues.
1
outputoff
2…255
intensity2…255
CH11Staticoutput
2
0
nochange
1
outputoff
2…255
intensity2…255
CH12Staticoutput
3
0
nochange
1
outputoff
2…255
intensity2…255
CH13Staticoutput
4
0
nochange
1
outputoff
2…255
intensity2…255
CH14Loaddefault
settings
0
nochange
ThisfunctionresetsallsettingstotheFactory
setting.CheckFactorysettingtable.
X
LoadFactorysettings.Xisrow
numberfactorysettingtable.
PROGRAMMING TABLE LIST OF SYMBOLS
Multiple connection
Daisychain connectivity
Installation depth
In centimeters
Swivel
Fixture is horizontally rotatable,
indicated in degrees
Swivel
Fixture is vertically rotatable,
indicated in degrees
Installation size
In centimeters
Application area
Indoor or outdoor
Application area
Floor, wall or ceiling
Protection class
One, two or three
Cable length
Maximum cable attached
to the fixture in centimeters
Lifespan
Of the light source in hours
Driver
Inclusive or exclusive
Internal or external
Pressure
Maximum pressure on the
fixture in kg/cm2
Weight
In grams/kilograms
Curve
Minimal bending curve
in centimeters
LED pitch
Pitch between the LEDs
in millimeters
Power supply
In VDC, VAC or milliAmpere
Power consumption
In VA or Watt
IP value
Ingress Protection classifies the
degrees of protection provided against
the intrusion of the product
Cutting length
Indicated by the cutting
marks
LEDs
Kind of LED used in the
fixture
Lenses
Availble lenses,
indicated in degrees
Performance Zoom
Adjustable beam angle
Plug & play
Easy connection using the
SmartConnect system
White colour temperature
In dierent Kelvin values;
Cold white, neutral white, warm
white or extra warm white
Colour
Available colours;
Amber, blue, red or green
Colour changing
RGB, RGB-W, RGB-A,
AWB or Tunable White
DMX input
Fixture works on DMX512
protocol or Wireless DMX
Magno dimming
Accurate dimming from
100 - 1% by using a magnet
Dynamic Control
Dynamic Power Control or
Dynamic Temperature Control
Combined product
Compose your own fixture
Warranty
3 or 5 years warranty on
the product
Energy label
Conformité Européenne
CE marking for free marketability
of industrial goods within the EU
r
h
ø w d
Dimmable
1-10 Volt, Phase, individual,
DMX dimmable or DALI
DRIVER
INCLUDED
DRIVER
EXTERNAL
Retail & Food LED modules
Clothing, furniture, kitchens, jewellery,
shoes, bread, meat, fish and
vegetables & fruit.
Lightsource
Equipped with a CLS, Citizen or a Xicato
LED module
Bluetooth controlled
By Casambi
PWM dimming
Traditional PWM dimming, DMX analog
or DMX Hybrid dim
CLS
DYNAMIC
COLOUR
COB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

CLS Emerald M Office Owner's manual

Brand
CLS
Model
Emerald M Office
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents