RC Logger NovaX 350 89132RC Installation guide

Brand: RC Logger

Model: NovaX 350 89132RC

Category: Strip lights

Type: Installation guide

RC Logger NovaX 350 89132RC lets you add illumination to the NovaX 350 drone, enhancing its visibility during night flights and adding visual effects controlled via the RC Logger EyeControl app. With multiple lighting modes and color customization options, you can personalize your drone's appearance and create stunning light shows. Installation requires some technical skill, such as removing propellers and the flight battery, and careful handling of electronic components. The kit includes LED strips, a controller board, plastic strip covers, and installation instructions.

NovaX Illumination Kit

No. 89132RC

INTENDED USE

Please download the latest version of the installation

instructions from our website at www.rclogger.com. Navigate

to the product page and open the ”Downloads” tab. Click on

”Operating instructions” to start the download.

Make this product available to third parties only together

with its installation instructions.

The Illumination Kit not only makes your NovaX 350 visible in the dark but also comes

with an array of visual effects that add special interest to your model, controlled via the RC

Logger EyeControl app.

Any use other than the one described can damage the product. Moreover, this involves

dangers such as short circuit, re and electric shock, etc. Observe the safety information

under all circumstances! The product must not become damp or wet.

For safety and approval purposes (CE), you must not rebuild and/or modify this product.

If you use the product for purposes other than those described above, the product may

be damaged. In addition, improper use can cause hazards such as short circuiting, re,

electric shock etc. Read the instructions carefully and keep them.

DELIVERY CONTENT

> LED controller board

> 2x LED strip (front motor arms)

> 2x LED strip (rear motor arms)

> 4x LED strip cover (plastic)

> Installation instructions

WHAT YOU NEED

> NovaX 350 with latest rmware for Illumination Kit (read installation instructions)

> Pair of tweezers

> iOS or Android device with latest EyeControl App for Illumination Kit (read installation

instructions)

SAFETY INSTRUCTIONS

Read the installation instructions carefully and especially

observe the safety information. If you do not follow the

safety instructions and information on proper handling in

these instructions, we assume no liability for any resulting

personal injury or damage to property. Such cases will

invalidate the warranty/guarantee.

If necessary, consult the »NovaX 350 manual for

instructions on how to attach, connect and operate

accessories. Mind the max. takeoff weight.

> The product is not a toy. Keep it out of the reach of children and pets.

> Do not leave packaging material lying around carelessly. These may become

dangerous playing material for children.

> Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

> Do not use the product in rain.

> Do not place the product under any mechanical stress.

> If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed if the

product:

» is visibly damaged,

» is no longer working properly,

» has been stored for extended periods in poor ambient conditions or

» has been subjected to any serious transport-related stresses.

> Please handle the product carefully. Jolts, impacts or a fall even from a low height can

damage the product.

Installation instructions

NovaX 350 with installed 89132RC Illumination Kit. Refer to detailed instructions for installation.

These installation instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower

2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation

reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing

systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. The installation

instructions reect the current technical specications at time of print.

INSTALLATION

For your safety, remove the propellers and the flight battery

before you start the installation.

Study the installation images on the following page before

you start the installation process.

Preparation

1. Remove the ight battery from the NovaX 350.

2. Remove the propellers from the NovaX 350.

3. Carefully remove the canopy from the NovaX 350.

4. Unpack the LED strips and place them on a soft surface. Make sure to discharge

yourself by touching a metal surface before touching the LED board (and the PCB

boards on the NovaX 350). Keep the LED board in the protective bag until you need it.

Guiding the LED strips through the ESC holders

Note: The LEDs must point down (towards the skids). Therefore, when mounted, the

L-shaped strip attached to the LED strip supplying the LEDs with power is located on the

left of the motor arm (when looking at the propeller. This applies to all 4 motor arms and

LED strips.

5. Match the red LED strips with the red legs and the black strips with the black legs.

6. Start on one motor arm. Turn the strip so that LEDs face down. Guide the L-shaped

strip through the lower opening of the ESC holder along the inside of the ESC up to the

ight controller board. A pair of tweezers signicantly eases the process of inserting

the strips. [ 1 ]

7. Repeat the previous step for the three remaining LED strips.

Installing the LED board

8. On the NovaX 350, carefully detach the ight controller board (the top most PCB

board) from the rubber dampers.

9. Fold the controller board with protective sheet underneath up towards the model’s

nose. You may use a long piece of tape, attach it to the edge of the controller board and

secure it on the working surface in order to keep the board folded up. [ 2 ]

10. Unwrap the LED board.

11. Unlock all four FPC connectors by pulling the black locking mechanisms out. Later

you will insert and secure the ends of the L-shaped strips in the FPC connectors. [ 3 ]

12. Remove the protective foils from (1) LED connector and (2) from all four double-sided

tape pieces. [ 3 ]

13. Hold the LED controller board on its edges and insert the corresponding strip ends into the

FPC connectors. Important! Ensure that the contacts face up. After inserting a strip end,

lock the FPC connector by pushing the locking mechanism in. [ 4 ]

[ 5 ]

14. Connect the LED board to the connector LED_BOARD on the power board. After

connecting, apply a little weight to the LED board to make it stick on the power board.

[ 5 ]

15. Carefully remove the tape from the ight controller board that secured the board in its

folded-up position. Lower the ight controller board with protective sheet.

16. Insert the rubber dampers into the holes in the ight controller board again. Important!

The ight controller board must be able to move freely. Remove obstructions if

necessary. [ 6 ]

Finalizing installation

17. Install the canopy.

18. Remove the adhesive protective foil from the LED strips and stick the strips to the

ellipticals (arm supports). [ 7 ]

19. Cover the LED strips with the supplied plastic strip covers. Remove the protective foil

from the adhesive tape. With the side with tape facing the motor, open the plastic cover

and slide it over the LED strip. Repeat this process for the three remaining arms. [ 8 ]

UPGRADING THE FIRMWARE

20. Your NovaX 350 must run at least rmware version FW v1.5 in order for you to use the

night ying kit functions. Refer to the NovaX 350 instruction manual for details on updating

the rmware.

21. Download the latest version of the EyeControl app from Google Play Store or Apple

App Store respectively.

FUNCTION TEST

Refer to the NovaX 350 operating instructions if needed.

22. Turn on the transmitter that is bound to your NovaX 350.

23. Install the ight battery.

24. All four LED strips emit one white ash.

25. Open the EyeControl app on your mobile device and pair it with the NovaX 350.

26. Tab on “ILLUMINATION KIT” and on any lighting mode in “CONTROL PANEL”. LED

strips should light up accordingly.

27. Make desired adjustments and save settings by touching “DONE”.

28. As a last step, mount the propellers again.

29. Installation and testing of the Illumination Kit is completed.

CLEANING AND CARE

> The product does not require any maintenance, do not disassemble it. Maintenance or

repairs may be carried out by a professional only.

> Do not immerge the LED strips in water.

> Clean with a clean, soft, dry cloth only.

> Do not use any aggressive cleaning agents or chemical solutions as these may

damage the housing causing discoloration and/or malfunction.

DISPOSAL

In order to preserve, protect and improve the quality of environment, protect

human health and utilise natural resources prudently and rationally, the user

should return unserviceable product to relevant facilities in accordance with

statutory regulations. The crossed-out wheeled bin indicates the product needs

to be disposed separately and not as municipal waste.

Consequently you comply with your legal obligations and contribute to environmental

protection!

PRODUCT SUPPORT

Visit http://www.rclogger.com/support or call +852 2559 2662 for product support.

Additionally visit our Online Ticket System at http://support.rclogger.com for any RC

Logger inquiry.

TECHNICAL DATA

Power supply ...............................................12 V/DC ±10 %, max. 500 mA

Firmware required .......................................NovaX 350 FW v1.5 or higher

Operating temperature ................................-10 to 55 °C

Operating humidity ......................................10 – 90 % RH

Dimensions .................................................. Control board: 37 x 46 x 4.6 mm

LED strip: 192 x 28 x 1.9 mm

Plastic strip cover: 123 x 15 x 11 mm

Weight .........................................................approx. 52 g

7 8

RC Logger NovaX 350 89132RC Installation guide

Brand: RC Logger

Model: NovaX 350 89132RC

Category: Strip lights

Type: Installation guide

Download PDF

report

RC Logger NovaX 350 89132RC Installation guide

RC Logger NovaX 350 89132RC Installation guide

Related papers

Other documents