ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
Page 1 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tools Required: Power screwdriver; Allen key set (provided)
2 persons required for installation
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
Table top x2
Leg Quadro A x2
Connector frame x1
Beam x2
Plastic bracket x8
A
B
C
D
E
Allen key x2K
M8x20MM CSK x4
M8x20MM Socket head x4
M6x20MM Socket head x8
M6x30MM Socket head x8
M6x30mm Mushroom head screw x4
F
G
H
I
J
COMPONENTS
SCREWS
Page 2 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
D
E
F
G H I J
A
C
B
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Page 3 of 8
Insert the bottom of the legs as shown in the
illustration. Using Allen Key provided, attach
Mushroom Head Screw (J) - for all legs.
You will notice two colored
stickers located on each leg.
Both legs must have the colour
sticker facing away from where
the plastic brackets are inserted.
Plastic bracket holes
facing to the other side.
STEP 01 STEP 02
J
G
H
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
STEP 03
Using Allen Key provided, attach 2 plastic brackets per leg (E)
(as per picture above) using M6x20MM (H) Socket head screw.
Do the same with Connector frame (C).
Using Allen Key provided, attach M8x20MM Socket head (G)-
screw socket half way into leg for both legs (B) and into
Connector frame (C).
STEP 04
Page 4 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
STEP 05
Adjust extendable beam (D) to desired
length using markers and secure beam
at that length using screws provided
Page 5 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
50
1200
1300
1400
1500
1600
1700
1800
1900
2000
50
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
STEP 06
TOP VIEW
Attach beam (D) to legs (B) and Connector frame (C)
using nut insert in legs. See point attached
Frame looks like this. Using Allen Key, attach beam (D) with Socket (F)
STEP 07
Page 6 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
F
F
F
F
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
STEP 08
Page 7 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Place desktops ontop of frame - with cutout at the back of the desk.
Nut inserts in top will align with plastic joiner brackets using M6x30MM
(I) sockets attached tops to frame.
I
TABLE TOP
BOTTOM VIEW
ASSEMBLY INSTRUCTIONS
Quadro Wood A
2P Run workstation
Sizes: 1200, 1400, 1600, 1800 mm
Page 8 of 8
Need help!
Call us on
1300 527 665
www.jasonl.com.au
TABLE TOPS
BOTTOM VIEW
The following nut inserts should be used for this specific desk / workstation
nut insertnut insert nut insertnut insert
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
JasonL QDWR2128.W.WT Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
JasonL QDSR2128.W.WT Operating instructions
-
JasonL QDWB2836.B.WT2 Operating instructions
-
JasonL QDWR3128.W.WT Operating instructions
-
JasonL QDWR2147.W.WT Operating instructions
-
JasonL HQSR3168.W.WT.GS Operating instructions
-
JasonL HQSR2148.B.WT.AB Operating instructions
-
JasonL QDLR3128.W.WT Operating instructions
-
JasonL QDLR2128.W.WT Operating instructions
-
JasonL QDLR3167.W.WT Operating instructions
-
JasonL QDPR3188.W.WT Operating instructions
