Vaxcel W0079 Operating instructions

Brand
Vaxcel
Model
W0079
Category
Wall & ceiling mounts accessories
Type
Operating instructions

Vaxcel W0079 is a light fixture that can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including anchors, screws, and wire nuts. The fixture has a glass shade that can be easily removed for cleaning. The fixture is rated for use with a maximum of 50 watts, and it comes with a G9 bulb. The fixture is also dimmable, so you can adjust the light output to your desired level.

Here are some of the features and possible use cases of the Vaxcel W0079:

  • Easy to install: The fixture comes with all the necessary hardware for installation, and the instructions are easy to follow.

Vaxcel W0079 is a light fixture that can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including anchors, screws, and wire nuts. The fixture has a glass shade that can be easily removed for cleaning. The fixture is rated for use with a maximum of 50 watts, and it comes with a G9 bulb. The fixture is also dimmable, so you can adjust the light output to your desired level.

Here are some of the features and possible use cases of the Vaxcel W0079:

  • Easy to install: The fixture comes with all the necessary hardware for installation, and the instructions are easy to follow.
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
W0079
Glass bracket (E)
Bulb G9 Max.50W (H)
(Included)
Back Plate
Parts:
140410
Parts Number (5060MM)
Mounting Screw (C)
Wire Nut (A)
Glass Bracket (E)
Glass Shade (F)
Anchor (D)
Dry Wall Screw (B)
Rubber Pad
Parts Number (5060HD)
Glass Shade (F)
Parts Number (9599EW)
Anti-Knocking Glass (G)
Parts Number (9599AK)
Bulb (H)
Parts Number (8065HL)
Anti-Knocking
Glass (G)
Metal Pad
Lock Nut
Fixture
Mounting
Screw
Set Screw
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d’alimentation principale au panneau
central de disjoncteurs avant d’installer le luminaire.
1. Unscrew four fixture mounting screws, and remove the mounting plate from the back plate.
2. Place the glass shade onto the glass bracket as shown.
3. Attach the glass bracket to the back plate by aligning set screws on glass bracket with holes on the
back plate. Slide set screws through holes, secure them with two metal pads and lock nuts.
4. Install a bulb (Included). See relamping label at socket area or packaging for maximum allowed
wattage.
5. Mount the rubber pad, thread the anti-knocking glass onto the socket.
Fig.1
140410
6. Attach the mounting plate to the wall.
a) If the wall material is wood:
Attach the mounting plate to the outlet box by using two mounting screws, then secure the dry
wall screws through the set holes to the wall.
b) If the wall material is cement:
Place the mounting plate to the outlet box by using two mounting screws, and then mark the
target on the wall from the set hole for drilling two holes. Unscrew two mounting screws and
remove the mounting plate. Drill holes and thread the anchors into the holes, then attach the
mounting plate to the outlet box by using two mounting screws. Secure the dry wall screws
through the set holes into the anchors.
7. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections
by using the wire nuts:
---Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
---Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power
source.
---Attach the fixture grounding wire to the mounting plate with the green grounding screw. Then
connect it to the house grounding wire with a wire nut.
Carefully put the wires back into the outlet box.
8. Attach the back plate to the mounting plate by aligning holes, secure the fixture mounting screws
from the side hole of the back plate onto the side of the mounting plate.
9. Turn on the power at the main fuse or circuit breaker box.
Note: The lamp is hot. Do not touch the bulb with fingers. It's extremely important to keep the
bulb clean. Any dust or sweat may damage the bulb immediantely. If accidently touched or dirty,
clean with fabric carefully.
Mounting Screw (C)
Mounting Plate
House Grounding Wire
Green Grounding Screw (C)
Fixture Grounding Wire
Wire Nut (A)
Outlet Box
Anchor (D)
Dry Wall Screw (B)
Set Hole
Fig. 2
Fixture Mounting Screw
A: 8"
B: 10"
C: 5"
A
B
C
  • Page 1 1
  • Page 2 2

Vaxcel W0079 Operating instructions

Brand
Vaxcel
Model
W0079
Category
Wall & ceiling mounts accessories
Type
Operating instructions

Vaxcel W0079 is a light fixture that can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including anchors, screws, and wire nuts. The fixture has a glass shade that can be easily removed for cleaning. The fixture is rated for use with a maximum of 50 watts, and it comes with a G9 bulb. The fixture is also dimmable, so you can adjust the light output to your desired level.

Here are some of the features and possible use cases of the Vaxcel W0079:

  • Easy to install: The fixture comes with all the necessary hardware for installation, and the instructions are easy to follow.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents