Xerox C226 Installation guide

WorkCentre C226

Quick Connect Guide

Purpose:

Refer to this guide to modify the printer network settings at the printer user

interface screens if required. For complete instructions refer to the Customer

documentation for additional information.

Note:

A Network Administrator is required to ensure that the printer is configured

properly. To properly configure the printer, the Network Administrator must

supply a valid IP Address, a Subnet Mask, and a Gateway Address if applicable.

DHCP is enabled by default. For more information in regards to Novell printing

and configuration, please refer to the Customer documentation.

Procedure:

The WorkCentre C226 has been designed to connect to a TCP/IP network with

minimal changes. Connect the printer to the network and review the Network

Settings List. Continue with Steps 2-6 and make changes to the printer port /

network as required for your network infrastructure.

Step 1: Default Printer Settings

Default Port Settings

Parallel Port – Enabled

Netware – Enabled

Port 9100 – Enabled

FTP – Enabled

Internet Service – Enabled

Default

Network Settings

IP Address DHCP (ON)

Printer Name: XC010228

Workgroup: Workgroup

Step 2: IP Setup

Follow this procedure if you want to make any changes to the port settings. If no

changes are required then please move on to Step 3.

1. Press Machine Administration button on the Local User Interface Operation Panel.

2. Press System Administrator Tools button. Enter Password (Default: 00000).

3. Press Printer Selections.

4. Press Network Settings.

5. Press IP Address Settings.

6. DHCP is default – uncheck DHCP and enter IP information if applicable.

7. Press OK.

8. Press Yes to restart after making changes.

9. Reboot the printer using on/off switch on the left side of machine.

10. If no further changes are required, continue to Step 4 in this guide.

Step 3: Protocol Enablement

Follow this procedure if you want to make any changes to the port settings. If no

changes are required then please move on to Step 4.

1. Press Machine Administration button on the Local User Interface Operation Panel.

2. Press System Administrator Tools button. Enter Password (Default: 00000).

3. Press Printer Selections.

4. Press Network Settings.

5. Press Enable protocols by toggling them on/off as checkboxes

6. Press OK.

7. Press Yes to restart after making changes.

8. Reboot the printer using on/off switch on the left side of machine.

9. If no further changes are required, continue to Step 5 in this guide.

Step 4: Print Lists

1. Press the Machine Administration button on the Local User Interface Operation Panel.

2. Press Print Lists and Test Pages.

3. Press Print Test Pages.

4. Press one of the following:

a. Printer Settings List

b. PCL Font List

c. PCL Symbol Set List

d. Network Interface Card Page.

5. Press the CA button on the Local UI Operation Panel to return to the

Main Screen.

Machine Administration

Resolution: 600 DPI

Language:

English British

Hardware Specs

Base Memory: 128 MB

Optional Memory: 512 MB

Total Memory: 640 MB

HDD:

40 GB

FW. Version

PCU Ver: x.xx

ICU Ver: x.xx

Boot Ver: x.xx

PRT:

xxx

Installed Device

2-Sided System: 2-Sided Module

Paper Feeding Options: 2 Tray Unit

High Cap. Feeder: Installed

Paper Exit Options: Saddle Stitch Fin.

Print Server Card: Installed

Default Settings

Copies: 1 Set

Orientation: Portrait

Default Paper: Size: A4

Default Paper Type: Plain

Default Output Tray: Centre Tray

PCL Symbol Set: Roman-1

Font Number:1 Font: Courier

PCL5c Emulation

Font Source: Resident

Pitch Size: 10.00

Point Size:

12.00

Network Information

Enable DHCP: Yes/No

IP Address: xxx.xxx.xxx

IP Sub. Mask: xxx.xxx.xxx

IP Gateway: xxx.xxx.xxx

Enable TCPIP: Yes

Enable Netware: Yes

Enable NetBEUI: Yes

NIC Firmware Version: x.x.x

NW Print Server Name: XCxxxxxxx

NetBEUI Workgroup: Workgroup

NetBEUI Printer Name: XCxxxxxxx

Color Calibration

Low Method: AutoCalibration

Date & Time: 4/03/2005 6:45

Tray Settings

Tray 1: A4 /Plain

Tray 2: A3 /Plain

Tray 3 A4 /Plain

Tray 5 A4 /Plain

Tray 6 /A4 Plain

Print/Copy/Fax: Enabled

A

uto Tra

y

Switchin

g

: On

Total Count

Color: 930

B/W:

1294

X

erox WorkCentre C22

6

Custom Setting List

Sample Printer Settings List

Step 5: Web User Interface Instructions

A PC client connected to the network is required to complete the printer network setup.

Follow this procedure if you want to make any other changes to the printer configuration.

1. Open a Web Browser (Internet Explorer).

2. Verify Proxy Servers are being bypassed for local web addresses.

3. Type the TCP/IP address assigned to the printer into the URL window. (Refer to the

Network Interface Card Page for the TCP/IP address.)

4. Make necessary changes by selecting one of the options on the let side pane in the

window.

5. To save changes or edit the default login information is:

a. Username: “admin”

b. Password: “Xerox”

6. Save changes and reboot the printer.

7. Print out a new Network Interface Card Page to review new settings.

8. (Please refer to Step 4 for additional information.)

Sample WorkCentre C226 Web Page

Step 6: Load Windows Print Drivers

1. Run Setup.exe

2. Select Language

3. License Agreement will appear, select Yes

4. Read the Welcome Screen and click “Next”

5. Select Print Driver button followed by Next when window appears

6. Select “Standard” or “Custom Installation” (Default: Standard)

7. Select printer to be installed

8. Select if you wish to have Windows Programs use this as default printer then Next

9. Enter Printer Name to used, click Next

10. Install Display Font window appears, make selection then click Next

11. Select Next, driver will be installed along with printer

12. Printer is now installed, select OK then Close again and restart if prompted

Note:

This install procedure is for all Windows Clients supported for the WorkCentre

C226. Please refer to the documentation for installing printers using the “Add Printer

Wizard”. For USB & Parallel port instructions please refer to the documentation.

Print Driver Installation for Netware

Please refer to the System Administration Guide which came packaged with your new

machine for complete instructions on loading drivers for Netware.

Print Driver Installation for Mac OS using Ethertalk

Printer Type: LaserWriter 8

Printer Name: Xerox WorkCentre C226

PPD Installation & Configuration

Mac OS 8.6-9.x

1. Insert the PS3 Expansion Kit CD Rom into machine

2. Double-click the CDROM

3. Double-click the Mac OS Folder

4. Double Click the Installer icon

5. Click Install button

6. Software License Agreement appears, Click “Yes”

7. Click Continue

8. PPD is now installed

Setup Printer 8.6-9.x

1. Select Chooser from the Apple Menu

2. Select the LaserWriter 8 Icon

3. Select the AppleTalk zone for your network.

4. Select the XC010228 printer and click Create

5. Once installed, Select Configure and set the options for your printer.

Mac OS X

1. Insert the PS3 Expansion Kit CD Rom into machine

2. Double-click the CDROM

3. Double-click the Mac OS Folder

4. Double-click the OS version

5. Double Click the Installer icon and then Continue

6. Software License Agreement appears, Click Yes

7. Choose Hard Disk Location and select Continue

8. Click Install button

9. When message appear “The software was successfully installed”, select Close – Your

PPD has been installed.

Setup Printer for OS X

1. Select Applications from the Go Menu

2. Double-click the Utilities Folder

3. Double-click the Print Center Icon

4. Click Add, select AppleTalk followed by your AppleTalk zone name

5. Select the name of your AppleTalk device for the WorkCentre C226

6. PPD window will appear, select Xerox followed by the PPD

7. Click the Add button

8. Click the printer name in the Printer List window and select Show Info from the

Printers Menu.

9. Select Installable Options

10. Set the options for your printer

11. Close the window, your printer is now configured.

Page is loading ...

English Trademark information

• Microsoft Windows operating system is a registered trademark

or trademark of the Microsoft Corporation in the U.S.A. and

other countries.

• Windows 98, Windows Me, Windows NT 4.0, Windows 2000,

and Windows XP are registered trademarks or trademarks of

Microsoft Corporation in the U.S.A. and other countries.

• Netscape Navigator is a trademark of Netscape

Communications Corporation.

• Adobe

®

Reader Copyright

©

1987-2005 Adobe Systems

• Adobe, the Adobe logo, Acrobat, and the Acrobat logo are

trademarks of Adobe Systems Incorporated.

All other company names and product names appearing in this

manual are the trademarks of their respective owners.

Español Información de marcas comerciales

• El sistema operativo Microsoft Windows es una marca

registrada o marca comercial de Microsoft Corporation en

EE.UU. y en otros países.

• Windows 98, Windows Me, Windows NT 4.0, Windows 2000 y

Windows XP son marcas registradas o marcas comerciales de

Microsoft Corporation en EE.UU. y otros países.

• Netscape Navigator es una marca comercial de Netscape

Communications Corporation.

• Adobe

®

Reservados todos los derechos.

• Adobe, el logotipo de Adobe, Acrobat y el logotipo de Acrobat

son marcas comerciales de Adobe Systems Incorporated.

Todos los otros nombres de compañías y nombres de productos que

aparecen en este manual son marcas comerciales de sus

respectivos propietarios.

Page is loading ...

Xerox C226 Installation guide

Related papers

Other documents