Indesit WIXL 105 (KW) (V) User guide

Brand: Indesit

Model: WIXL 105 (KW) (V)

Category: Washing machines

Type: User guide

Contents

Installation, 2-3-4-5

Unpacking and levelling, 2

Electric and water connections, 2-3-4

The first wash cycle, 4

Technical details, 5

Washing machine description, 6-7

Control panel, 6

Leds, 7

Starting and Programmes, 8

Briefly: how to start a programme, 8

Programme table, 8

Personalisations, 9

Setting the temperature, 9

Setting the spin speed, 9

Functions, 9

Detergents and laundry, 10

Detergent dispenser, 10

Bleach cycle, 10

Preparing your laundry, 10

Special items, 10

Precautions and advice, 11

General safety, 11

Disposal, 11

Saving energy and respecting the environment, 11

Care and maintenance, 12

Cutting off the water or electricity supply, 12

Cleaning your appliance, 12

Cleaning the detergent dispenser, 12

Caring for your appliance door and drum, 12

Cleaning the pump, 12

Checking the water inlet hose, 12

Troubleshooting, 13

Service, 14

Before calling for Assistance, 14

WASHING MACHINE

WIXL 105

Instructions for use

GB AR

English,1

, 29

Français, 15

Installation

 Keep this instruction manual in a safe place for future

reference. Should the appliance be sold, transferred or

moved, make sure the instruction manual

accompanies the washing machine to inform the new

owner as to its operation and features.

 Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do not

install it and contact your retailer.

3. Remove the four

protective screws and

the rubber washer with

the respective spacer,

situated on the rear of

the appliance (see

figure).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another

location.

 Packaging materials are not children's toys.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or other.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured

according to the

worktop, must not

exceed 2°.

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose and

screw the latter onto a

cold water tap with a 3/4

gas threaded mouth (see

figure).

Before making the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance

(see figure).

3. Make sure there are no kinks or bends in the hose.

 The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

 If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

alternatively, place it over

the edge of a basin, sink

or tub, fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

65 - 100 cm

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of

the plug. Replacements can be obtained directly from

your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured

Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible to

the plug body and dispose of it as described above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to

leave it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by an

authorised serviceman.

Warning!

The company denies all liability if and when these

norms are not respected.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

The first wash cycle

Once the appliance has been installed, and before you

use it for the first time, run a wash cycle with

detergent and no laundry, setting the 90°C programme

without a pre-wash cycle.

Technical details

Model

WIXL 105

Dimensions

59.5 cm wide

85 cm high

53.5 cm deep

Capacity

from 1 to 6 kg

Electric

connections

voltage 230/240 Volts 50 Hz maximum

absorbed power 2050 W

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rpm

Control

programmes

according to

IEC456 directive

programme 2; temperature 60°C;

run with a load of 6 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96 CE

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Washing machine description

Control panel

FUNCTION

Buttons

Detergent dispenser

ON-OFF

Button

START/RESET

Button

TEMPERATURE

Knob

PROGRAMME

Knob

Leds

SPIN SPEED

Knob

ON-OFF/

DOOR

LOCK

Led

Detergent dispenser: to add detergent and fabric

softener (see page 10).

LEDS: to find out which wash cycle phase is under

way.

If the Delay Timer function has been set, the time

left until the programme starts will be indicated (see

page 7).

SPIN SPEED knob: to set the spin speed or exclude

the spin cycle completely (see page 9).

FUNCTION buttons: to select the functions

available. The button corresponding to the function

selected will remain on.

TEMPERATURE knob: to set the temperature or the

cold wash cycle (see page 9).

START/RESET button: to start the programmes or

cancel any incorrect settings.

ON-OFF/DOOR LOCK Led: to find out whether the

washing machine is on and if the appliance door can

be opened (see page 7).

ON/OFF button: to turn the washing machine on

and off.

PROGRAMME knob: to select the wash

programmes. The knob stays still during the cycle.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

ON-OFF/DOOR LOCK led:

If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any

damages, wait for the LED to flash before you open the appliance door.

 The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED

indicates there is an abnormality (see page 13, Troubleshooting).

Leds

The LEDS provide important information.

This is what they can tell you:

Delay set:

If the Delay Timer function has been enabled (see

page. 9), once you have started the programme, the

LED corresponding to the delay set will begin to flash:

As time passes, the remaining delay will be

displayed, and the corresponding LED will flash:

Once the set delay is complete, the flashing LED will

turn off and the programme set will start.

Cycle phase under way:

During the wash cycle, the LEDs gradually illuminate

on to indicate the cycle phase under way:

Prewash

Wash

Rinse

Spin cycle

Note: during draining, the LED corresponding to

the Spin cycle phase will be turned on.

Function buttons

The FUNCTION BUTTONS also act like LEDS.

When a function is selected, the corresponding

button is illuminated.

If the function selected is incompatible with the

programme set, the button will flash and the

function will not be enabled.

If you set a function that is incompatible with another

function you selected previously, only the last one

selected will be enabled.

Type of fabric and

degree of soil

Program-

mes

Tem pe-

rature

Detergent

Fabric

softener

Stain removal

option/bleach

Cycle

len gth

(minutes)

Description of wash cycle

pre-

wash

Standard

Cotton:

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C   

155

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Extremely soiled whites

(sheets, tablecloths, etc.)

90°C  

Delicate/

Traditional

150

Wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Heavily soiled whites and

fast colours

60°C  

Delicate/

Traditional

140

Wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Heavily soiled whites and

delicate colours

40°C  

Delicate/

Traditional

125

Wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Sligh tly s oiled w hites

and delicate colours (shirts,

jump ers, etc.)

40°C  

Delicate/

Traditional

Wash cycle, rinse cycles,

intermediate and final spin cycles

Synthetics:

Heavily soiled fast

colours (baby linen, etc.)

60°C   Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Synthetics:

Heavily soiled fast

colours (baby linen, etc.)

40°C   Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Synthetics:

Delicate colours (all

types of slightly soiled garments )

40°C   Delicate

Wash cycle, rinse cycles, anti-

crease or delicate spin cycle

Wool

40°C  

Wash cycle, rinse cycles, anti-

crease and delicate spin cycle

Very delicate fabrics (curtains,

silk, viscose, etc.)

30°C  

Wash cycle, rinse cycles, anti-

crease or draining cycle

Time 4 you

Cotton:

Heavily soiled whites and

fast colours

60°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Cotton:

Sligh tly s oiled w hites

and delicate colours (shirts,

jump ers, etc.)

40°C  

Wash cycle, rinse cycles,

intermediate and final spin cycles

Synthetics:

Delicate colours (all

types of slightly soiled garments )

°C



Wash cycle, rinse cycles,

delicate spin cycle

Synthetics:

Delicate colours (all

types of slightly soiled garments )

30°C   30

Wash cycle, rinse cycles and

delicate spin cycle

Sports

Sports shoes

(MAX. 2 pairs)

°C

 50

Cold wash (without detergents),

wash cycle, rinse cycles, and

delicate spin cycle

Fabrics for sportswear (Tracksuits,

shorts, etc.)

30°C   60

Wash cycle, rinse cycles,

intermediate and final spin cycles

PARTIAL PROGRAMMES

Rinse 

Delicate/

Traditional

Rinse cycles and spin cycle

Spin cycle Draining and spin cycle

Drain Draining

Starting and Programmes

Programme table

Briefly: starting a programme

1. Switch the washing machine on by pressing button .

All the LEDS will light up for a few seconds and

the ON-OFF/DOOR LOCK Led will begin to flash.

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the PROGRAMME knob to the programme

required.

4. Set the wash temperature (see page 9).

5. Set the spin speed (see page 9).

6. Add the detergent and any fabric softener

(see page 10).

7. Start he programme by pressing the START/RESET

button.

To cancel it, keep the START/RESET button pressed

for at least 2 seconds.

8. When the programme is finished, the ON-OFF/

DOOR LOCK Led will flash to indicate that the

appliance door can be opened. Take out your

laundry and leave the appliance door ajar to allow

the drum to dry thoroughly. Turn the washing

machine off by pressing button

Notes

-For programmes 8 and 9, we advise against exceeding a wash load of 3.5 kg.

-For programme 13 we advise against exceeding a wash load of 2 kg.

-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.

Special programme

Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts

30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash

different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Personalisations

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 8).

The temperature can be lowered, or even set to a cold wash (

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the programme selected.

The maximum spin speeds for each programme are as follows:

Programmes Maximum spin speed

Cotton 1000 rpm

Synthetics 800 rpm

Wool 600 rpm

Silk no

The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol

The washing machine will automatically prevent you from selecting a spin speed higher than the maximum

speed for each programme.

To avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by

continuously rotating the drum at a speed which is slightly faster than the normal washing speed.

When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than

the set frequency.

If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.

The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;

2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the

programme set.

Function Effect Comments

Enabled with

programmes:

Delay Timer

Delays the start

of the wash by

up to 9 hours.

Press the button repeatedly until the LED corresponding to the

desired delay is turned on.

The fifth time the button is pressed, the function will be disabled.

N.B.: Once you have pressed the Start/Reset button, the delay

can only be decreased if you wish to modify it.

All

Stain removal

Bleaching cycle

designed to

remove the

toughest stains.

Please remember to pour the bleach into extra compartment 4

(se

e page 10)

This function is incompatible with the EASY IRON function.

2, 3, 4, 5,

Rinse cycle.

Easy iron

This option

reduces the

amount of

creasing on

fabrics, making

them easier to

iron.

When this function is set, programmes 4, 5, 6, 7 will end with the

laundry left to soak (Anti-crease) and the Rinse cycle phase

LED will flash.

- to conclude the cycle, press the START/RESET button;

- to run the draining cycle alone, set the knob to the relative

symbol and press the START/RESET button.

This function is incompatible with the STAIN REMOVAL function.

3, 4, 5, 6, 7,

8, 9, 10,

Rinse cycle.

Extra Rinse

Increases the

efficiency of the

rinse.

Recommended when the appliance has a full load or with large

quantities of detergent.

1, 2, 3, 4, 5,

8, 9, 10, 12,

13, Rinse

cycle.

Detergent dispenser

Good washing results also depend on the correct

dose of detergent: adding too much detergent won't

necessarily make for a more efficient wash, and may

in fact cause build up on the interior of your

appliance and even pollute the environment.

Open up the detergent

dispenser and pour in

the detergent and fabric

softener, as follows.

compartment 1: Detergent for pre-wash

(powder)

Before pouring in the detergent, make sure that

extra compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in

immediately prior to the wash cycle start.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

extra compartment 4: Bleach

 Do not use hand wash detergent because it may

form too much foam.

Bleach cycle

 Traditional bleach should be used on sturdy

white fabrics, and delicate bleach for coloured

fabrics, synthetics and for wool.

Place extra compartment

4, provided, into

compartment 1.

When pouring in the

bleach, be careful not to

exceed the "max" level

indicated on the central

pivot (see figure).

To run the bleach cycle alone, pour the bleach into

extra compartment 4 and set the Rinse programme

. To bleach during a wash cycle, pour in the

detergent and fabric softener, set the desired

programme and enable the Stain removal option

(see page 9).

The use of extra compartment 4 excludes the

possibility of using the pre-wash cycle. In addition, the

bleach cycle cannot be run with programmes 7 (Silk)

and Daily (see page 8).

Preparing your laundry

 Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

 Empty all pockets and check for loose buttons.

 Do not exceed the weight limits stated below,

which refer to the weight when dry:

Sturdy fabrics: max 6 kg

Synthetic fabrics: max 2.5 kg

Delicate fabrics: max 2 kg

Wool: max 1,5 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow

case or mesh bag. Wash them separately without

exceeding half the appliance load. Use programme 7

which excludes the spin cycle automatically.

Quilted coats and windbreakers: if they are

padded with goose or duck down, they can be

machine-washed. Turn the garments inside out and

load a maximum of 2-3 kg, repeating the rinse cycle

once or twice and using the delicate spin cycle.

Wool: for best results, use a specific detergent, taking

care not to exceed a load of 1,5 kg.

Detergents and laundry

Precautions and advice

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

 The washing machine was designed and built in

compliance with the applicable international safety

regulations. The following information is provided for

your safety and should consequently be read carefully.

General safety

 This appliance has been designed for non-

professional, household use and its functions must

not be changed.

 This washing machine should only be used by

adults and in accordance with the instructions

provided in this manual.

 Never touch the washing machine when barefoot

or with wet or damp hands or feet.

 Do not pull on the power supply cable to unplug

the appliance from the electricity socket. Pull the

plug out yourself.

 Do not open the detergent dispenser while the

appliance is in operation.

 Do not touch the drain water as it could reach

very high temperatures.

 Never force the washing machine door: this could

damage the safety lock mechanism designed to

prevent any accidental openings.

 In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

 Always keep children well away from the

appliance while in operation.

 The appliance door tends to get quite hot during

the wash cycle.

 Should it have to be moved, proceed with the

help of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading your laundry into the washing

machine, make sure the drum is empty.

Disposal

 Disposing of the packaging material: observe local

regulations, so the packaging can be re-used.

 Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest technology,

your washing machine only needs less than half the

amount of water to get the best results: an objective

reached to respect the environment.

Saving on detergent, water,

energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. A full load instead

of two half loads allows you to save up to 50% on

energy.

 The pre-wash cycle is only necessary on

extremely soiled garments. Avoiding it will save on

detergent, time, water and between 5 and 15%

energy.

 Treating stains with a stain remover or leaving

them to soak before washing will cut down the

need to wash them at high temperatures. A

programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

 Use the correct quantity of detergent depending

on the water hardness, how soiled the garments

are and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric

softener as much as possible.

 If you use your washing machine from late in the

afternoon until the early hours of the morning, you

will help reduce the electricity board's peak load.

The Delay Timer option (see page 9) helps to

organise your wash cycles accordingly.

 If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Care and maintenance

Cutting off the water or electricity

supply

 Turn off the water tap after every wash. This will

limit the wear of your appliance's water system

and also prevent leaks.

 Unplug your appliance when cleaning it and

during all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can

be cleaned with a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

Remove the dispenser

by pulling it out (see

figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for your appliance door and

drum

 Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump that does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber that protects the

pump, situated in the lower part of the same.

 Make sure the wash cycle has ended and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front of the

washing machine (see

figure);

2. unscrew the lid

rotating it anti-

clockwise (see figure): a

little water may trickle

out. This is perfectly

normal;

3. clean the interior thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the water inlet hose at least once a year. If

you see any cracks, replace it immediately: during

the wash cycles, water pressure is very strong and

a cracked hose could easily split open.

 Never use hoses that have already been used.

Troubleshooting

ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description

Your washing machine could fail to work. Before calling for Assistance (see page 14), make sure the problem can't

easily be solved by consulting the following list.

Problem

The washing machine won't

start.

The wash cycle won't start.

The washing machine fails to

load water.

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

The ON-OFF/DOOR LOCK Led

flashes rapidly at the same

time as at least one other LED.

There is too much foam.

Possible causes/Solution:

 The appliance is not plugged into the socket, or not enough to

make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 The

button has not been pressed.

 The START/RESET button has not been pressed.

 The water tap is not turned on.

 A delayed start has been set (using the Delay Timer, see page 9).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap is not turned on.

 There is a water shortage.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The drain hose is not fitted between 65 and 100 cm from the floor

(see page 3).

 The free end of the hose is underwater (see page 3).

 The wall drainage system doesn't have a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and call for Assistance. If the dwelling is on one of

the upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

 The programme does not foresee the draining: some programmes

require enabling the draining manually (see page 8).

 The Easy iron option is enabled: to complete the programme, press

the START/RESET button (see page 9).

 The drain hose is bent (see page 3).

 The drain duct is clogged.

 The drum was not unblocked correctly during installation (see page 2).

 The washing machine is not level (see page 2).

 The washing machine is closed in between furniture cabinets and

the wall (see page 2).

 The water inlet hose is not screwed on correctly (see page 2).

 The detergent dispenser is obstructed (to clean it, see page 12).

 The drain hose is not secured properly (see page 3).

 Switch off the machine and unplug the appliance;

wait for approximately 1 minute then switch it on again.

If the problem persists, contact Assistance.

 The detergent is not suitable for machine washing (it should bear

the definition "for washing machines" or "hand and machine wash",

or the like).

 You used too much detergent.

Before calling for Assistance:

 Check whether you can solve the problem on your own (see page 13);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Service Centre on the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised servicemen.

 If the machine has been installed or used incorrectly, you may be charged for the maintenance callout

service.

Notify the operator of:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Service

Français

Sommaire

Installation, 16-17-18-19

Déballage et mise à niveau, 16

Raccordements hydrauliques et électriques, 17-18

Premier cycle de lavage, 18

Caractéristiques techniques, 19

Description du lave-linge, 20-21

Bandeau de commandes, 20

Voyants, 21

Mise en marche et Programmes, 22

En bref: démarrage d'un programme, 22

Tableau des programmes, 22

Personnalisations, 23

Sélection de la température, 23

Sélection de l'essorage, 23

Fonctions, 23

Produits lessiviels et linge, 24

Tiroir à produits lessiviels, 24

Cycle blanchissage, 24

Triage du linge, 24

Pièces de linge particulières, 24

Précautions et conseils, 25

Sécurité générale, 25

Mise au rebut, 25

Economies et respect de l'environnement, 25

Entretien et soin, 26

Coupure de l'arrivée d'eau et de courant, 26

Nettoyage du lave-linge, 26

Nettoyage du tiroir à produits lessiviels, 26

Entretien du hublot et du tambour, 26

Nettoyage de la pompe, 26

Contrôle du tuyau d'arrivée de l'eau, 26

Anomalies et remèdes, 27

Assistance, 28

Consultation à tout moment, 28

LAVE-LINGE

WIXL 105

Mode d'emploi

 Conservez ce mode d'emploi pour pouvoir le

consulter à tout moment. En cas de vente, de cession

ou de déménagement, veillez à ce qu'il suive toujours

le lave-linge pour que son nouveau propriétaire soit

informé sur son mode de fonctionnement et puisse

profiter des conseils correspondants.

 Lisez attentivement les instructions: elles fournissent

d'importantes informations sur l'installation, l'utilisation

et la sécurité.

Déballage et mise à niveau

Déballage

1. Déballez le lave-linge.

2. Contrôlez que le lave-linge n'a pas été endommagé

pendant le transport. S'il est abîmé, ne le raccordez

pas et contactez votre revendeur.

3. Enlevez les quatre vis

de protection pour le

transport, le

caoutchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Bouchez les trous à l'aide des bouchons plastique

fournis.

5. Bouchez à l'aide du bouchon fourni les trois trous

où était logée la prise, situés sur la partie arrière, en

bas à droite.

6. Conservez bien toutes ces pièces: il faudra les

remonter en cas de transport du lave-linge.

 Les emballages ne sont pas des jouets pour enfants.

Mise à niveau

1. Installez le lave-linge sur un sol plat et rigide, sans

l'appuyer contre des murs, des meubles ou autre.

2. Si le sol n'est pas

parfaitement horizontal,

vissez ou dévissez les

petits pieds avant (voir

figure) pour niveler

l'appareil; son angle

d'inclinaison, mesuré

sur le plan de travail, ne

doit pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité de la

machine et évite qu'il y ait des vibrations, du bruit et

des déplacements en cours de fonctionnement. Si la

machine est posée sur de la moquette ou un tapis,

réglez les petits pieds de manière à ce qu'il y ait

suffisamment d'espace pour assurer une bonne

ventilation.

Raccordements hydrauliques et

électriques

Raccordement du tuyau d'arrivée de l'eau

1. Montez le joint A sur

l'extrémité du tuyau

d'alimentation et vissez-le

à un robinet d'eau froide

à embout fileté 3/4 gaz

(voir figure).

Faites couler l'eau

jusqu'à ce qu'elle soit

limpide et sans

impuretés avant de

raccorder.

2. Raccordez le tuyau

d'alimentation au lave-

linge en le vissant à la

prise d'eau prévue, dans

la partie arrière en haut

à droite (voir figure).

3. Faites attention à ce que le tuyau ne soit ni plié ni

écrasé.

 La pression de l'eau doit être comprise entre les

valeurs indiquées dans le tableau des Caractéristiques

techniques (voir page ci-contre).

 Si la longueur du tuyau d'alimentation ne suffit pas,

adressez-vous à un magasin spécialisé ou à un

technicien agréé.

Installation

Raccordement du tuyau de vidange

Raccordez le tuyau

d'évacuation, sans le

plier, à un conduit

d'évacuation ou à une

évacuation murale placés

à une distance du sol

comprise entre 65 et 100

cm;

ou bien accrochez-le à

un évier ou à une

baignoire, dans ce cas,

fixez le support en

plastique fourni avec

l'appareil au robinet (voir

figure). L'extrémité libre

du tuyau d'évacuation

ne doit pas être plongée

dans l'eau.

 L'utilisation de tuyaux de rallonge est absolument

déconseillée, si vous ne pouvez vraiment pas faire

autrement vous devrez utiliser un tuyau de même

diamètre et de longueur maximum de 150 cm.

Branchement électrique

Avant de brancher votre électroménager à la prise de

courant, contrôlez que:

 la prise est bien avec terre et conforme aux

réglementations applicables en la matière;

 la prise électrique est bien apte à supporter la

puissance maximum de l'électroménager figurant

sur la plaquette des caractéristiques (voir page 19);

 la tension d'alimentation est bien comprise entre

les valeurs figurant sur la plaquette des

caractéristiques (voir page 19);

 la prise est bien compatible avec la fiche du lave-

linge. Autrement, remplacez la prise ou la fiche.

Votre électroménager dispose à présent d'une fiche

moulée 13 ampères qui peut être branchée dans une

prise compatible pour utilisation immédiate. Veuillez

lire les instructions suivantes avant d'utiliser votre

électroménager.

65 - 100 cm

ATTENTION - L'ELECTROMENAGER DOIT ETRE

RACCORDE A LA MASSE. LES OPERATIONS

DECRITES CI-APRES DOIVENT ETRE EFFECTUEES

PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible:

En cas de remplacement d'un fusible défectueux, utilisez

toujours des fusibles de 13 ampères ASTA conformes au

standard BS1362 et remontez le couvercle du fusible. Si

vous avez perdu le couvercle du fusible, n'utilisez pas la

fiche tant que la pièce manquante n'aura pas été

remplacée.

Couvercles des fusibles:

Si vous remplacez le couvercle du fusible, veillez à ce que

sa couleur soit bien celle qui est indiquée par le code ou

l'indication colorée à la base de la fiche. Pour toute pièce

détachée, adressez-vous directement au centre

d'assistance technique le plus proche de chez vous.

Démontage de la fiche:

Si l'électroménager est équipé d'une fiche incorporée

qui ne peut pas être câblée à nouveau et s'il faut faire

passer le câble à travers des divisions, des unités,

etc. contrôlez que:

la fiche est bien remplacée par une autre câblable à

nouveau de 13 ampères portant la marque BSI

ou bien:

que le câble est bien raccordé directement à la prise

de 13 ampères, contrôlée par un interrupteur (confor-

me BS 5733) accessible sans qu'il faille déplacer

l'électroménager.

Elimination de la fiche:

Avant d'éliminer la fiche, rendez les broches

inutilisables de manière à ce que la fiche ne puisse

pas être branchée accidentellement dans une prise.

Instructions pour le raccordement du câble à une fiche

alternative:

Important: les couleurs des fils du câble de réseau

correspondent à la codification suivante:

Jaune/Vert Terre

Bleu Neutre

Marron Alimenté

Les couleurs des fils du câble pourraient ne pas

correspondre aux indications de couleur qui identifient

les broches de la fiche, procédez comme suit:

raccordez le fil jaune/vert à la borne repérée par la

lettre E ou

ou de couleur verte ou jaune/vert

raccordez le fil marron à la borne repérée par la lettre

L ou de couleur rouge

raccordez le fil bleu à la borne repérée par la lettre N

ou de couleur noire.

AssistanceAnomaliesPrécautions EntretienProgrammesInstallation Description

Bac produits

En cas d'utilisation d'une fiche de 13 ampères (BS

1363), installez un fusible de 13 ampères dans la fiche

ou sur l'adaptateur ou sur la carte de distribution.

En cas de doute sur l'alimentation électrique de votre

électroménager, faites appel à un électricien qualifié

avant de le mettre en service.

Raccordement d'une fiche alternative:

les couleurs des fils du câble de réseau correspondent

à la codification suivante:

BLEU NEUTRE (N)

MARRON ALIMENTE (L)

JAUNE/VERT TERRE (E)

Elimination de l'électroménager:

Lors de la mise au rebus de l'électroménager,

débarrassez-le de sa fiche en coupant le câble

d'alimentation le plus près possible de cette dernière

et éliminez comme décrit précédemment.

 Votre lave-linge ne doit pas être installé dehors,

même à l'abri, car il est très dangereux de le laisser

exposé à la pluie et aux orages.

 Après installation du lave-linge, la prise de courant

doit être facilement accessible.

 N'utilisez ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni écrasé.

 Le câble d'alimentation ne doit être remplacé que

par des techniciens agréés.

Attention!

Nous déclinons toute responsabilité en cas de non

respect des normes énumérées ci-dessus.

Premier cycle de lavage

Avant la première utilisation de la machine, effectuez

un cycle de lavage avec un produit lessiviel mais sans

linge et sélectionnez le programme à 90°C sans

prélavage.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Caractéristiques techniques

Modèle

WIXL 105

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 53,5 cm

Capacité

de 1 à 6 kg

Raccordements

électriques

tension 230/240 Volt 50 Hz

puissance maximale absorbée 2050 W

Raccordements

hydrauliques

pression maximale 1 MPa (10 bar)

pression minimale 0,05 MPa (0,5 bar)

capacité du tambour 52 litres

Vitesse

d'essorage

jusqu'à 1000 tours minute

Programmes de

contrôle selon la

norme IEC456

programme 2; température 60°C;

effectué avec une charge de 6 kg.

Cet appareil est conforme aux

Directives Communautaires suivantes:

- 73/23/CEE du 19/02/73 (Basse

Tension) et modifications suivantes

- 89/336/CEE du 03/05/89

(Compatibilité électromagnétique) et

modifications suivantes

- 2002/CE 96

AssistanceAnomaliesPrécautions EntretienProgrammesInstallation Description

Bac produits

Bandeau de commandes

Description du lave-linge

Tiroir à produits lessiviels

Touche

MISE EN MARCHE/

ARRET

Touche

START/RESET

Bouton

TEMPÉRATURE

Bouton

PROGRAMMES

Voyants

Touches

FONCTION

Bouton

ESSORAGE

Voyant

ALLUMAGE/

HUBLOT

VERROUILLE

Tiroir à produits lessiviels: chargement des

produits lessiviels et additifs (voir page 24).

Voyants: suivi du stade d'avancement du

programme de lavage.

Si la fonction Départ différé a été sélectionnée,

indiquent le temps résiduel avant le démarrage du

programme (voir page 21).

Bouton ESSORAGE: sélection de l'essorage ou

exclusion (voir page 23).

Touches FONCTION: sélection des fonctions

disponibles. La touche correspondant à la fonction

sélectionnée restera allumée.

Bouton TEMPÉRATURE: sélection de la

température ou lavage à froid (voir page 23).

Touche START/RESET: démarrage des

programmes ou annulation (en cas d'erreur).

Voyant ALLUMAGE/HUBLOT VERROUILLE: pour

comprendre si le lave-linge est branché et si le

hublot peut être ouvert (voir page 21).

Touche MISE EN MARCHE/ARRET: mise en

marche ou arrêt du lave-linge.

Bouton PROGRAMMES: choix des programmes

(voir page 22).

En cours de lavage, le bouton ne bouge pas.

Page is loading ...

Indesit WIXL 105 (KW) (V) User guide

Brand: Indesit

Model: WIXL 105 (KW) (V)

Category: Washing machines

Type: User guide

Download PDF

report

in other languages

français: Indesit WIXL 105 (KW) (V) Mode d'emploi

Indesit WIXL 105 (KW) (V) User guide

Indesit WIXL 105 (KW) (V) User guide

in other languages

Related papers

Other documents