Best Best EB15 Installation guide

Brand: Best

Model: Best EB15

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

KEX808736SS

ENGLISH.......................................2

FRANÇAIS...................................13

ESPAÑOL....................................24

For use with Best By Broan Exterior Blower model

EB6, EB9, EB12, or EB15.

Model KEX8087

In USA - BEST Hartford, Wisconsin

In CANADA - BEST Drummondville, QC, Canada

For additional Information visit www.BestRangeHoods.com

- 2 -

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock service

panel to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accor-

dance with all applicable codes and standards, including fire-rated construction codes

and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue

(chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equip-

ment manufacturer’s guidelines and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any separate solid-state speed control device.

8. To reduce the risk of fire, use only steel ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers

hat may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambe’).

C. Clean ventil

ating fans frequently. Grease should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will

result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already know how to operate

it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

INTENDED FOR DOMESTIC COOKING ONLY

- 3 -

CAUTION

1. For indoor use only.

2. To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent

exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. Take care when using cleaning agents or detergents.

4. Avoid using food products that produce flames under the Range Hood.

5. For general ventilating use only. Do not use to exhaust hazardous or explosive materi-

als and vapors.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall

spray, construction dust, etc. off power unit.

7. Your hood motor has a thermal overload which will automatically shut off the motor if it

becomes overheated. The motor will restart when it cools down. If the motor continues

to shut off and restart, have the hood serviced.

8. For best capture of cooking impurities, the bottom of the hood should be a minimum of

24" and a maximum of 30" above the cooking surface. See page 9 for mounting restric-

tions.

9. Two installers are recommended because of the large size and weight of this hood.

10. This product is equipped with a thermostat which may start blower automatically. To

reduce the risk of injury and to prevent power from being switched on accidentally,

switch power off at service panel and lock or tag service panel.

11. Use with approved cord-connection kit only.

12. Please read specification label on product for further information and requirements.

For use with Best By Broan Exterior Blower model

EB6, EB9, EB12, or EB15.

- 4 -

OPERATION

Controls

Your hood is operated using the (5) push buttons located at eye-level, on the front

edge of the hood. It includes an on-off light switch, a filter cleaning alarm, ten-minute

run delay and blower speed settings.

Light Button, Filter Alarm, Alarm Reset:

• Turns halogen lights on and off. Press once to turn the lights ON to low level.

Press a second time to turn the lights on to a brighter level. Press a third time

to turn the light off.

• When blower is off, this switch remains lit after 30 hours of operation, indicating

a need to replace the charcoal filter.

• After filters are cleaned or replaced, press this button for one-second to reset

the filter alarm.

Blower On-Off, Speed 1

• Press once to turn the blower ON to its lowest running speed.

• Quickly pressing the switch once delays blower shut off by ten-minutes.

• Depress and hold switch down to turn blower off without delay.

Blower Speed 2

• With blower running, press switch 2 to change blower speed to medium-low.

• Quickly pressing the switch once delays blower shut off by ten-minutes.

• To turn off without delay, depress and hold down the 0-1 switch.

Blower Speed 3

• With blower running, press switch 3 to change blower speed to medium-high.

• Quickly pressing the switch once delays blower shut off by ten-minutes.

• To turn off without delay, depress and hold down the 0-1 switch.

Blower Speed 4

• With blower running, press switch 4 to change blower speed to high.

• Quickly pressing the switch once delays blower shut off by ten-minutes.

• To turn off without delay, depress and hold down the 0-1 switch.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a

device that will turn on or speed up the blower if it senses excessive heat above

the cooking surface.

1) If blower is OFF, it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting, it turns blower up to HIGH speed.

When the temperature level drops to normal, the blower will return to its original

setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned

OFF. When this occurs, it is impossible to turn the blower OFF with its switch.

If you must stop the blower, do it from the main electrical panel.

0 - 1 2 3 4

Light switch /

Filter Alarm &

Reset

Blower On-

Off / Speed

Blower

Speed 2

Blower

Speed 3

Blower

Speed 4

- 5 -

FUSE REPLACEMENT

IF LIGHTS FAIL TO OPERATE, DISCONNECT

THE POWER AT THE SERVICE ENTRANCE.

CHECK THE FUSE AND REPLACE IF

NECESSARY.

1. Remove the filters.

2. Locate the control board box and

transformer, positioned up inside the hood.

Fig. 2

3. Unfasten (4) screws from the control board

box and remove the cover. Fig. 2

4. Remove the fuse from the control board.

Fig. 2

5. Replace the fuse with the same size and

amperage (5x20mm, 4amp, 125volt).

6. Replace the control box cover and secure

with (4) screws.

7. Reconnect power at the service

entrance.

FIG. 2

FUSE

DECORATIVE

FLUE

CONTROL

BOARD BOX

HALOGEN BULBS

This range hood requires two halogen bulbs

(Type JC, 12Volt, 20Watt Max, G-4 Base).

ALWAYS SWITCH OFF THE ELECTRICAL

SUPPLY BEFORE CARRYING OUT ANY

OPERATIONS ON THE APPLIANCE.

To change bulbs:

1. Open the cover by prying from the proper

slots. - DO NOT ROTATE. CAUTION: BULB

MAY BE HOT! Fig. 1

2. Replace with a Type JC, 12Volt, 20Watt

Max, G-4 Base bulb. Do not touch

replacement bulb with bare hands!

FIG. 1

- 6 -

MAINTENANCE

Proper maintenance of the Range Hood will

assure proper performance of the unit.

Grease Filter

Grease filter should be cleaned when the light

switch flashes or remains lit when the blower

is off (i.e. 30 hours of operation). Use a warm

detergent solution to clean filters. Filters are

dishwasher safe. See page 12 for filter removal

and installation instructions.

Hood Cleaning

Stainless steel is one of the easiest materials to keep clean. Occasional care will

help preserve its fine appearance.

Cleaning tips:

•

Hot water with soap or detergent is all that is usually needed.

•

Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to

avoid water marks.

•

For discolorations or deposits that persist, use a non-scratching household

cleanser or stainless steel polishing powder with a little water and a soft cloth.

•

For stubborn cases, use a plastic scouring pad or soft bristle brush together with

cleanser and water. Rub lightly in direction of polishing lines or "grain" of the

stainless finish. Avoid using too much pressure which may mark the surface.

•

DO NOT allow deposits to remain for long periods of time.

•

DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere

to the surface causing rust.

•

DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to

remain in contact with stainless steel for extended periods. Many of these com-

pounds contain chemicals which may be harmful. Rinse with water after expo-

sure and wipe dry with a clean cloth.

Painted surfaces should be cleaned with warm water and mild detergent only.

GREASE

FILTER

- 7 -

PREPARE THE HOOD

Unpack hood and check contents.

You should receive:

1 - Hood

1 - Decorative Flue Assembly

1 - Discharge Collar

1 - Parts Bag (B080810482) containing:

1 - Mounting Bracket

1 - Flue Mounting Bracket

8 - Mounting Screws (4.8 x 38mm Pan Head)

4 - Mounting Screws (3.9 x 9.5mm Pan Head)

2 - Bracket Screws (3.9 x 5.7mm Flat Head)

8 - Drywall Anchors

1 - Installation Instructions

1 - Warranty Card

MOUNTING

BRACKET

DISCHARGE

COLLAR

FLUE MOUNTING

BRACKET

8 MOUNTING SCREWS

(4.8 x 38mm Pan Head)

8 DRYWALL

ANCHORS

4 MOUNTING

SCREWS (3.9 x 9.5mm

Pan Head)

DECORATIVE

FLUE

2 BRACKET SCREWS

(3.9 x 5.7mm Flat Head)

- 8 -

INSTALL THE DUCTWORK

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the exterior blower will be mounted. See illustra-

tions below for mounting location suggestions and restrictions.

2. A straight, short duct run will allow the hood to perform most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the

hood. Use as few of them as possible. Larger ducting may be required for best

performance with long duct runs.

4. After the exterior blower has been installed, connect round metal ductwork and

work back towards the hood location. Use duct tape to seal joints between

ductwork sections.

5. An 8” round to 10” round transition (Model 414) is required. For best air

performance, install the adapter as close to the range hood as possible.

EXTERIOR

BLOWER

10” ROUND

DUCT

HOOD

DECORATIVE

FLUE

EXTERIOR

BLOWER

8” TO 10”

ROUND

ADAPTER

8” ROUND

ELBOW

10”

ROUND

DUCT

8” ROUND

DUCT

CAUTION: MAY NOT

FIT UNDER EAVES

OF SINGLE STORY

HOMES

SUGGESTED MOUNTING LOCATIONS

24” TO 30” ABOVE

COOKING SURFACE

(See “INSTALL

MOUNTING BRACKET”

SECTION, page 9, for

mounting restrictions)

EXTERIOR BLOWER SELECTION

CAUTION: To reduce the risk of fire and electric shock, install this rangehood only

with EB6, EB9, EB12 or EB15 Exterior Blowers.

The exterior ventilator must be UL listed for Canadian and U.S. use, and evaluated

for use with solid state speed control, rated 120V, 60 Hz, 6.0 A max.

- 9 -

INSTALL MOUNTING

BRACKET

1. Construct wood wall framing that is flush

with interior surface of wall studs.

Make sure:

a) the framing is centered over

installation location.

b) the height of the framing will allow the

mounting bracket to be secured to the

framing within the dimensions shown.

After wall surface is finished, secure mount-

ing bracket to framing using dimensions

shown.

Note: minimum hood distance above cook top must not be less than 24”. A maximum

of 30” above cook top is highly recommended for best capture of cooking impurities.

Distances over 30” are at the installer and users discretion; and if ceiling height and

flue length permit.

FRAMING BEHIND CROSS SUPPORT

DRYWALL

CEILING

HEIGHT

8 FEET

9 FEET

HOOD DISTANCE ABOVE 36” HIGH COOK TOP (SEE NOTE BELOW)

24”

25” 26” 27” 28” 29” 30”

MOUNTING BRACKET LOCATION ABOVE 36” HIGH COOK TOP

36-3/4”

37-3/4” 38-3/4” 39-3/4” 40-3/4” 41-3/4”

10 FEET WITH

FEXTK8087

37-3/4” 38-3/4” 39-3/4” 40-3/4” 41-3/4” 42-3/4”

36-3/4”

37-3/4” 38-3/4” 39-3/4” 40-3/4” 41-3/4” 42-3/4”

INSTALL FLUE MOUNTING

BRACKET

1. Assemble the flue mounting bracket,

adjusting outside width as shown. Fig.4

2. Carefully center the mounting bracket

directly over the range hood location.

3. Secure the bracket assembly to the ceiling

using (2) 4.8x38mm mounting screws

and drywall anchors. Make sure the

bracket is pushed into the corner, tight

against the wall and centered over the

hood.

FLUE MOUNTING

BRACKET

9 3/4”

FIG. 4

3.9x5.7mm FLAT

HEAD BRACKET

SCREWS

WOOD CROSS SUPPORT

BEHIND DRYWALL

- 10 -

PREPARE THE HOOD

Note: On stainless steel hoods, carefully

remove the plastic protective film from all

exterior surfaces of the hood and decorative

flues, prior to final installation.

1. Locate (2) tabs on top of the hood and inside

the round discharge opening. Fig. 5

2. Fold both tabs up 90 degrees. Fig. 5

3. Install the discharge collar inside the tabs

and secure with (2) 3.9 x 9.5mm screws.

Fig. 5

4. Attach an adequate length of 8” round steel

ducting to the range hood’s discharge collar.

Fig. 5

5. Duct tape all joints to make them secure

and air tight.

DISCHARGE

COLLAR

TABS

8” DUCT

FIG. 5

MOUNTING

SCREWS

(4.8x38)

RECTANGULAR

CUTOUT

MOUNTING

BRACKET

FIG.6

INSTALL THE HOOD

1. Install the hood into its mounted position.

2. Align the rectangular opening on the back

of the hood with the wall-mounting bracket.

Gently lower the hood until it securely

engages the bracket. Fig. 6

3. Level the hood and secure with (4) mounting

screws (4.8x38mm). Use drywall anchors

provided if wall studs or framing are not

available. Fig. 6

- 11 -

WIRING

CAUTION: All electrical wiring should be

done by a qualified person (s) in accordance

with all applicable codes and standards.

This range hood must be properly grounded.

Do not turn power on at service panel until

all wires have been connected.

Blower connection at hood:

1. Run 2-wire plus ground power cable from

the exterior blower to the hood’s wiring box

marked “motor connection”. Fig. 7

2. Remove the cover from the wiring box and

remove one knockout. Fig. 7

3. Feed 6” of cable through the knockout

opening and secure the cable to the wiring

box with an appropriate connector. Fig.7

4. Make electrical connections at the hood.

Connect white-to-white, red-to-black and

green-to-ground. Fig.7

5. Replace the wiring box cover and screws.

make sure wires are not pinched between

the cover and box.

Exterior blower connection:

1. Make electrical connections at the exterior

blower (see instructions provided with the

exterior blower).

Power connection at hood:

1. Run 120 VAC electrical power cable to the

hood wiring box marked “120VAC input”.

Fig. 8

2. Remove the cover from the wiring box and

remove one knockout. Fig. 8

3. Feed 6” of cable through the knockout

opening and secure the cable to the wiring

box with an appropriate connector. Fig. 8

4. Make electrical connections at the hood.

Connect white-to-white, black-to-black

and green-to-ground. Fig. 8

5. Replace the wiring box cover and screws.

Make sure wires are not pinched between

the cover and box.

BOX MARKED “120

VAC INPUT”

BLOWER CONNECTION AT HOOD

BOX MARKED

“MOTOR

CONNECTION”

Exterior blower

FIG. 7

FIG. 8

CONNECT:

WHITE-TO-WHITE,

RED-TO-BLACK,

GREEN-TO-GROUND.

POWER CONNECTION AT HOOD

CONNECT:

WHITE-TO-WHITE,

BLACK-TO-BLACK,

GREEN-TO-GROUND.

120 Volt 60Hz

LINE-IN

- 12 -

INSTALL THE FLUE

1. Carefully slide the upper flue down inside

the lower flue. Fig. 9

2. Lift and position the flue assembly into

the recessed area of the hood. Make sure

it is properly seated. Fig. 9

3. Raise the upper flue until its holes align

with holes in the flue mounting bracket

(located on ceiling). Fig. 9

4. Secure the flue with (2) mounting screws

(3.9x9.5mm). Fig. 9

3.9x9.5mm

MOUNTING SCREWS

FIG. 9

GREASE

FILTERS

FIG. 10

INSTALL FILTER(S)

1. To remove the GREASE filter(s), grip the

latch tab and pull it down. This will disen-

gage the filter from the hood. Tilt the filter

downward and remove. Fig. 10

2. To install the GREASE filter(s), align rear

filter tabs with slots in the hood. Pull latch

tab down, push filter into position and

release. Make sure the filter is securely

engaged after assembly.

WARRANTY

ONE YEAR LIMITED WARRANTY FOR BEST PRODUCTS

Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be

free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR

MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is

found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDES-

CENT BULBS, FUSE, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This

warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse,

negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary

to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states do

not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE

PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE

LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH

PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty

supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number stated

below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At

the time of requesting warranty service, you must present evidence of the original purchase date.

In USA - Best®, 926 W. State Street, Hartford, WI 53027 (800-558-1711)

In Canada - Best®, 550 Lemire Blvd., Drummondville, QC J2C 7W9 (866-737-7770)

www.BestRangeHoods.com

Page is loading ...

- 35 -

SERVICE PARTS

MODEL KEX8087 HS - Parts for stainless steel models shown. For service parts

for black, white, polished brass, or brushed copper models, call Broan Customer

Service.

KEY NO. PART NO. DESCRIPTION

7 BE3345107 Support

9 B08087169 Grease Filter

16 BE3345329 Electrical Box Support

19 B03295005 Terminal Box

26 B02300891 Halogen Lamp Bulb

37 B02300787 Heat Sentry

38 B03292357 Control Board Box

39 B03294033 Control Board Cover

57 BE3300527 Damper Flap

62 B08091602 Blower Mounting Cover

86 B08088242 Discharge collar + Damper Flap

115 BE3334250 Wiring Box

116 BE3334252 Wiring Box Cover

118 B003100591 Decorative Flue Bottom

119 BE3346837 Decorative FlueTop

120 B08091367 Flue Mounting Bracket

144 B03292287 Wire Clamp

166 B08086644 Control Board

208 B02300739 Transformer

223 B03293068 Switch Button

228 B08086249 Controls Board

230 B03293069 Switch Board Box Cover

234 B03293009 Control Board Box

235 BE3345106 Switch Mounting Bracket

332 BE3345328 Cover

474 B02300798 Halogen Lamp Housing

477 B03294776 Terminal Cover

* B06107786 Switch Assembly (Includes Key Nos. 223, 228,

230, 234, 235)

998 B080810482 Hardware Package

* Not shown assembled.

Page is loading ...

Best Best EB15 Installation guide

Brand: Best

Model: Best EB15

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

KEX808736SS

Download PDF

report

in other languages

français: Best Best EB15 Guide d'installation
español: Best Best EB15 Guía de instalación

Best Best EB15 Installation guide

This manual is also suitable for

Best Best EB15 Installation guide

in other languages

Related papers

Other documents