Binks 2001SS User manual

Brand: Binks

Model: 2001SS

Category: Power fine-spray systems

Type: User manual

This manual is also suitable for

2001
2001V

Binks Model

2001, 2001V AND 2001SS

SPRAY GUNS

Replaces

Part Sheet

77-2316R-13

Part

Sheet

77-2316R-14

1. Air Nozzle Assembly

2. Gun Body

3. Side Port Control

4. Fluid Control Knob

5. Air Connection 1/4" NPS (m)

6. Fluid Connection 3/8" NPS (m)

PRESSURE FEED TANK

HOOKUP

For portable painting operations

(double regulator).

Air pressure for atomization and fluid

supply is regulated by two individual

air regulators on tank (see figure 4).

PRESSURE FEED CIRCULATING

HOOKUP

For heavy production spraying.

Air pressure atomization regulated at

extractor. Fluid pressure regulated at

fluid regulator (see figure 5).

Your new Binks spray gun is exceptionally

rugged in construction, and is built to stand

up under hard, continuous use. However, like

any other fine precision instrument, its most

efficient operation depends on a knowledge

of its construction, operation, and mainte-

nance. Properly handled and cared for, it will

produce beautiful, uniform finishing results

long after other spray guns have worn out.

TYPES OF INSTALLATION

SIPHON FEED CUP HOOKUP

Air pressure for atomization is regulated at

extractor. The amount of fluid is adjusted by

fluid control screw on gun, viscosity of paint,

and air pressure (see figure 1).

PRESSURE FEED CUP HOOKUP

For fine finishing with limited spraying.

Air pressure for atomization is regulated at

extractor; fluid pressure at cup regulator. For

heavy fluids and internal mix nozzle spray-

ing, fluid adjusted by control screw on gun.

Pressure cup also available less regulator

(see figure 2).

PRESSURE FEED TANK HOOKUP

For medium production spraying (sin-

gleregulator).

Air pressure for atomization is regulated at

extractor, fluid pressure at tank regulator

(see figure 3).

Extractor

Figure 1

Air

Siphon Cup

Extractor

Figure 5

Air

Fluid

Regulator

Fluid

Figure 4

Air

Supply

Air Supply

Extractor

Air

Inlet

Figure 3

Air

Fluid

Outlet

Pressure

Tank

Pressure

Tank

Fluid

Oil & Water

Extractor

Cup

Regulator

Figure 2

Air

Fluid

Pressure Cup

WARNING

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows:

CAUTION

Hazards or unsafe practices which could

result in minor personal injury, product

or property damage.

WARNING

Hazards or unsafe practices which could

result in severe personal injury, death or

substantial property damage.

NOTE

Important installation, operation or

maintenance information.

Read the following warnings before using this equipment.

FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT,

SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).

READ THE MANUAL

Before operating finishing equipment, read and

understand all safety, operation and maintenance

information provided in the operation manual.

AUTOMATIC EQUIPMENT

Automatic equipment may start suddenly without

warning.

INSPECT THE EQUIPMENT DAILY

Inspect the equipment for worn or broken parts

on a daily basis. Do not operate the equipment

if you are uncertain about its condition.

NEVER MODIFY THE EQUIPMENT

Do not modify the equipment unless the

manufacturer provides written approval.

KNOW WHERE AND HOW TO SHUT OFF THE

EQUIPMENT IN CASE OF AN EMERGENCY

PRESSURE RELIEF PROCEDURE

Always follow the pressure relief procedure in the

equipment instruction manual.

NOISE HAZARD

You may be injured by loud noise. Hearing

protection may be required when using this

equipment.

STATIC CHARGE

Fluid may develop a static charge that must be

dissipated through proper grounding of the

equipment, objects to be sprayed and all other

electrically conductive objects in the dispensing

area. Improper grounding or sparks can cause a

hazardous condition and result in fire, explosion

or electric shock and other serious injury.

FIRE AND EXPLOSION HAZARD

Never use 1,1,1-trichloroethane, methylene

chloride, other halogenated hydrocarbon solvents

or fluids containing such solvents in equipment

with aluminum wetted parts. Such use could

result in a serious chemical reaction, with the

possibility of explosion. Consult your fluid

suppliers to ensure that the fluids being used are

compatible with aluminum parts.

WEAR SAFETY GLASSES

Failure to wear safety glasses with side shields

could result in serious eye injury or blindness.

DE-ENERGIZE, DISCONNECT AND LOCK OUT ALL

POWER SOURCES DURING MAINTENANCE

Failure to De-energize, disconnect and lock out

all power supplies before performing equipment

maintenance could cause serious injury or death.

OPERATOR TRAINING

All personnel must be trained before operating

finishing equipment.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to

rupture, malfunction, or start unexpectedly and

result in serious injury.

KEEP EQUIPMENT GUARDS IN PLACE

Do not operate the equipment if the safety

devices have been removed.

PROJECTILE HAZARD

You may be injured by venting liquids or gases

that are released under pressure, or flying debris.

PINCH POINT HAZARD

Moving parts can crush and cut. Pinch points are

basically any areas where there are moving parts.

The first requirement for a good resultant finish is

the proper handling of the gun. The gun should be

held perpendicular to the surface being covered and

moved parallel with it. The stroke should be started

before the trigger is pulled and the trigger should

be released before the stroke is ended. This gives

accurate control of the gun and material.

The distance between gun and surface should be 6

to 12 inches depending on material and atomizing

pressure. The material deposited should always be

even and wet. Lap each stroke over the preceding

stroke to obtain a uniform finish.

NOTE

To reduce overspray and obtain maximum efficiency, always

spray with the lowest possible atomizing air pressure.

Coating should be even

and wet when spraying

Coating will

be light at

this point

Coating will

be heavy

at this point

Start

stroke

Pull

trigger

Release

trigger

End of

stroke

RIGHT

WRONG

TRAVEL OF GUN

6 to 12 inches

AIR PRESSURE

GUN HANDLING

BINKS OIL AND WATER EXTRACTOR IS IMPORTANT

5/16”

1/4”

Only 34 PSI at gun inlet

25 feet of 1/4” I.D. hose causes a drop of

26 PSI between the air supply and the gun.

(NOT RECOMMENDED)

48 PSI at gun inlet

25 feet of 5/16” I.D. hose causes a drop of

12 PSI between the air supply and the gun.

For this reason Binks recommends the use

of 5/16” hose.

(RECOMMENDED)

With 60 psi applied at air supply

Atomizing pressure must be set properly to allow for the drop

in air pressure between the regulator and the spray gun.

Achieving a fine spray finish without the use of a

good oil and water extractor is virtually impossible.

A Binks regulator / extractor serves a double pur-

pose. It eliminates blistering and spotting by keep-

ing air free of oil and water, and it gives precise air

pressure control at the gun.

Binks recommends using Model HFRL-508 Oil and

Water Extractor / Regulator. See your local distributor

for other models.

Cross section view

showing comparison of inside

hose diameters (actual size).

60 lbs. regulated pressure

It is extremely poor practice to mount the oil and

water extractor on or even near the compressor unit.

The temperature of the air is greatly increased as it

passes through the compressor and this compressed

air must be cooled before the moisture in it will con-

dense. If the air from the compressor is still warm

when it passes through the oil and water extractor,

moisture will not be effectively removed, but will

remain in suspension. Then, when the air cools in

the hose beyond the extractor, the moisture will

condense into drops of water and cause trouble.

Air lines must be properly drained

Pitch all air lines back towards the compressor so

that condensed moisture will flow back into the air

receiver where it can be removed by opening a

drain. Every low point on an air line acts as a water

trap. Such points should be fitted with an easily

accessible drain. See diagram.

AIR SUPPLY

In normal operation, the wings on

the nozzle are horizontal as illus-

trated here. This provides

a vertical fan shaped pattern which

gives maxi-

mum coverage

as the gun is

moved back

and forth par-

allel to the

surface being

finished.

Spray width adjustment: Turn clock-

wise for round, counterclockwise for fan.

Fluid control screw: Turn clockwise to

decrease flow, counterclockwise to

increase flow.

As width of spray is increased, more

material must be allowed to pass through

the gun to obtain the same coverage on

the increased area.

SIPHON SPRAYING

Set atomization pressure at approximate-

ly 50 PSI for lacquer and 60 PSI for

enamel. Test spray. If the spray is too

fine, reduce the air pressure or open fluid

control screw. If the spray is too coarse,

close the fluid control screw. Adjust the

pattern width and repeat adjustment of

spray if necessary.

PRESSURE SPRAYING

After selecting correct size fluid orifice,

set fluid pressure for desired flow. Open

atomization air and test spray. If spray is

too fine, reduce air pressure. If spray is

too coarse, raise air pressure. Adjust pat-

tern width and repeat adjustment of spray.

Keeping fluid control screw in open posi-

tion will reduce fluid needle wear.

The spray pattern of

the Binks gun is variable

from round to flat with

all patterns in between.

Spray width

adjustment

Fluid

control

screw

FAULTY PATTERNS AND HOW TO CORRECT THEM

PATTERN CAUSE CORRECTION

Dried material around the

outside of the fluid nozzle tip

at position “C” restricts the

passage of atomizing air at

one point through the center

opening of air nozzle and

results in pattern shown.

This pattern can also be caused

by a loose air nozzle.

Dried material in side-port

“A” restricts passage of air.

Greater flow of air from

cleaner side-port “B” forces

fan pattern in direction of

clogged side.

Dissolve material in side-ports with thinner,

then blow gun clean. Do not poke into

openings with metal instruments.

Remove air nozzle and wipe off fluid tip

using rag wet with thinner. Tighten air

nozzle.

A split spray or one that is heavy on each

end of a fan pattern and weak in the mid-

dle is usually caused by:

(1) Too high an atomization air pressure

(2) Attempting to get too wide a spray pat-

tern with thin material.

Reducing air pressure will correct cause (1).

To correct cause (2), open material control

to full position by turning to left. At the

same time, turn spray width adjustment to

right. This will reduce width of spray, but

will correct split spray pattern.

(1) Dried out packing around material nee-

dle valve permits air to get into fluid

passageway. This results in spitting.

(2) Dirt between fluid nozzle seat and

body or loosely installed fluid nozzle

will make gun spit.

(3) A loose or defective swivel nut on

siphon cup or material hose can cause

spitting.

To correct cause (1) back

up knurled nut (E), place

two drops of machine oil

on packing, replace nut

and tighten with fingers

only. In aggravated cases,

replace packing.

To correct cause (2), remove fluid nozzle (F),

clean back of nozzle and nozzle seat in gun

body using rag wet with thinner, replace

nozzle and draw up tightly against body.

To correct cause (3), tighten or replace

swivel nut.

When used with a cup, thinner or suitable

solvent should be siphoned through gun

by inserting tube in open container of

that liquid. Move trigger constantly to

thoroughly flush passageway and to clean

tip of needle.

CLEANING GUN USED WITH

PRESSURE TANK

Shut off the air supply to the tank and

release the pressure on the tank. Open

vent and loosen air nozzle. Hold a piece

of cloth, wadded in the hand over the air

nozzle and pull the trigger, the air will

back up through the fluid nozzle, and

force the fluid out of the hose into the

tank. Next put enough thinner into the

tank to wash the hose and gun thorough-

ly and spray this through the gun until it

is clean. Then blow out the fluid hose to

dry it and remove all traces of materials

by attaching it to the air line.

THINNER

Keep thinner level below packing.

It is extremely poor practice to place an

entire gun in thinner. When this is done,

the solvent dissolves the oil in the

leather packing and causes the gun to

spit. It is good practice to place the noz-

zle and fluid connection in thinner.

Vessel used should be shallow enough to

prevent thinner from reaching packing.

LUBRICATION

Daily oil fluid needle packing, air valve

packing, and trigger bearing screw.

Occasionally coat needle valve spring

with petroleum jelly. OIL ALL WORK-

ING PARTS EVERY DAY.

CONTROLLING THE FAN SPRAY: The

fan spray for an external mix nozzle set-

up is easily controlled by means of the

side port control (28). Turning this con-

trol to the right, or clockwise, until it is

closed will give a round spray; turning it

to the left, or counter-clockwise, will

widen the spray into a fan shape of any

width desired. The direction of the fan

spray, either horizontal or vertical, is

obtained by turning the air nozzle to the

desired position, then tightening the

retainer ring.

CONTROLLING THE FLUID

If a fluid pressure tank is used, the

amount of fluid can be controlled by reg-

ulating the pressure on the tank. The

amount of fluid can also be controlled

by means of the fluid control screw (42).

Turning this screw to the right, or clock-

wise, reduces the amount of fluid; to the

left, or counter-clockwise, increases the

amount of fluid.

FAULTY SPRAY

A faulty spray is caused by improper

cleaning or dried material around the

fluid nozzle tip or in the air nozzle. Soak

these parts in a solvent that will soften

the dried material and remove with a

brush or cloth.

If either the air nozzle or fluid nozzle is

damaged, the part must be replaced

before a perfect spray can be obtained.

TO REPLACE THE FLUID PACKING:

Remove the fluid control screw (42),

spring (39) and needle. Then remove the

fluid packing nut (12) and take out the

old packings with a small stiff wire.

Replace with new packings (11) oiled

lightly and assemble in reverse order. To

set packing, insert needle, tighten nut

until the needle begins to be too stiff for

the spring to move the needle. Then

loosen nut 1/2 to 3/4 turn.

CORRECTING AIR LEAK

THROUGH GUN

Air leaking through the gun is caused by

the valve stem assembly (6), not seating

properly against the valve body (8).

Remove the valve body (8) and valve

stem assembly (6). Thoroughly clean

parts and inspect for damage. Replace

worn or damaged parts and assemble in

reverse order.

CORRECTING AIR LEAK AROUND

AIR VALVE STEM

Air leaking around the air valve stem (6)

may be caused by worn packings (9) or

damaged air valve stem (6). Remove

trigger (3), packing nut (10) and pack-

ings (9). Clean extended portion of air

valve stem (6) and inspect for damage; if

stem is damaged, replace same as above,

insert new packings and assemble in

reverse order.

Binks MODELS 2001, 2001V AND 2001SS SPRAY GUNS – POINTERS ON CLEANING

Keep thinner

level below

packing

Thinner

➧

CAUTION

Never use metal instruments to clean

the air or fluid nozzles. These parts

are carefully machined and any dam-

age to them will cause a faulty spray.

Binks MODELS 2001, 2001V AND 2001SS SPRAY GUNS – GENERAL MAINTENANCE

SPRAY GUN

1. Immerse only the front end of the

gun until solvent just covers the fluid

connection.

2. Use a bristle brush and solvent to

wash off accumulated paint.

3. Do not submerge the entire spray gun

in solvent because:

a. the lubricant in the leather pack-

ings will dissolve and the pack-

ings will dry out.

b. the lubricant at wear surfaces will

dissolve causing harder operation

and faster wear.

c. residue from dirty solvent may

clog the narrow air passages in

the gun.

4. Wipe down the outside of the gun

with solvent-dampened rag.

5. Lubricate gun daily. Use a light

machine oil on:

a. fluid needle packing.

b. air valve packing.

c. side port control packing.

d. trigger pivot point.

Coat the fluid control spring with

vaseline.

AIR NOZZLE, FLUID NOZZLE,

FLUID NEEDLE

1. All nozzles and needles are precision

made. They should be handled with

care.

2. Do not make any alterations in the

gun. To do so could cause finishing

difficulties.

3. To clean nozzles, soak them in sol-

vent to dissolve any dried material,

then blow them clean with air.

4. Do not probe any of the holes in the

nozzles with metal instruments. If

probing is necessary, use only a tool

that is softer than brass.

CAUTION

Never use lubricants contaning sili-

cone. This material may cause finish

defects.

A. Material to Be Sprayed

Select the type of fluid you want to

spray or a fluid which has the same

characteristics as one of those listed.

B. Method of Feeding Material to

the Gun

Fluid Nozzle—Consider the speed of

application and the viscosity of the

fluid to be sprayed. Referring to the

Fluid Nozzle Orifice Size Chart,

those fluid nozzles which can be

changed within an air nozzle are

indicated.

Air Nozzle—Choice is determined by

the type of fluid to be sprayed and the

volume of air available for the gun.

—External Mix Nozzles, which are

generally used, accomplish atomiza-

tion outside the nozzle. Spray pat-

terns are adjustable from round to fan

with all intermediate patterns.

(Designated by the letter “E”).

Siphon Type External Mix Nozzles,

designated by the letter “S”, will

siphon the material from a cup. Used

generally for refinishing and touch-up

work which does not require large

quantities of paint.

Pressure Type External Mix Nozzles,

designated by the letter “P”, require

pressure to feed the material to the

nozzle. A pressure cup, pressure tank

or pump is necessary. Used for pro-

duction work and where large quanti-

ties of fluid are handled. This type of

nozzle has a greater range of fluid

flow and does not limit the size of

the paint container.

—Internal Mix Nozzles mix the air

and fluid within the air nozzle. The

spray pattern is determined by the

shape of the nozzle and cannot be

changed. Internal mix nozzles require

less air and produce slightly less fog.

Pressure equipment must be used

with this type of nozzle.

Recommended for maintenance

spraying of heavy materials where a

fine finish is not required.

(Designated by the letter “I”).

C. Volume of Air (CFM required)

The cubic feet per minute (CFM)

listed at 30, 50 and 70 PSI is the

actual air used by the air nozzle.

Increase of pressure subsequently

increases volume of air required by

air nozzle, or vice versa. Assume that

a compressor will produce 3-5 CFM

per horsepower.

NOZZLE SELECTION

(See chart on page 7)

NOTE

All parts on a spray gun should be

screwed in hand tight at first; this will

avoid the possibility of cross threading

the parts. If the parts can not be

turned by hand easily, make sure you

have the correct parts, unscrew,

realign, and try again. NEVER use

undue force in mating parts.

NOTE

The greater the air consumption, the

faster the fluid may be applied or the

finer a given amount of fluid can be

atomized.

VERY THIN 63SS 63P PE 4.5 7.5 10.0 5.0 563

14–16 Sec.— No. 2 Zahn 63ASS 63P PE 5.1 8.7 12.2 11.0 563A

Wash Primers, Dyes, Stains, 63BSS 63PB PE 9.0 14.3 20.0 14.0 563A

Solvents, Water, Inks 66SS 66S SE 3.4 5.0 9.0 565

66SS 66SD SE 7.9 12.1 10.5 565

66SS 66SK SE 11.0 15.2 19.5 13.0 565

63BSS 200 PI 3.1 5.2 6.4 12.0 563A

THIN 63ASS 63P PE 5.1 8.7 12.2 11.0 563A

16–20 Secs.—No. 2 Zahn 66SS 66SK SE 11.0 15.2 19.5 13.0 565

Sealers, Primers, 63BSS 200 PI 3.1 5.2 6.4 12.0 563A

Lacquers, Inks, Lubricants 63CSS PI 3.9 5.5 7.4 9.0 563A

Zinc Chromates, Acrylics

MEDIUM 63BSS 63PB PE 9.0 14.3 20.0 14.0 563A

19–30 Secs.—No. 2 Zahn 63CSS 63PR PE 9.5 15.5 19.5 18.0 563A

Lacquers, Syn. Enamels 66SS 66SD SE 7.9 12.0 11.0 565

Varnishes, Shellacs, Fillers, 66SS 66SK SE 11.0 15.2 19.5 13.0 565

Primers, Epoxies, Urethanes 63CSS 200 PI 3.1 5.2 6.4 12.0 563A

Lubricants, Wax Emulsions 66SS PI 3.9 5.5 7.4 9.0 565

HIGH SOLIDS

Enamels 65SS 63PR PE 9.5 15.5 19.5 18.0 565

HEAVY (CREAM-LIKE)

Over 28 Secs.—No. 4 Ford 67SS 67PB PE 9.5 14.9 19.5 12.0 567

House Paint, Wall Paint (Oil, Latex), 68SS 68PB PE 9.5 14.1 19.1 12.0 568

Block Sealers, Mill Whites, 67SS 206 PI 6.0 9.5 13.0 15.0 567

Vinyls, Acrylics, Epoxies, Gel Coats 68SS 201 PI 4.6 6.8 9.1 11.0 568

VERY HEAVY 68SS 68PB PE 9.5 14.1 19.1 12.0 568

Unaggregated, Block Fillers, 68SS 206 PI 6.2 9.8 13.2 15.0 568

Textured Coatings, Fire Retardants, 59ASS 242 PI 4.1 6.0 8.2 6.0 559

Road Marking Paint, Bitumastics, 59ASS 244 PI 7.8 11.5 15.2 12.0 559

Cellular Plastisols, Underbody, 59BSS 250 PI 7.3 11.0 14.7 RD 559

Roof Coatings 59BSS 252 PI 7.8 11.5 15.2 6.0 559

59CSS 262 PI 7.3 11.0 14.7 6.0 559

ADHESIVES 63CSS 63PB PE 9.0 14.3 20.0 14.0 563A

Waterbase 66SS 63PR PE 9.5 15.5 19.5 15.0 565

White Vinyl Glue 67SS 67PB PE 9.5 14.1 19.1 12.0 567

Solvent Base 63SS 66SD PE 7.9 12.1 16.2 4.0 563

Neoprenes 63ASS 66SD PE 7.9 12.1 16.2 7.0 563A

(Contact Cements) 66SS 66SD-3 PE 9.5 14.2 19.0 10.0 565

66SS 66SDJG PE 10.4 8.0-9.0 565

66SS 66R PE/SE 4.2 RD 565

66 66SDJG PE 10.4 8.0-9.0 565

L6SS 63PH-1 PE 9.5 14.2 19.0 10.0 565

L3BSS 63PH-1 PE 9.5 14.2 19.0 10.0 563A

CERAMICS & SIMILAR 63CVT 66PH PE 11.5 16.4 22.0 13.0 563CVT

ABRASIVE MATERIALS 64VT 64PA PE 12.1 15.0 21.0 13.0 564VT

Glazes, Engobes 67VT 67PD PE 10.0 15.0 20.0 15.0 567VT

Porcelain Enamel 68VT 68PB PE 9.5 14.1 19.1 12.0 568VT

CONCRETE CURING 66SS 200 PI 3.1 5.2 6.4 15.0 565

COMPOUNDS 67SS 206 PI 6.0 9.5 13.0 18.0 567

68SS 206 PI 6.2 9.8 13.2 20.0 568

MULTICOLOR 66SS 200 PI 3.1 5.2 12.0 565

PAINTS 67SS 206 PI 6.0 9.5 15.0 567

66SSxR3 PI 4.2 FAN 565

66SSxR8 PI 4.2 FAN 565

PTFES 63ASS 63PB PE 9.0 14.3 20.0 10.0 563A

63BSS 63PR PE 9.5 15.5 19.5 15.0 563A

66SS 66SD SE 7.9 12.1 7.0 565

HAMMERS 63CSS 63PB PE 9.0 14.3 14.0 563A

66SS 63PB PE 9.0 14.3 14.0 565

66SS 66SD SE 7.9 12.1 7.0 565

WRINKLE ENAMELS 63CSS 63PB PE 9.0 14.3 20.0 10.0 563A

66SS 63PB PE 9.0 14.3 20.0 10.0 565

ZINC RICH COATINGS 67VT 67PB PE 9.5 14.1 19.1 12.0 567VT

NOZZLE SELECTION CHART

CFM AT

MAX.

TYPE OF FLUID FLUID AIR TYPE PAT.

FLUID

TO BE SPRAYED NOZZLE NOZZLE * 30 50 70 (inches)

Needle

PSI PSI PSI AT 8 in.

No.★

FLUID NOZZLE ORIFICE SIZES

+ + + + +

59ASS 59BSS 59CSS 63SS 63ASS 63BSS 63CSS 63CVT 64VT 65SS 66SS 67SS 67VT 68SS 68VT 794

.171 .218 .281 .028 .040 .046 .052 .052 .064 .059 .070 .086 .086 .110 .110 .040

All air nozzles shown in combination with these (+) fluid nozzles can also be used in combination with any other fluid nozzle marked (+)

*See text Section B, page 6, for type code. ★All standard needles listed are stainless steel.

PTFE

* When ordering, please specify Gun Model No. and number stamped on Nozzle,

on Needle Valve Stem, or listed in Nozzle Selection Chart, page 7.

• Also available in Repair Kit 6-229.

♦ Not furnished. Please order Assembly 54-1780.

★ Available from Industrial Finishing distributors only.

❍ Available only as 5-Pack.

‡ Available only as 10-Pack.

❏ Not furnished. Can be ordered separately.

■ Replaces 54-3347 Side Port Control when using internal mix nozzles.

✔ Also available: Heavy Duty Spring 54-1372, not furnished. Please order separately.

Conventional open end or other standard wrenches are not suitable for

removing or reinserting the fluid nozzle. Optional Wrench 5-476, available

from Binks is recommended.

1 BODY

2 54-768 CONNECTION . .................................. 1

3 54-1050★ TRIGGER . .......................................... 1

4 54-750-5•❍ SPRING . .............................................. 1

5 54-1236 AIR VALVE ASSEMBLY . .................... 1

6 54-1025*• VALVE STEM ASSEMBLY* . .............. 1

7 20-3757•★ O-RING . ............................................ 1

8 54-1010★ VALVE BODY . .................................. 1

9 82-158-5•★❍ PACKING . .......................................... 1

10 82-135-5★❍ NUT . .................................................. 1

11a 54-764-5•❍ FLUID PACKING (Standard) . .............. 1

11b 2-28-10•‡ PTFE PACKING (Optional)................... 1

12 56-164 NUT . ................................................ 1

AIR NOZZLE* . .................................. 1

14 FLUID NOZZLE* . .............................. 1

15 54-918-5•★❍ GASKET. ............................................ 1

16 54-3348 HEAD . .............................................. 1

17 54-710 SCREW . ............................................ 1

18 82-126-5•★❍ SCREW . ............................................ 1

19 54-1780♦

QUICK CHANGE SIDE PORT

CONTROL . ...................................... 1

20 84-95♦★ PIN. .................................................... 1

21 54-1794♦❏ BODY (Optional) . .............................. 1

22 55-541-5♦★❍ PACKING (Optional) . .......................... 1

23 55-634♦★ RING (Optional) . ................................ 1

24 54-1804♦★ SPRING (Optional) . ............................ 1

25 54-1790♦❏ SCREW (Optional) . ............................ 1

26 20-3593♦★ SCREW (Optional). .............................. 1

27 54-1789♦ STEM (Order 54-1780). ........................ 1

28 54-3347 SIDE PORT CONTROL . ...................... 1

56-126 ■

PLUG

29 54-1014-5•❍ PIN. .................................................... 1

30 54-1015-5★❍ WASHER . .......................................... 1

31 54-304-5•❍ SPRING . ............................................ 1

32 54-738-5•❍ PACKING . .......................................... 2

33 54-1016-5❍ WASHER . ........................................ 2

34 54-1063 BODY . .............................................. 1

35 54-1023 SCREW . ............................................ 1

* FLUID NEEDLE* . .............................. 1

37 54-1347-5•✔❍ SPRING . ............................................ 1

38 20-5285-5•❍ O-RING . ............................................ 1

39 54-1013 BODY . .............................................. 1

40 54-1007 CONTROL SCREW . ............................ 1

41 54-1020• STUD . ................................................ 1

5-476

FLUID NOZZLE WRENCH (Optional)**

ITEM PART

NO. NO. DESCRIPTION QTY.

ITEM PART

NO. NO. DESCRIPTION QTY.

PARTS LIST – 2001 AND 2001V

When ordering, please specify Part No.

Binks MODELS 2001 AND 2001V SPRAY GUNS

PTFE

PARTS LIST – 2001SS

When ordering, please specify Part No.

❍ Available only as 5-pack

•

Indicates parts in Repair Kit 6-229

▲ Available only as 10-pack

❋ Accessory Item

Accessories: 56-126 Plug may replace the 54-3347 Assembly when using

internal mix nozzles.

#54-1780 QUICK CHANGE

SIDE PORT CONTROL

#54-1789 STEM

#20-3593 SCREW

#54-1790 SCREW

#54-1804 SPRING

#55-634 RING

#55-541 PACKING

#55-1794

BODY

#84-95 PIN

#82-126 SCREW

#54-710 SCREW

#54-3368 HEAD

#54-918 GASKET

*FLUID

NOZZLE

AIR NOZZLE*

#82-135 NUT

#82-158 PACKING

#54-1010 VALVE BODY

#54-1025 VALVE STEM

ASSEMBLY

#2-28 FLUID

PACKING

#56-164 NUT

#54-750

SPRING

#54-1050

TRIGGER

#54-1236 AIR VALVE

ASSEMBLY

#54-768 CONNECTION

#54-3349 BODY

#54-1020 STUD

#54-1347 SPRING

**FLUID NEEDLE

#54-1007 CONTROL SCREW

#54-5285 “O” RING

#54-1013 BODY

#54-3347

SIDE PORT

CONTROL

#54-1023 SCREW

#54-1063 BODY

#54-1016 WASHER

#54-738 PACKING

#54-304 SPRING

#54-1015 WASHER

#54-1014 PIN

#20-3757

“O” RING

Binks MODEL 2001SS SPRAY GUN

* Be sure to specify number stamped on Air Nozzle

and Fluid Nozzle, or see Nozzle Selection Chart.

Be sure to specify number stamped on Needle

Valve Stem and Gun Model when ordering.

PART

NO. DESCRIPTION QTY.

See Note

Above

AIR NOZZLE ........................................ 1

See Note

Above

FLUID NOZZLE.................................... 1

See Note

Above

FLUID NEEDLE.................................... 1

•

20-3757 “O” RING .............................................. 1

❍

•

20-5285-5 “O” RING .............................................. 1

❍

•

54-304-5 SPRING................................................ 1

54-710 SCREW ................................................ 1

❍

•

54-738-5 PACKING.............................................. 2

❍

•

54-750-5 SPRING................................................ 1

▲

•

2-28-10 FLUID PACKING .................................. 1

54-768 CONNECTION .................................... 1

❍

•

54-918-5 GASKET .............................................. 1

54-1007 CONTROL SCREW.............................. 1

54-1010 VALVE BODY........................................ 1

54-1013 BODY.................................................... 1

❍

•

54-1014-5 PIN........................................................ 1

54-1015 WASHER .............................................. 1

PART

NO. DESCRIPTION QTY.

54-1016 WASHER .............................................. 2

•

54-1020 STUD.................................................... 1

54-1023 SCREW ................................................ 1

•

54-1025 VALVE STEM ASSEMBLY.................... 1

54-1050 TRIGGER ............................................ 1

54-1063 BODY.................................................... 1

54-1236 AIR VALVE ASSEMBLY........................ 1

❍

•

54-1347-5 SPRING................................................ 1

❋ 54-1780 QUICK CHANGE SIDE PORT

CONTROL (Optional)........................ 1

54-3347 SIDE PORT CONTROL........................ 1

54-3368 HEAD.................................................... 1

54-3349 BODY (NOT FOR SALE)...................... 1

56-164 NUT ...................................................... 1

❍

•

82-126-5 SCREW ................................................ 1

❍ 82-135-5 NUT ...................................................... 1

❍

•

82-158-5 PACKING.............................................. 1

SPECIAL NOZZLES – INTERNAL MIX HEAVY MATERIAL

SPECIAL NOZZLES – SPECIAL EFFECTS

SPECIAL NOZZLE – CLEANING

FLUID

NOZZLE

#794 SS FLUID NOZZLE

#590

NEEDLE

VALVE

VEILING

DISTRESSING

AIR NOZZLE

#797 AIR NOZZLE

#793

AIR NOZZLE

#54-2065

RING

#790

CORE

#792

SPIRAL

CORE

#54-1583

BASE

#559 NEEDLE

ASSEMBLY

GUIDE

#54-1584 RING

(USED WITH 200 SERIES

TIPS ONLY)

NOZZLE TIP:

200 SERIES,

NITRALLOY

SCREW

#82-176 RING*

(USED WITH

R3 & R8 ONLY)

#54-1584 RING*

(USED WITH

200 SERIES TIPS ONLY)

#54-1583 BASE*#54-1439 GASKET*

R3, R8 AIR NOZZLE 66SS / 67SS / 68SS FLUID NOZZLE NEEDLE ASSEMBLY

#54-928 10" CLEANING ATTACHMENT

(REQUIRED FOR DEGREASING AND LUBRICATING)

MULTI-COLOR CONVERSION KIT FOR 60 SERIES NOZZLES

54-4512 KIT TO CONVERT FROM STANDARD SET-UP TO MULTI-COLOR.

SPECIAL EFFECT

FINISHES

VEILING

DISTRESS FINISH

SPATTER FINISH

SOLD ONLY AS ACCESSORIES, ORDER SEPARATELY.

Fluid Nozzle Air Nozzle Type* CFM SS Fluid Needle

794 793 PE 3 @ 15 PSI 590

794 797 PE 3 @ 15 PSI 590

66 66PD PE 3 @ 15 PSI 565

*See text Section B, page 6, for type code.

NOTES

Industrial Finishing

Binks has authorized distributors throughout the world. For technical

assistance or the distributor nearest you, see listing below.

U.S./Canada Technical Service Office:

195 Internationale Blvd., Glendale Heights, IL 60139

Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only)

Toll-Free Fax: 1-888-246-5732

Automotive Refinishing

Binks has authorized distributors throughout the world.

For equipment, parts and service, check the Yellow Pages

under “Automotive Body Shop Equipment and Supplies.”

For technical assistance, see listing below.

U.S./Canada Customer Service Office:

1724 Indian Wood Circle, Suite J-K, Maumee, OH 43537

Toll-Free Telephone: 1-800-445-3988 (U.S.A. and Canada only)

Toll-Free Fax: 1-800-445-6643

Binks Worldwide Sales and Service Listing: www.binks.com

WARRANTY

This product is covered by Binks’ 1 Year Limited Warranty.

77-2316R-14 Revisions: (P7) Updated Nozzle Selection Chart and Fluid Nozzle Orifice

Sizes chart; (P12) Updated contact information.

Binks 2001SS User manual

Brand: Binks

Model: 2001SS

Category: Power fine-spray systems

Type: User manual

This manual is also suitable for

2001
2001V

Download PDF

report

Binks 2001SS User manual

This manual is also suitable for

Binks 2001SS User manual

Related papers

Other documents