Motorola MC40 User manual

MC40

INTEGRATOR GUIDE

MC40 INTEGRATOR GUIDE

72E-166943-01

Rev. A

November 2012

ii MC40 Integrator Guide

No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means,

without permission in writing from Motorola. This includes electronic or mechanical means, such as

photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to

change without notice.

The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on

a licensed basis. Motorola grants to the user a non-transferable and non-exclusive license to use each

software or firmware program delivered hereunder (licensed program). Except as noted below, such license

may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of

Motorola. No right to copy a licensed program in whole or in part is granted, except as permitted under

copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with

other program material, create a derivative work from a licensed program, or use a licensed program in a

network without written permission from Motorola. The user agrees to maintain Motorola’s copyright notice on

the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in

whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed

program delivered to the user or any portion thereof.

Motorola reserves the right to make changes to any software or product to improve reliability, function, or

design.

Motorola does not assume any product liability arising out of, or in connection with, the application or use of

any product, circuit, or application described herein.

No license is granted, either expressly or by implication, estoppel, or otherwise under any Motorola, Inc.,

intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in

Motorola products.

iii

Revision History

Changes to the original guide are listed below:

Change Date Description

-01 Rev A 11/30/12 Initial release.

iv MC40 Integrator Guide

TABLE OF CONTENTS

About This Guide

Introduction..................................................................................................................................... xi

Documentation Set ................................................................................................................... xi

Configurations................................................................................................................................. xi

Versions.......................................................................................................................................... xii

Chapter Descriptions ...................................................................................................................... xii

Notational Conventions................................................................................................................... xii

Related Documents ........................................................................................................................ xiii

Service Information......................................................................................................................... xiii

Chapter 1: Getting Started

Introduction .................................................................................................................................... 1-1

Unpacking the MC40 ..................................................................................................................... 1-1

Getting Started ............................................................................................................................... 1-1

Installing the Battery ................................................................................................................ 1-2

Charging the Battery ................................................................................................................ 1-2

Charging the Main Battery ................................................................................................. 1-2

Charging Temperature ....................................................................................................... 1-3

Charging Spare Batteries ................................................................................................... 1-3

Powering On the MC40 ............................................................................................................ 1-3

Powering Off the MC40 ............................................................................................................ 1-4

Replacing the Battery ..................................................................................................................... 1-4

Resetting the MC40 ....................................................................................................................... 1-4

Soft Reset ................................................................................................................................ 1-5

Hard Reset ............................................................................................................................... 1-5

Enterprise Reset ...................................................................................................................... 1-5

Factory Reset ........................................................................................................................... 1-6

Waking the MC40 .......................................................................................................................... 1-7

Chapter 2: Accessories

Introduction .................................................................................................................................... 2-1

Single Slot USB Docking Cradle .................................................................................................... 2-3

vi MC40 Integrator Guide

Setup ........................................................................................................................................ 2-3

Charging the MC40 Battery ..................................................................................................... 2-3

Four Slot Charge Only Docking Cradle ......................................................................................... 2-5

Setup ........................................................................................................................................ 2-5

Four Slot Battery Charger .............................................................................................................. 2-7

Setup ........................................................................................................................................ 2-7

USB/Charge Cable ........................................................................................................................ 2-9

Charging the MC40 Battery ..................................................................................................... 2-9

2-way Charge Cable ...................................................................................................................... 2-10

Handstrap ...................................................................................................................................... 2-11

CS3070 Bluetooth Scanner ........................................................................................................... 2-14

Bluetooth Connection ............................................................................................................... 2-14

Human Interface Device Emulation ................................................................................... 2-14

Options ............................................................................................................................... 2-14

HID Pairing ............................................................................................................................... 2-14

Numeric Bar Codes for PIN Entry ............................................................................................ 2-16

Configuring the Scanner .......................................................................................................... 2-16

Replacement Bezel ........................................................................................................................ 2-17

Chapter 3: USB Communication

Connecting to a Host Computer via USB ...................................................................................... 3-1

Disconnect from the Host Computer ........................................................................................ 3-2

Chapter 4: DataWedge Configuration

Introduction .................................................................................................................................... 4-1

Basic Scanning .............................................................................................................................. 4-1

Profiles ........................................................................................................................................... 4-2

Profile0 ..................................................................................................................................... 4-2

Plug-ins .......................................................................................................................................... 4-2

Input Plug-ins ........................................................................................................................... 4-3

Bar Code Scanner Input Plug-in ........................................................................................ 4-3

Process Plug-ins ...................................................................................................................... 4-3

Basic Data Formatting Process Plug-in ............................................................................. 4-3

Output Plug-ins ........................................................................................................................ 4-3

Keystroke Output Plug-in ................................................................................................... 4-3

Intent Output Plug-in .......................................................................................................... 4-3

Profiles Screen .............................................................................................................................. 4-3

Profile Context Menu ......................................................................................................... 4-4

Options Menu ..................................................................................................................... 4-4

Disabling DataWedge .............................................................................................................. 4-5

Create a New Profile ...................................................................................................................... 4-5

Configuring a Profile ...................................................................................................................... 4-6

Applications .............................................................................................................................. 4-6

Associated Apps ................................................................................................................ 4-6

Barcode Input ........................................................................................................................... 4-7

Enabled .............................................................................................................................. 4-7

Decoders ............................................................................................................................ 4-8

Decoder Params ................................................................................................................ 4-8

UPC EAN Params .............................................................................................................. 4-13

Table of Contents vii

Reader Params .................................................................................................................. 4-14

Scan Params ...................................................................................................................... 4-15

Keystroke Output ..................................................................................................................... 4-15

Intent Output ............................................................................................................................ 4-16

Intent Overview .................................................................................................................. 4-16

DataWedge Settings ...................................................................................................................... 4-17

Import Configuration File .......................................................................................................... 4-18

Export Configuration File ......................................................................................................... 4-18

Restore DataWedge ................................................................................................................ 4-18

Configuration File Management ..................................................................................................... 4-19

Enterprise Folder ..................................................................................................................... 4-19

Auto Import .............................................................................................................................. 4-19

Programming Notes ....................................................................................................................... 4-19

Remap Keys ............................................................................................................................ 4-19

Overriding Trigger Key in an Application ................................................................................. 4-20

Capture Data and Taking a Photo in the Same Application ..................................................... 4-20

Disable DataWedge on MC40 and Mass Deploy ..................................................................... 4-20

Chapter 5: WLAN Configuration

Introduction .................................................................................................................................... 5-1

Configure a Wi-Fi Network ............................................................................................................. 5-1

Manually Adding a Wi-Fi Network .................................................................................................. 5-3

Advanced Wi-Fi Settings ................................................................................................................ 5-3

Proxy Configuration ................................................................................................................. 5-4

Remove a Wi-Fi Network ............................................................................................................... 5-5

Static IP Address ........................................................................................................................... 5-5

Chapter 6: Administrator Utilities

Introduction .................................................................................................................................... 6-1

Required Software ................................................................................................................... 6-1

On-device Application Installation ............................................................................................ 6-1

Multi-user/AppLock Configuration .................................................................................................. 6-2

Enterprise Administrator Application .............................................................................................. 6-2

Create Users ............................................................................................................................ 6-2

Add Packages .......................................................................................................................... 6-3

Create Groups ......................................................................................................................... 6-4

Save Data ................................................................................................................................ 6-4

Export Files .............................................................................................................................. 6-4

Import User List ........................................................................................................................ 6-5

Import Group List ..................................................................................................................... 6-5

Edit a User ............................................................................................................................... 6-5

Delete a User ........................................................................................................................... 6-5

Edit a Group ............................................................................................................................. 6-5

Delete a Group ......................................................................................................................... 6-6

Edit a Package ......................................................................................................................... 6-6

Delete a Package ..................................................................................................................... 6-6

MultiUser Administrator .................................................................................................................. 6-6

Disable the Multi-user Feature ................................................................................................. 6-7

Capturing a Log File ................................................................................................................. 6-7

viii MC40 Integrator Guide

AppLock Administrator ................................................................................................................... 6-8

Manual File Configuration .............................................................................................................. 6-8

Groups File .............................................................................................................................. 6-8

White List File .......................................................................................................................... 6-9

Determining Applications Installed on the MC40 ..................................................................... 6-10

Secure Storage .............................................................................................................................. 6-10

Installing a Key ......................................................................................................................... 6-10

Viewing Key List ....................................................................................................................... 6-11

Delete a Key ............................................................................................................................ 6-11

Volumes ................................................................................................................................... 6-12

Create Volume Using EFS File .......................................................................................... 6-12

Create Volume Manually .................................................................................................... 6-12

Mount Volume .................................................................................................................... 6-13

List Volumes ...................................................................................................................... 6-13

Unmount Volume ............................................................................................................... 6-13

Delete Volume ................................................................................................................... 6-14

Create EFS File ....................................................................................................................... 6-14

Off-line Extraction Tool ............................................................................................................ 6-14

Usage ................................................................................................................................. 6-14

Creating an Image ............................................................................................................. 6-15

Mounting an Image ............................................................................................................ 6-16

Unmounting an Image ........................................................................................................ 6-16

Chapter 7: Settings

Introduction .................................................................................................................................... 7-1

Location Settings ........................................................................................................................... 7-1

Screen Unlock Settings ................................................................................................................. 7-2

Single User Mode .................................................................................................................... 7-2

Set Screen Unlock Using PIN ............................................................................................ 7-2

Set Screen Unlock Using Password .................................................................................. 7-3

Screen Unlock Using Pattern ............................................................................................. 7-4

Removing or Change the Screen Lock .............................................................................. 7-5

Multiple User Mode .................................................................................................................. 7-5

Passwords ..................................................................................................................................... 7-5

Button Remapping ......................................................................................................................... 7-5

Exporting a Configuration File .................................................................................................. 7-6

Importing a Configuration File .................................................................................................. 7-6

Creating Remap File ................................................................................................................ 7-7

Enterprise Reset ...................................................................................................................... 7-7

Accounts & Sync Settings .............................................................................................................. 7-7

Language Usage ........................................................................................................................... 7-7

Keyboard Settings ......................................................................................................................... 7-8

About Device ................................................................................................................................. 7-8

Chapter 8: Application Deployment

Introduction .................................................................................................................................... 8-1

Security .......................................................................................................................................... 8-1

Secure Certificates ................................................................................................................... 8-1

Credential Storage Settings ..................................................................................................... 8-2

Table of Contents ix

Development Tools ........................................................................................................................ 8-2

Development Settings .............................................................................................................. 8-3

ADB USB Setup ............................................................................................................................. 8-3

Windows XP and Windows 7 Installation ................................................................................. 8-3

Linux Installation ...................................................................................................................... 8-4

Application Installation ................................................................................................................... 8-4

Installation Using USB Connection .......................................................................................... 8-5

Using Android Debug Bridge ................................................................................................... 8-5

Mobility Services Platform ........................................................................................................ 8-6

Uninstall an Application ............................................................................................................ 8-6

System Update .............................................................................................................................. 8-7

Storage .......................................................................................................................................... 8-8

Random Access Memory ......................................................................................................... 8-8

External Storage ...................................................................................................................... 8-9

Internal Storage ....................................................................................................................... 8-10

Enterprise Folder ..................................................................................................................... 8-10

Managing Applications ................................................................................................................... 8-11

Get Details About an Application ............................................................................................. 8-11

Stopping an Application ........................................................................................................... 8-12

Changing Application Location ...................................................................................................... 8-12

Managing Downloads .................................................................................................................... 8-13

Chapter 9: Maintenance & Troubleshooting

Introduction .................................................................................................................................... 9-1

Maintaining the MC40 .................................................................................................................... 9-1

Battery Safety Guidelines .............................................................................................................. 9-1

Cleaning ......................................................................................................................................... 9-2

Approved Cleanser Active Ingredients ..................................................................................... 9-2

Harmful Ingredients .................................................................................................................. 9-3

Cleaning Instructions ............................................................................................................... 9-3

Special Cleaning Notes ............................................................................................................ 9-3

Materials Required ................................................................................................................... 9-3

Cleaning the MC40 .................................................................................................................. 9-3

Housing .............................................................................................................................. 9-3

Display ............................................................................................................................... 9-3

Camera Lens ...................................................................................................................... 9-3

Connector ........................................................................................................................... 9-3

Cleaning Cradle Connectors .................................................................................................... 9-4

Cleaning Frequency ................................................................................................................. 9-4

Troubleshooting ............................................................................................................................. 9-5

MC40 ....................................................................................................................................... 9-5

Single Slot USB Docking Cradle .............................................................................................. 9-7

Four Slot Charge Only Docking Cradle .................................................................................... 9-7

Four Slot Spare Battery Charger ............................................................................................. 9-8

USB/Charge Cable .................................................................................................................. 9-8

Appendix A: Technical Specifications

MC40 Technical Specifications ...................................................................................................... A-1

Connector Pin-outs ........................................................................................................................ A-3

x MC40 Integrator Guide

I/O Connector Pin-Outs ............................................................................................................ A-3

HDMI Connector Pin-outs ........................................................................................................ A-4

Headset Connector .................................................................................................................. A-6

Expansion Module Connector Pin-outs .................................................................................... A-6

MC40 Accessory Specifications .................................................................................................... A-8

Single Slot USB Docking Cradle .............................................................................................. A-8

Four Slot Battery Charger ........................................................................................................ A-8

Four Slot Charge Only Docking Cradle .................................................................................... A-9

USB/Charge Cable .................................................................................................................. A-9

2-way Charge Cable ................................................................................................................ A-10

Appendix B: Keypad Remap Strings

Introduction .................................................................................................................................... B-1

Glossary

Index

ABOUT THIS GUIDE

Introduction

This guide provides information about using the MC40 and accessories.

Documentation Set

The documentation set for the MC40 provides information for specific user needs, and includes:

•

MC40 Quick Start Guide - describes how to get the MC40 up and running.

•

MC40 User Guide - describes how to use the MC40.

•

MC40 Integrator Guide - describes how to set up the MC40 and accessories.

Configurations

This guide covers the following configurations:

NOTE Screens and windows pictured in this guide are samples and can differ from actual screens.

Configuration Radios Display Memory

Data Capture

Options

Operating

System

MC40N0 WLAN: 802.11a/b/g/n

WPAN: Bluetooth v2.1

with EDR

4.3” WVGA

Color

1 GB RAM /

8 GB Flash

camera and

imager or

camera, imager

and MSR with

encryption

capability*

Android based,

Android

Open-Source

Project 2.3

* Contact Motorola Solutions for more information.

xii MC40 Integrator Guide

Versions

To determine the current hardware and software versions touch > Settings > About device.

•

Serial number - Displays the serial number.

•

Model number - Displays the model number.

•

Android version - Displays the operating system version.

•

Kernel version - Displays the kernel number.

•

Build number - Displays the software build number.

Chapter Descriptions

Topics covered in this guide are as follows:

•

Chapter 1, Getting Started provides information on getting the MC40 up and running for the first time.

•

Chapter 2, Accessories describes the available accessories and how to use them with the MC40.

•

Chapter 3, USB Communication describes how to connect the MC40 to a host computer using USB.

•

Chapter 4, DataWedge Configuration describes how to use and configure the DataWedge application.

•

Chapter 5, WLAN Configuration describes the available accessories and how to use them with the

MC40.

•

Chapter 6, Administrator Utilities provides information for using the suite of administrative tools for

configuring the MC40.

•

Chapter 7, Settings describes the settings for configuring the MC40.

•

Chapter 8, Application Deployment explains Bluetooth functionality on the MC40.

•

Chapter 9, Maintenance & Troubleshooting includes instructions on cleaning and storing the MC40, and

provides troubleshooting solutions for potential problems during MC40 operation.

•

Appendix A, Technical Specifications provides the technical specifications for the MC40.

•

Appendix B, Keypad Remap Strings provides a list of keypad remap strings.

Notational Conventions

The following conventions are used in this document:

•

Italics are used to highlight the following:

• Chapters and sections in this and related documents

• Icons on a screen.

•

Bold text is used to highlight the following:

• Dialog box, window, and screen names

• Drop-down list and list box names

• Check box and radio button names

• Key names on a keypad

• Button names on a screen.

About This Guide xiii

•

bullets (•) indicate:

• Action items

• Lists of alternatives

• Lists of required steps that are not necessarily sequential

•

Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.

Related Documents

•

MC40 Quick Start Guide, p/n 72-167493-xx.

•

MC40 Regulatory Guide, p/n 72-166942-xx.

•

MC40 User Guide, p/n 72E-166940-xx.

•

MSP Client Software Guide, p/n 72E-128805-xx

For the latest version of this guide and all guides, go to: http://supportcentral.motorola.com

Service Information

If you have a problem with your equipment, contact Motorola Solutions support for your region. Contact

information is available at: http://www.motorolasolutions.com/support.

When contacting Motorola Solutions Global Customer Support, please have the following information

available:

•

Serial number of the unit (found on manufacturing label)

•

Model number or product name (found on manufacturing label)

•

Software type and version number

Motorola Solutions responds to calls by email or telephone within the time limits set forth in support

agreements.

Manufacturing label

xiv MC40 Integrator Guide

If your problem cannot be solved by Motorola Solutions Support, you may need to return your equipment for

servicing and will be given specific directions. Motorola Solutions is not responsible for any damages incurred

during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void

the warranty.

If you purchased your Motorola Solutions business product from a Motorola business partner, contact that

business partner for support.

CHAPTER 1 GETTING STARTED

Introduction

This chapter provides information about the MC40, accessories, charging, and resetting the MC40.

Unpacking the MC40

Carefully remove all protective material from the MC40 and save the shipping container for later storage and

shipping. Verify that you received the following equipment:

•

MC40

•

Lithium-ion battery

•

Regulatory Guide

•

Quick Start Guide.

Inspect the equipment. If any equipment is missing or damaged, contact the Motorola Solutions Global

Customer Support immediately. See Service Information on page xiii for contact information.

Prior to using the MC40 for the first time, remove the protective shipping film that covers the scan window,

display and camera window.

Getting Started

To start using the MC40 for the first time:

1. Install the main battery.

2. Charge the MC40.

3. Power on the MC40.

1 - 2 MC40 Integrator Guide

Installing the Battery

To install the battery:

1. Align the battery with the slots in the battery compartment.

2. Lower the battery and snaps into place.

3. Press down on the battery latch. If the battery is charged, the MC40 turns on automatically.

Figure 1-1

Inserting the Battery

Charging the Battery

Charging the Main Battery

Before using the MC40 for the first time, charge the main battery until the Right light emitting diode (LED) turns

solid green (see Table 1-1 on page 1-3 for charge status indications). To charge the MC40, use a cable or a

cradle with the appropriate power supply. For information about the accessories available for the MC40, see

Chapter 7, Accessories.

The MC40 is equipped with a memory backup battery that automatically charges from the fully-charged main

battery. When using the MC40 for the first time, the backup battery requires approximately 36 hours to fully

charge. This is also true any time the backup battery is discharged, which occurs when the main battery is

removed for several hours. The backup battery retains random access memory (RAM) data in memory for at

least 10 minutes (at room temperature) when the MC40’s main battery is removed, when Battery Swap feature

is used. When the MC40 reaches a very low battery state, the combination of main battery and backup battery

retains RAM data in memory for at least 48 hours.

For cable and cradle setup and charging procedures, see Chapter 2, Accessories.

•

Micro USB Cable

•

Single Slot Charging Cradle

•

Five Slot Universal Charge Only Cradle.

To charge the main battery:

CAUTION Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on page

9-1.

Getting Started 1 - 3

1. Connect the charging accessory to the appropriate power source.

2. Insert the MC40 into a cradle or attach to a cable. The MC40 begins charging. The Right LED blinks amber

while charging, then turns solid green when fully charged. See Table 1-1 for charging indications.

The 2680 mAh battery charges in approximately four hours.

Charging Temperature

Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Note that charging is intelligently

controlled by the MC40. To accomplish this, for small periods of time, the MC40 or accessory alternately

enables and disables battery charging to keep the battery at acceptable temperatures. The MC40 or accessory

indicates when charging is disabled due to abnormal temperatures via its LED. See Table 1-1.

Charging Spare Batteries

See Chapter 2, Accessories for information on using accessories to change spare batteries.

Powering On the MC40

If the MC40 did not turn on when the battery was installed, press the Power button until the Right and Left

LEDs flash once. The splash screen displays for about a minute as the MC40 initializes its flash file system.

Note that these windows also appear upon reset.

Replacing the Battery

To replace the battery:

Table 1-1

Battery Charge LED Status

Status Indication

Off MC40 is not charging.

MC40 is not inserted correctly in the cradle.

MC40 is not connected to a power source.

Charger or cradle is not powered.

Slow Blinking Amber

(3 blinks every 2 seconds)

MC40 is charging.

Solid Green Fully charged.

Fast Blinking Amber

(3 blinks/second)

Charging error, e.g.:

•

Temperature is too low or too high.

•

Charging has gone on too long without completion (typically eight hours).

Flashes Amber once when

Power button pressed

Critical battery level. Battery too low to boot device.

Fast blinking Amber when

Power button pressed

Battery over-temperature condition. Device shuts down. Battery will not charge

until temperature returns to normal operating value.

NOTE Ensure that the Battery Swap mode procedures are followed, otherwise the backup battery will deplete

quickly.

1 - 4 MC40 Integrator Guide

1. Press the Power button until the Device options menu displays.

2. Touch Battery swap. The Right and Left LEDs light red.

3. Wait until the LEDs turns off.

4. Lift the battery latch.

Figure 1-2

Removing the Battery

5. Remove the battery out of the battery compartment.

Figure 1-3

Remove Battery

6. Align the replacement battery in the battery compartment.

7. Lower the battery and press down until it snaps into place.

8. Press down on the battery latch. If the battery is charged, the MC40 turns on automatically.

Resetting the MC40

There are four reset functions:

Page is loading ...

Motorola MC40 User manual

Motorola MC40 User manual

Related papers

Other documents